ARTHUR HOLM DynamicCableRetract User manual

Mounting Instructions DynamicCableRetract
AHD2DOC01

Information
The DynamicCableRetract device is prepared to be mounted from
below the table.
A cover plate is supplied if the hole on the table can’t be made
properly or if aesthetically is required.
Included in all versions are all necessary brackets for the installation.
INTRODUCTION
2
Manipulation of the product should be avoided, no stress should be applied to the product except from the
instructions given in this document. Cutting, drilling, soldering, adding of electrical and mechanical
components can cause danger and should be avoided by all mean. Not complying with these direction will
result in a lost of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for any loss
or injury incurred as a result of modifications made to goods by anyone other than the supplier or the
supplier's authorised representative without the supplier's written permission. Such modifications shall be
deemed to terminate any further guarantee obligations. Compensation will not be paid for wages, loss of
profit, waste of time, packing and transport or any financial liability resulting from defects in the goods.
(Albiral Display Solutions shall not be liable for any loss or injury caused by negligence.)
ATTENTION

INFORMATION
Preparing the table 3
Cut a hole in the table surface
where the DynamicCableRetract
top surface will be installed.
Ensure that there is enough
space under the table to install
the DynamicCableRetract.
The output of the cable and
connections of the device are in
the back side (As shown in the
picture).
DynamicCableRetract Dimensions
Rear View Front View

INFORMATION
Preparing the table 4
CUT-OUT
If the cut-out in the table can’t be made with
precision, a Cover Plate is supplied in order to
hid the cut imperfections.
DynamicCableRetract can be installed in
tables with a thickness from 10mm [0,39] to
50mm [1.97]. For thickness over 50mm it will
be necessary to mill the lower part of the
table.
Top View
Bottom View

INFORMATION
Mounting Table Brackets 5
A jig is supplied in order to mark the holes and to make the installation easier.
1- Make the cut out according to
the provided pattern hole in the
table surface.
2- Place mounting jig in the table
bracket as indicated below.
Mounting Jig
3- From below the table, place the mounting jig with
the raised square into the already made cut out,
make sure the mounting jig is centred in the cut out.
4- Align the bracket with your table axis and mark the
screws position.Remove the mounting jig from the table
bracket.Mount the table bracket.
Front
Front
View from
below the table

Preparing the DynamicCableRetract 6
Place the brackets as shown in the drawing and tighten them down using the nuts (M4). Place the vertical
adjustment screws (2+2) in to the bracket so that the tip of the screw is flushed with the upper side of the bracket.
Bracket
(x4) M4 Nuts
(x4) M6X60 Vertical
Adjustment Screws
Bracket
DynamicCableRetract
Housing

Mounting the DynamicCableRetract 7
1- Place the DynamicCableRetract
housing with the brackets into the
installed table brackets as shown on the
drawing below. Insert the two M6 nuts.
2- Tighten each nut gradually until the
DynamicCableRetract top plate surface is flush with of the
table surface or cover plate:
-For the standard installation, flush the top plate surface
with the top surface of the table.
-For the installation with Cover Plate, place the Cover
Plate over the table surface and flush the top plate with
the top Surface of the Cover Plate.Do not stick the cover
plate at this moment.
Cover Plate
View from
below the table
View from
above the table

Cover Plate assembling 8
Before blocking, The DynamicCableRetract top
surface must be centered in the hole
ensuring that the perimeter has the same
separation on all 4 sides.
3- To level the device top surface of the
device with the table, screw the (x4)
M6x60 screws gradually.
There is a M6 screw in every corner, tighten one
more than others you can level the
DynamicCableRetract top surface with the top
surface of the table or Cover Plate.4- Tighten x4 M6 screws to block the device
Assembling with
Cover Plate

Cover Plate assembling 9
With the DynamicCableRetract is supplied a Cover Plate. This Cover Plate can help to hid the cut out of
the table if it can not be made properly. Follow next steps to stick the Cover Plate to top surface.
2- Remove the adhesive protection from
the back of the cover plate.
Cover Plate
Front
Front
3- Place the Cover Plate centered with respect
to the DynamicRetractableCalbe top plate
ensuring that the perimeter has the same
separation on all 4 sides.
1- Clean the table Surface where the Cover
Plate is goning to be taped.

www.arthurholm.com