RIOTEC LS6300V User manual

1
Programming Quick Guide
-LS6300V/LS6320V
Installation
Make sure that the scanner has the correct cable to plug in the PC
as below described:
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the incorrect
codes, please scan from A1 to A10 for USB HID or B1 to B7 for RS232 or USB
Serial. This will reset the scanner to its factory defaults.
USB HID
RS232 or USB Serial
A1
Demo
W010F01
B1
Demo
W010F01
A2
Demo
WFFD980
B2
Demo
WFFD980
A3
Demo
W010F01
B3
Demo
W010F01
A4
Demo
W031A00
B4
Demo
WFF115D
A5
Demo
W100900
B5
W306A20
A6
Demo
WFFD9C3
B6
W016500
A7
Demo
WFF115D
B7
Demo
W010F00
A8
W306A20
A9
W016500
A10
Demo
W010F00
Barcode Configuration Method:
(Flow chart for setup procedure :)
W010F01
W010F00
Start
Configuration
End
Configuration
Auto sensing (For LS6320V only)
Auto-Sensing ON:
pressing trigger button for 5 seconds to
activate auto-sensing function (defaults)
Auto-Sensing OFF:
Press trigger button for 5 seconds again to
turn off auto-sensing function.
Emulate Numeric Keypad
Enable
Disable
W041A04
W041A00
Keyboard Language
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
Turkey1
France
WFF1919
WFF1907
Finland
Belgium
WFF1906
WFF1901
Brazil
U.S.
WFF1902
WFF1900
Canada
Czech
WFF1903
WFF1904
Denmark
Austria
WFF1905
WFF1908
Greece
Hungary
WFF1909
WFF190A
Italy
Netherland
WFF190C
WFF190E
Norway
Spain
WFF190F
WFF1916

2
Barcode Configuration Method:
(Flow chart for setup procedure :)
W010F01
W010F00
Start
Configuration
End
Configuration
Symbologies –1
ENABLE
CODE 93
DISABLE
W017601
W017600
ENABLE
CODE 11
DISABLE
W017701
W017700
Symbologies –2
ENABLE
CODE 128
DISABLE
W016101
W016100
ENABLE
UCC
EAN-128
DISABLE
W036203
W036200
ENABLE
INTERLEAVED 25
DISABLE
W016C01
W016C00
ENABLE
INDUSTRIAL 25
DISABLE
W017201
W017200
ENABLE
STANDARD 25
DISABLE
W017301
W017300
ENABLE
MATRIX 25
DISABLE
W017101
W017100
ENABLE
UPC-E
DISABLE
W016901
W016900
ENABLE
UPC-A
DISABLE
W036B02
W036B00
Symbologies –3
ENABLE
EAN-8
DISABLE
W016501
W016500
ENABLE
EAN-13
DISABLE
WC06500
W016600
ENABLE
CODE 39
DISABLE
W017401
W017400
ENABLE
CODABAR
DISABLE
W017501
W017500
Inter-Keystroke Delay (For USB HID Only)
This parameter specifies the delay between emulated keystrokes
No Delay
Short Delay
(5ms)
Demo
.
w w w .tec-it.com
.
Medium Delay
(10ms)
Long Delay (15ms)
Demo
.
WC01AC0
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_170418_01