Artel FiberLink 3350 Series User manual

1
The FiberLink 3350 Series of fiber optic transmission systems are ready for immediate use
and do not require any special tools or equipment. However, an Optical Power Meter, such
as the FiberLink 6615, can be useful in determining optical loss budgets during your systems
design and maintenance.
The following instructions describe the typical installation procedure:
1. Connect the video source to the video input BNC connector on the transmitter unit.
2. Connect the video output cable to one of the two video output BNC connectors on
the receiver unit.
3. Terminate any unused BNC output connector at 75 Ohms.
4. Connect the fiber optic cable to the transmitter and receiver units.
5. Connect the Universal Power Supply to the transmitter and receiver units.
For box versions using DC power, please refer to figure 1.
6. When power is applied, the green POWER LED should illuminate, indicating the
presence of operating power. The 3G/HD/SD RATE LED will give an indication as
described in the Indicator LED’s and Alarm Circuitry section of this manual.
7. The system should now be operational.
Note: The Rack Card version has an additional red LED for indicating the presence of an alarm
condition (loss of signal). Refer to Indicator LED’s and Alarm Circuitry sections of this manual.
FiberLink® 3350 Series
3G/HD/SD-SDI Transmission over one single
mode or multimode fiber
INSTALLATION INSTRUCTIONS
Figure 1: Power Connector DC Input Polarity
9-24 Volts
AC or DC
(+) Positive
( - ) Negative
SDI Displays or
SDI Equipment
3350 Tx
3G/HD/SD-SDI
Source
3351 Rx
Fiber
Cable
Fiber
Cable
3350 Tx
3G/HD/SD-SDI
Source
3351 Rx
Fiber
Cable
3G/HD/SD-SDI
Loop-Thru
QUICK START GUIDE

2
CS208-003350-00_A
Additional information is available online at www.artel.com
ALARM SWITCH FOR TRANSMITTER CARD
Switch
Position
Alarm
Indication On Off
1Loss of Optical
Signal Enabled Disabled
2N/A N/A N/A
Note: The rack card unit also provides an output to drive a model 6020A
Alarm Sensing Module which provides an audible tone and activates a set
of contacts for external signaling purposes.
ALARM SWITCH FOR RECEIVER CARD
Switch
Position
Alarm
Indication On Off
1Loss of Input
Video Enabled Disabled
2N/A N/A N/A
INDICATOR LEDS
Transmitter LEDs
LED Status Definition
Power On Indicates correct power has been applied
3G Rate
O Indicates no 3G-SDI data rate lock
On Indicates 3G-SDI data rate lock at 2.97 Gbps or
2.97/1.001 Gbps
HD Rate
O Indicates no HD-SDI data rate lock
On Indicates HD-SDI data rate lock at 1.485 Gbps or
1.485/1.001 Gbps
SD Rate
O Indicates no SD-SDI or DVB-ASI data rate lock
On Indicates SD-SDI or DVB-ASI data rate lock at
270 Mbps
Alarm On Loss of input video (card version only)
Note: The 3G, HD, and SD LEDs indicators are o when a non-standard isgnal is
applied.
Receiver LEDs
LED Status Definition
Power On Indicates correct power has been applied
3G Rate
O Indicates no 3G-SDI data rate lock
On Indicates 3G-SDI data rate lock and re-clocked video
available on outputs
HD Rate
O Indicates no HD-SDI data rate lock
On Indicates HD-SDI data rate lock and re-clocked
video available on outputs
SD Rate
O Indicates no SD-SDI or DVB-aSI data rate lock
On Indicates SD-SDI or DVB-ASI data rate lock and
re-clocked video available on outputs
Alarm On Loss of optical signal (card version only)
Note: The 3G, HD, and SD LEDs indicators are o when a non-standard signal is
applied.
T: 978-263-5775
www.artel.com
[email protected]om
[e-mail]
Sales
FiberLink 3350 Series 3G/HD/SD-SDI over Fiber