Artecta 50 SW User manual

Display Track Profile 50 SW
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: A0320160 –Black housing
A0320161 –White housing
USER MANUAL
ENGLISH
V1

1
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Preface
Thank you for purchasing this Artecta product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2020 Artecta. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document, please visit our website www.highlite.com or contact us at
[e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Table of contents
1. Introduction..........................................................................................................................................................3
Before Using the Product ..................................................................................................................................3
Intended Use .......................................................................................................................................................3
LEDs Lifespan .......................................................................................................................................................3
Text Conventions ................................................................................................................................................3
Symbols and Signal Words................................................................................................................................4
Symbols on the Information Label ..................................................................................................................4
2. Safety ....................................................................................................................................................................5
Warnings and Safety Instructions ....................................................................................................................5
Requirements for the User.................................................................................................................................7
3. Description of the Device ...................................................................................................................................8
Front View ............................................................................................................................................................8
Back View ............................................................................................................................................................8
Product Specifications ......................................................................................................................................9
Dimensions.........................................................................................................................................................10
4. Installation and Deinstallation .........................................................................................................................11
Safety Instructions.............................................................................................................................................11
Personal Protective Equipment .....................................................................................................................11
Installation Site Requirements ........................................................................................................................11
Mounting............................................................................................................................................................12
Direction Adjustment .......................................................................................................................................13
Color Frame Installation ..................................................................................................................................14
Dismounting.......................................................................................................................................................15
Connecting to Power Supply.........................................................................................................................15
5. Operation ...........................................................................................................................................................16
Safety Instructions for Operation...................................................................................................................16
Manual Control.................................................................................................................................................16
Focusing and Zooming..............................................................................................................................16
Beam Shaping.............................................................................................................................................17
Replacing the Gobo .......................................................................................................................................18
Changing the Gobo ..................................................................................................................................19
6. Troubleshooting .................................................................................................................................................20
7. Maintenance .....................................................................................................................................................20
Safety Instructions for Maintenance.............................................................................................................20
Preventive Maintenance................................................................................................................................20
Basic Cleaning Instructions .......................................................................................................................21
Corrective Maintenance................................................................................................................................21
Replacing the Fuse.....................................................................................................................................21
8. Transportation and Storage..............................................................................................................................22
Instructions for Transportation ........................................................................................................................22
Storage...............................................................................................................................................................22
9. Disposal ..............................................................................................................................................................22
10. Approval.............................................................................................................................................................22

3
Display Track Profile 50 SW
Product code: A0320160 / A0320161
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Artecta Display Track Profile 50 SW
(including track adapter)
●Barndoor
●Color frame
●User manual
Fig. 01
Intended Use
This device is intended for professional use as an architectural light spot. It is suitable for indoor installation
in shops, exhibition halls, showrooms and similar venues. This device is not suitable for households.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.
Text Conventions
Throughout the user manual the following text conventions are used:
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment handle (05)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips

4
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting
bracket.
The information label contains the following symbols:
This device is designed for indoor use.
This device falls under IEC protection class I.
This device shall not be treated as household waste.

5
Display Track Profile 50 SW
Product code: A0320160 / A0320161
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
●Do not open the device or remove any covers.
●Do not operate the device if the covers or the housing is open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened.
●Disconnect the device from electrical power supply before service and maintenance.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class I.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
track system with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●For replacement use fuses of the same type and rating only.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the interconnecting power
cable.
●Make sure that the interconnecting power cable is not crimped or damaged. Examine the power
cable periodically for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.

6
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.
Attention
General safety
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.
●If the device fails to work properly, discontinue the use immediately.
Attention
This device shall be used only for the purposes it is designed for.
This device is intended for professional use as an architectural light spot. It is suitable for indoor installation
in shops, exhibition halls, showrooms and similar venues.
●This device is not suitable for households.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention
Before use, examine the device visually for any defects.
Make sure that:
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The interconnecting power cable is not damaged and does not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.

7
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

8
Display Track Profile 50 SW
Product code: A0320160 / A0320161
3. Description of the Device
The Artecta Display Profile 50 SW is a versatile lighting fixture suitable for indoor venues. It features two
selectable color temperatures: warm white and cold white. It has manual zooming and a built-in,
manually controllable dimmer (5 –100 %). The internal manual framing system allows you to adjust the
projection surface in any shape, which can be used for illuminating paintings, for example. The device is
delivered with a gobo holder and a color frame.
The Artecta Display Profile 50 SW is equipped with a 3-phase track adapter, which is compatible with the
Artecta 3-phase track systems and with the most 3-phase tracks available on the market.
Front View
01) Track adapter
02) Track lock
03) Circuit selector (OFF, 1, 2 and 3)
04) Mounting bracket
05) Interconnecting cable
06) 4 x Framing shutters
07) 3 x Color frame holders
08) Lens
09) Color frame clip
10) Spring-loaded screw
11) Gobo slot cover plate
12) 2 x Cover plate thumbscrews
13) Gobo holder
Fig. 02
Back View
14) Zoom control
15) Focus control
16) Adjustment handle
17) Power connector IN 100–240 V, 50/60 Hz
18) Fuse F1 AL/250 V AC
19) Color temperature switch (CW, OFF, WW)
20) Manual dimmer control
Fig. 03

9
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Product Specifications
Model:
Display Track Profile 50 SW
Electrical:
Input voltage:
100–240 V AC, 50/60 Hz
Power consumption:
56 W
PFC:
0,93
Fuse:
F1 AL, 250 V
Physical:
Dimensions:
405 x 171 x 321 mm (L x W x H) (with track adapter)
Weight:
2,8 kg (with track adapter)
Track adapter:
Power connection:
220–250 V, 10 A
F max:
100 N
Phases:
3
Optics:
Light source:
50 W Dual Color COB LED
Dimmer:
5–100 %
Zoom:
Manual
Beam angle:
13°–30°
Focus:
Manual
Framing system:
4 framing shutters
Color temperature:
3000 K and 6000 K (selectable)
Output:
3000 K –366 lm (13°); 963 lm (30°)
6000 K –561 lm (13°); 1504 lm (30°)
CRI:
>95
Effects:
Gobo slot:
Yes
Gobo holder:
Yes
Gobo size:
Ø 23,5 x 0,52 mm; image size: Ø 21 mm
Operation and control:
Control:
Manual
Construction:
Housing:
Extruded aluminum
Color:
Black (product code: A0320160)
White (product code: A0320161)
IP rating:
IP20
Cooling:
Natural convection
Thermal:
Maximum ambient temperature ta:
40 °C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
0,5 m

10
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Dimensions
Fig. 04

11
Display Track Profile 50 SW
Product code: A0320160 / A0320161
4. Installation and Deinstallation
Safety Instructions
WARNING
Incorrect installation and deinstallation can cause serious injuries and damage of
property.
Installation and deinstallation of the device must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning electrical installations in
buildings and working at heights.
Before installing or deinstalling the device make sure that the track system is disconnected from power
supply.
Personal Protective Equipment
During installation and deinstallation wear personal protective equipment in compliance with the
national and site-specific regulations.
Installation Site Requirements
●The device can be used only indoors.
●The device can be mounted only to a 3-phase track system.
●The minimum distance to other objects must be bigger than 0,5 m.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.

12
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Mounting
The device can be mounted only to a 3-phase track system.
CAUTION
Restrict the access under the work area during mounting.
To mount the device, follow the steps below:
01) Make sure that the circuit selector (03) is in OFF position and the track lock (02) is in unlocked
position, as shown in Fig. 05.
02) Align the flange of the track adapter (01) with the track, as shown in Fig. 06.
Fig. 05
Fig. 06
03) Insert the track adapter (01) in the track and push it until it snaps into place.
04) Turn the track lock (02) clockwise to lock the device in the track, as shown in Fig. 08.
Fig. 07
Fig. 08

13
Display Track Profile 50 SW
Product code: A0320160 / A0320161
05) Select the circuit with the circuit selector (03). You can select 1-, 2- and 3-phase circuit, as shown in
Fig. 09.
Attention
Do not slide the track adapter in the track to adjust the position of the device (see Fig. 10). This can
damage the connectors. Remove the device from the track and install it at the new place. For more
information on how to remove the device from the track, refer to 4.7. Dismounting on page 15.
Fig. 09
Fig. 10
Direction Adjustment
To adjust the angle of the device and the direction of the beam, follow the steps below:
01) Pivot the device around the track adapter (01) to adjust the direction of the beam (see Fig. 11).
02) Turn the adjustment handle (16) counterclockwise to release it.
03) Tilt the device at the desired angle (see Fig. 12).
04) Turn the adjustment handle (16) clockwise to tighten it. Make sure that the device cannot move
freely after the adjustment handle (16) is tightened.
Fig. 11
Fig. 12

14
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Color Frame Installation
The Display Track Profile 50 SW is delivered with a color frame. You can insert a color gel or a diffusion filter
into the color frame. To install the color frame, follow the steps below:
01) Push the spring-loaded screw (10)and at the same time lift and flip backwards the color frame
clip (09) (see Fig. 13).
02) Insert a color gel or a diffusion filter into the color frame.
03) Insert the color frame into the color frame holders (07) (see Fig. 14).
04) Pull the color frame clip (09) downwards to release the spring-loaded screw (10) (see Fig. 15). The
color frame will be locked in position.
Make sure that the color frame is locked in position with the color frame clip before using the device.
Fig. 13
Fig. 14
Fig. 15

15
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Dismounting
CAUTION
Restrict the access under the work area during dismounting.
To dismount the device, follow the steps below:
01) Set the color temperature switch (19) to OFF position to turn the device off.
02) Let the device cool down before dismounting.
03) Make sure that the circuit selector (03) is in OFF position, as shown in Fig. 16.
Fig. 16
04) Turn the track lock (02) counterclockwise to unlock the device (see Fig. 17).
05) Pull the track adapter (01) from the track (see Fig. 18).
Fig. 17
Fig. 18
Connecting to Power Supply
This device is suitable for mounting only to a 3-phase track system. The device is connected to power
supply when it is mounted to the track system.

16
Display Track Profile 50 SW
Product code: A0320160 / A0320161
5. Operation
Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is intended for professional use as an architectural light spot. It is suitable for indoor installation
in shops, exhibition halls, showrooms and similar venues. This device is not suitable for.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Manual Control
The Display Track Fresnel 50 SW can be operated only manually. The device is equipped with a color
temperature switch and a manual dimmer control.
●Set the color temperature switch (19) to CW or WW position to turn the device on.
●CW (cold white) position –the light will turn on with a predefined color temperature of 6000 K
●WW (warm white) position –the light will turn on with a predefined color temperature of 3000 K
●Turn the manual dimmer control (20)to adjust the light intensity. The adjustment range is 5–100 %.
●Set the color temperature switch (19) to OFF position to turn the device off.
Focusing and Zooming
You can manually adjust the focus and the beam angle of the Display Track Profile 50 SW. The beam
angle is adjustable in the range 13–30°.
01) Turn the focus control (15) and the zoom control (14) counterclockwise to loosen them.
02) Slide the controls forwards or backwards to adjust the zoom and the focus (see Fig. 19).
03) Once the fixture is focused, turn the focus control (15) and the zoom control (14) clockwise to tighten
them. Do not overtighten them.
Fig. 19

17
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Beam Shaping
You can shape the beam with the 4 framing shutters (06).
Move the framing shutters (06) back and forth to modify the shape of the beam (see Fig. 20).
Fig. 20

18
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Replacing the Gobo
The Display Track Profile 50 SW is delivered with a gobo holder and a set of 5 metal gobos with seasonal
patterns. You can order an additional gobo set of 5 metal gobos with general patterns (product code:
SPHAOT076). To replace the gobo, follow the steps below:
01) Loosen the 2 cover plate thumbscrews (12)(see Fig. 21). Do not remove them.
02) Slide the gobo slot cover plate (11) towards the lens (08) (see Fig 22).
03) Take the gobo holder (13)out the of gobo slot (see Fig. 23).
Fig. 21
Fig. 22
Fig. 23
04) Change the gobo in the gobo holder (13). See 5.3.1. Changing the Gobo on page 19 for more
information.
05) Insert the gobo holder (13)back into the gobo slot (see Fig. 24).
06) Slide the gobo slot cover plate (11)towards the gobo holder (13)(see Fig. 25).
07) Tighten the 2 cover plate thumbscrews (12) to secure the gobo slot cover plate (11) at its place (see
Fig. 26).
Fig. 24
Fig. 25
Fig. 26

19
Display Track Profile 50 SW
Product code: A0320160 / A0320161
Changing the Gobo
To change the gobo, follow the steps below:
01) Remove the retaining ring from the gobo holder (13) with needle-nose pliers or a similar sharp tool.
02) Change the metal gobo. Make sure that the painted (black) side of the gobo is facing upwards as
shown in Fig. 27. When inserted back into the gobo slot, the painted (black) side should be facing
the lens (08).
Fig. 27
Fig. 28
03) Place the retaining ring back on the gobo holder (13).