Argox AS-8312 User manual

0
NOTICE:
This equipment has been tested and it complies with
the limits for a Class a digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to
provide a reasonable protection against harmful
interference when the equipment is operated under a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expenses.
Note: All brands and trademarks shall belong to their
respective owner.
Note: Specification is subject to changes without
notice.
This device complies with Part 15 of the FCC Rules.
Operation shall be subject to the following two
conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interface received,
including interface that may cause undesirable
operation.

1
Introduction
Installation- Keyboard Wedge
1) First of all, you must switch off power for the
terminal/computer.
2) Disconnect the keyboard cable from the back of the
terminal/computer.
3) Connect the appropriate interface cable to the scanner
and to the terminal/computer.
4) Turn the terminal/computer power on.
RS-232
1) Disconnect power to the terminal/computer.
2) Connect the appropriate interface cable and external
power supply (DC adapter) to the scanner.
3) Plug the serial connector into the serial port on the back
of your computer/terminal. Tighten the two screws to
secure the connector to the port.
4) Plug the power pack into power source.
5) Once the scanner has been fully connected, turn the
terminal/computer power back on.
USB (Simulate with keyboard wedge)
1) Connect the USB cable between scanner and PC.
2) Windows will automatically detect the USB device.
Note: If any of the above operation is incorrect, turn off the
power immediately and check any improper
connections. Go through all above steps again.

2
Default setting
For each barcode shown as below:
Code Type
Read
Enable
Checksum
Verification
Enable
Checksum
Transmission
Enable
Code
ID
8110 / 8120
UPC-A
V
V
V
A
UPC-E
V
V
V
E
EAN-13
V
V
V
F
EAN-8
V
V
V
FF
Code-39
V
＊
Interleaved
2 of 5
V
i
Industrial
2 of 5
-
-
i
Matrix 2 of 5
B
Codabar
V (8110)
%
Code-128
V
V
#
Code-93
V two digits
&
Code-11
VOne digit
O
MSI/Plessey
V
@
UK/Plessey
V
@
Telepen
S
Standard 2 of 5
-
-
i
RSS-14
-
-
R4
RSS-Limited
-
-
RL
RSS-Expanded
-
-
RX
China Post
t
Italian
Pharmacode.
p

3
Code Type
Read
Enable
Checksum
Verification
Enable
Checksum
Transmission
Enable
Code
ID
8150
8250
8310
8312
UPC-A
V
V
V
V
A
UPC-E
V
V
V
V
E
EAN-13
V
V
V
V
F
EAN-8
V
V
V
V
FF
Code-39
V
V
＊
Interleaved
2 of 5
V
V
i
Industrial
2 of 5
-
-
i
Matrix 2 of 5
B
Codabar
%
Code-128/
GS1-128
V
V
V
#
Code-93
V two digits
&
Code-11
VOne digit
O
MSI/Plessey
V
@
UK/Plessey
V
@
Telepen
S
Standard 2 of 5
V
V
i
China Post
t
Italian
Pharmacode.
p
Code-16K
-
-
-
PDF417
-
V
-
-
EAN UCC
Composite
-
-
-
RC
RSS-14
-
R4
RSS-Limited
-
RL
RSS-Expanded
-
RX
Micro-PDF
-
8312
only
-
-
U

4
Weight
155 g
120 g
ArgoScan 8110 / 8120
Specification
Model 8110
Model 8120
Operational
Light Source
660 nm Visible Red LED
Optical System
2048 pixel CCD
(Charge-coupled device)
Depth of Scan Field
0-80 mm
(CODE 39,
PCS=90%, 20mils)
0-150 mm
(code 39,
PCS=90%, 20mils)
Scanning Width
80 mm at contact
75mm at contact
Scan Speed
50 scans/sec
100 scans/sec
Resolution
4mils, Code39, PCS=90%, on contact
5mils, Code39, PCS=45%, on contact
Print Contrast
30% or more
Scanning Angle
Pitch: 60° Skew: 75°
Decode Capability
Auto-discriminates all standard
barcodes; Other symbologies can be
ordered optionally
Beeper Operation
7 tones or no beep
Indicator
Green led
Blue led
Mechanical
Length
182 mm
Width-handle
26 mm
Width-head
90 mm
Depth-handle
51 mm
49mm
Depth-head
35 mm

5
Cable –K/B wedge
Straight 2.0 m
Cable –universal
type
Straight 2.3 m
Connector type
RJ-45 phone jack connector
Case material
ABS
Cushion material
Rubber
Electrical
Input Voltage
5 VDC ± 0.25V
Power - Operating
380 mW
850mW
Power - Standby
240 mW
250 mW
Current - Operating
76 mA @ 5 VDC
170 mA@5 VDC
Current - Standby
48 mA @ 5 VDC
50 mA@5 VDC
DC Transformers
Class 2; 5VDC @ 450 mA
Agency listing
FCC Class A,CE, BSMI
Environmental
Operating
Temperature
0℃to 45℃(32℉to 113℉)
Storage
-20℃to 60℃
(-4℉to 140℉)
Humidity
5% to 90% relative humidity,
non-condensing
Light Level
Up to 15000 Lux.
Up to 20000 Lux.
Shock
1.0m
1.2m
Contaminants
Seals to resist airborne particulate
contaminants
Ventilation
None required

6
Programming
Programming
method
Manual (Reading special barcode) DOS
command through RS-232, Windows
configuration program (8110)
Program upgrade
Enabled built-in flash memory (8110)
Programmable
characteristics
Code type selection, check digit
selection Decoding option Decoding
option Transmitted character delay,
Header selection, trailer selection,
message suffix, good read beep tone
and volume, scanner trigger selection
Keyboard emulation type
(intermessage delay, keyboard type
and keyboard language)
Serial interface type (ACK/NAK,
Xon/Xoff, RTS/CTS, good read LED
control, start/stop bits)

7
ArgoScan 8150 / 8250 / 8310 / 8312
Specification
Model
8150/8250
Model
8310/8312
Operational
Light Source
660 nm Visible Red
LED
630 nm Visible Red
LED
Optical System
2048 pixel CCD
(Charge-coupled device)
Depth of Scan Field
0-250 mm
(CODE 39,
PCS=90%, 20mils)
Up to 600mm
(CODE 39,
PSC=90%, 20mils)
Scanning Width
120 mm
160mm
Scan Speed
200 scans/sec
450 scans/sec
Resolution
0.1mm(4mils);
Code39,PCS=90%,
on contact (8150);
Code39,PCS=45%,
on contact (8250)
0.1mm(4mils)
Code39,PCS=90%
Print Contrast
25% or more
25% or more
Scanning Angle
Front: 60° Rear: 60° Yaw: 75°
Decode Capability
Auto-discriminates all standard
barcodes; Other symbologies can be
ordered optionally (2D symbologies for
8250 and 8312 only)
Beeper Operation
7 tones or no beep
Indicator
Green led
Green & Red led
Mechanical
Length
182 mm
164 mm

8
Depth-head
35 mm
35 mm
Weight
150 g (cable not
included)
176 g (cable not
included)
Cable –K/B wedge
Straight 2.0 m
Coiled 2.5 m
Cable –universal
type
Straight 2.3 m
Coiled 2.5 m
Cable- USB
Straight 2.0 m
Coiled 2.5 m
Connector type
RJ-45 phone jack connector
Case material
ABS plastic
ABS (over molded
at contact pointed)
Cushion material
Rubber
Double injection
Electrical
Input Voltage
5 VDC ± 0.25V
Power - Operating
1275 mW
800 mW
Power - Standby
600 mW
350 mW
Current - Operating
255 mA (8150);
180 mA (8250)
@ 5 VDC
160 mA @ 5 VDC
Current - Standby
120 mA (8150);
100 mA (8250)
@ 5 VDC
70 mA @ 5 VDC
DC Transformers
Class 2; 5VDC @ 450 mA
Agency listing
UL, FCC Class A,
CE
UL, FCC Class B,
CE
Environmental
Width-handle
26 mm
30 mm
Width-head
74 mm
78 mm
Depth-handle
51 mm
56 mm

9
Operating
Temperature
0℃to 45℃
(32℉to 113℉)
0℃to 45℃
(32℉to 113℉)
Storage
-40℃to 60℃
(-40℉to 140℉)
-20℃to 60℃
(-4℉to 140℉)
Humidity
5% to 90% relative humidity,
non-condensing
Light Level
Up to 60000 (8150);
80000 (8250) Lux.
Up to 70000 Lux.
Shock
1.5m drop onto concrete
Contaminants
Seals to resist airborne particulate
contaminants (IP42)
Ventilation
None required
Programming
Programming
method
Manual (Reading special barcode) DOS
command through RS-232, Windows
configuration program
Program upgrade
Enabled by built-in flash memory
Programmable
characteristics
Code type selection, check digit
selection Decoding option Decoding
option Transmitted character delay,
Header selection, trailer selection,
message suffix, good read beep tone
and volume, scanner trigger selection
Keyboard emulation type
(intermessage delay, keyboard type
and keyboard language)
Serial interface type (ACK/NAK,
Xon/Xoff, RTS/CTS, good read LED
control, start/stop bits)