Seville Classics Ultra HD 20247 User manual

ASSEMBLY INSTRUCTIONS
UltraHD® LED Lighted Workcenter
(Model No. 20247, 20246, 20157)
48 in. W x 24 in. D x 65.5 in. H
(1.21 m x 60.9 cm x 1.66 m)
Reference page 8 for special care and
maintenance of stainless steel
Granite Graphite Red
SC200304

Drawer
Top Cantilever Shelf
No. Qty. No. Qty.
#1 1PC #20-5 1PC
#2-C 1PC #20-6 1PC
#3-B 1PC #20-7 DRAWER DIVIDER 2PCS
#3-C 1PC #44 1PC
#5-B 2PCS #46-1 TOP CANTILEVER SHELF BACK PANEL 1PC
#6 4PCS #46-2 TOP CANTILEVER SHELF BASE PANEL 1PC
#18 1PC #46-3 TOP CANTILEVER SHELF LEFT PANEL 1PC
#18-1 TOP CANTILEVER SHELF MAT 1PC #46-4 TOP CANTILEVER SHELF RIGHT PANEL 1PC
#19-2 DRAWER BASE PANEL 1PC #47 "L" BRACKET 8PCS
#20-1 DRAWER FRONT PANEL 1PC #48-2 SMALL DRAWER LEFT SUPPORT 1PC
#20-3 DRAWER LEFT PANEL 1PC #48-3 SMALL DRAWER RIGHT SUPPORT 1PC
#20-4 DRAWER RIGHT PANEL 1PC #49 PEGBOARD LONG SUPPORT BAR 2PCS
DRAWER MAT
BOTTOM PEGBOARD PANEL
Parts
Parts
LEG PIECE
LED LAMP
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department (please refer to page 9.)
SOLID HARDWOOD BOARD TOP
TOP PEGBOARD PANEL
BOTTOM CROSSBAR
DRAWER BACK PANEL
DRAWER FRONT PANEL SUPPORT PLATE
LEVELING FOOT
1

No. Qty. No. Qty.
#15 36PCS #100 4PCS
#21 1PC #101 4PCS
#25 1PC #103 8PCS
#27-B 10PCS #104 2PCS
#40 10PCS #105 2PCS
#41 29PCS #106 2PCS
#45 1PC #107 1PCS
#50 48PCS
#51 4PCS
STUD SCREW J
4" CURVED DOUBLE PRONG
2" PLIER HOLDER
2" MULTI-TOOL HOLDER
POWER STRIP W. USB PORTS
1.5" STRAIGHT
2" DOUBLE PRONG
WRENCH
WASHER
1/2" CURVED
Parts
1" CURVED
Parts
SCREW B (M4 x 8L)
SCREW DRIVER
SCREW I (M6 x 15L)
SCREW F (M4 x 8L)
SCREW E(M8 x 18L)
#21
#25
#45
#100 #101 #103 #104
#105 #106 #107
2
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department (please refer to page 9.)
#15 #50 #27-B #40 #41 #51
M8X20 pcs

Step 1.
Step 2.
NOTE:
Step 3.
NOTE:
TIP: A magnetic screwdriver is included for convenience. If using a power screwdriver, keep torque setting LOW.
Install (#5-B) Leg Piece.
A: Open the package and make sure there are no missing parts. Set the parts aside. Then, attach the (#47) "L"
Bracket to the (#5-B) Leg Piece, use (#50) Screw I to tighten. Repeat Step A to install (#47) "L" Brackets to another
one (#5-B) Leg Piece.
Note: Tighten the all the screws after the (#47) Brackets are flush with the (#5-B) Leg Piece.
B: Leave the Solid Hardwood Board Top (#1) on cardboard to reduce the chance of scratching during assembly.
Attach the (#5-B) Leg Pieces to the back of the (#1) Solid Hardwood Board Top, line up the screw holes, use (#50)
Screw I and (#21) Screwdriver to tighten.
Install (#48-2) Small Drawer Left Support, (#48-3)
Small Drawer Right Support.
Attach the (#48-2) Small Drawer Left Support to the
bottom of (#1) Solid Hardwood Board, line up the screw
holes, use (#50) Screw I and (#21) Screwdriver to
tighten.
Repeat this step to install (#48-3) Small Drawer Right
Support.
Do not fully tighten the screws. This will help you
make any adjustments for alignment.
Install (#3-B) Bottom Cross Bar and (#6) Leveling
Feet.
Attach the (#3-B) Bottom Cross Bar to the back of (#5-B)
Leg Piece, line up the screw holes, use (#40) Screw E
with (#27-B) Washer and (#25) Wrench to tighten.
After installing (#5-B) Leg Pieces, attach (#6) Leveling
Feet to (#5-B) Leg Pieces, use (#25) Wrench to tighten.
Turn the workbench upright once you finish this step.
A
B
UltraHD® LED Lighted Workcenter (Model No. 20247, 20246, 20157)
*NOTE: We recommend using TWO people to assemble the workbench.
3
A
B

Step 4.
Step 5.
Step 6. Install (#46) Top Cantilever Shelf .
Step 7. Install Assembled (#46) Top Cantilever Shelf to
workbench.
Attach assembled (#46) Top Cantilever Shelf to (#2-C) Top
Pegboard Panel and (#49) Pegboard Long Support Bars, line up
the screw holes, use (#41) Screw F to tighten. Use (#15) Screw B
to fasten the (#2-C) Top Pegboard and (#46) Top cantilever Shelf.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
A). Attach the (#46-3) Top Cantilever Shelf Left Panel and the
(#46-4) Top Cantilever Shelf Right Panel to (#46-2) Top Cantilever
Shelf Base Panel. Use (#41) F screws to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
B). Make sure to slide the (#46-1) back panel underneath the
edge of (#46-2) Top Cantilever Shelf Base Panel. Use (#41) F
screws to tighten.
Install (#49) Pegboard Long Support Bar.
Attach (#49) Pegboard Long Support Bar to the back of the
workbench, line up the screw holes, use (#40) Screw E with (#27-
B) Washer to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Install (#3-C) Bottom Pegboard Panel and (#2-C) Top
Pegboard Panel.
Attach (#3-C) Bottom Pegboard Panel along the back top edge of
workbench and against (#49) Pegboard Long Support Bar, line
up the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten. Use (#15) Screw B to fasten the (#2-C) & (#3-C) Top &
Bottom Pegboard.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Attach (#2-C) Top Pegboard Panel to the top of (#3-C) Bottom
Pegboard Panel and (#49) Pegboard Long Support Bar, line up
the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten.
AB
4
UltraHD® LED Lighted Workcenter (Model No. 20247, 20246, 20157)
*NOTE: We recommend using TWO people to assemble the workbench.