Asada CLEAR SCOPE 2820 User manual

PIPE INSPECTION ENDOSCOPE
CLEAR SCOPE 2820
INSTRUCTION MANUAL
【Read through this manual carefully before using the device.】

CLEAR SCOPE 2820
2
SAFETY PRECAUTIONS
CLASSIFICATION OF CAUTIONS
Explosion
Electric
Shock
Do not
Disassemble
Fire
Burn
Handling of
Wire
Working
Condition
User’s
Manual
Others
Thank you for choosing our CLEAR SCOPE 2820.
●This Instruction Manual must be retained by the user of this device.
●Read this Instruction Manual carefully and completely before use and thoroughly
understand the usage, capacity, cautions and easy repairs for correct operation.
●After reading theinstructions, savethis manual sothat you can read it whennecessary.
●Use the device for the intended application only. It will do a better job and be
safer at the rate for which it was designed.
●Upon receiving the device, check the following.
· Check that the device is built conforming to the specifications stated in your order.
· Check the overall device for any damage or deformation caused in transit due to
accidents or other reasons.
· Check that all items and accessories delivered.
In case any discrepancy is found, immediately report the fact to the shop you purchased or our sale office.
(The contents of this manual are subject to change without priornotice.)
Precautionary signs are classified into the following 3 levels.
Indicates an immediately hazardous situation which, if not avoided, will result in
death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
SAFETY PRECAUTIONS.................................... 2
COMPONENTS OF THE DEVICE ................. 5
Main Parts.................................................................... 5
Specifications .............................................................. 6
Standard Accessories ............................................... 6
Button Operation List................................................. 7
PREPARATION ......................................................... 9
Transportation in Clear Scope Case ..................... 9
Charging Battery ...................................................... 10
Connection of Clear Scope and Camera Cable ..... 11
Installation & Removal of SD Card ...................... 12
HOW TO USE........................................................... 13
Installation of Monitor & Adjusting Angle ........ 13
Inserting Camera...................................................... 13
RECORD VIDEO..................................................... 15
Taking Image ............................................................ 15
Taking Video ............................................................. 15
Checking Image & Video………………………….15
Deleting Image & Video……………………………15
SETTING.............................................................................16
Deleting all files…..………………………...………..16
Video Output …………………………………………16
Setting Date/Time….……………………………….16
Language.…………………….……………………….17
Video Output Scheme …………………………….17
Auto Power Off……………………………………….17
Distance Counter……………………………………18
Image Rotation………………………………………18
Digital Zoom…..……………………………………….19
CONNECTING WITH OTHER DIVICES……..20
Connect to PC (Windows7/10）………………………..20
Connect to TV……………………………..……………..20
MAINTENANCE & INSPECTION ……………..21
BEFORE ASKING FOR REPAIRS ………...…
22
INDEX
WARNING
CAUTION
DANGER

CLEAR SCOPE 2820
2
SAFETY PRECAUTIONS
WARNING
◆Wear rubber (leather) gloves when you handle the Camera Cable.
You may have injuries on your hands as foreign material can adhere to the
Camera Cable during operation.
◆Do not operate the device in rain or with wet hands.
Operation in rain or with wet hands may lead to electric shock.
◆Do not use the device in an area where gasoline, thinner or any
other combustible gas may exist.
◆Do not use the device in a dusty area.
It may lead to explosion, heating or mechanical failure.
◆When unattended, blackout or servicing, switch off and unplug
the device.
◆During thunder, stop the operation and do not touch the device.
It may lead to electric shock.
◆Do not touch the Camera Head.
It is hot and you may get burned.
3
●Basic cautions to use the device safely are listed in this section.
●The detailed cautions in operation are described in each chapter.
◆Only qualified persons are allowed to disassemble the device.
◆Do not modify the device.
◆Use the device for the intended application only.
This device is designed to inspect inside various pipes. Do not use this device
for medical purposes or for inspection of aircraft and so on.
安
全
上
の
ご
注
意
DANGER

CLEAR SCOPE 2820
◆Do not let visitors touch the device.
◆Do not use the device when the result is unpredictable.
◆◆Do not overload the device.
It will lead to mechanical failure or an accident.
◆Keep your work bench and area tidy and well lit.
Bad working conditions invite an accident.
◆This device is a precision instrument.
Do not use or store in hot and humid conditions, in direct sunshine or
in vibrating conditions.
It may lead to mechanical failure.
◆Do not use the device near equipment which generate magnetism or
electromagnetic wave (such as microwave, TV, game machine and so on).
Strong magnetism from a digital circuit of TV, speaker, large motor,
and microcomputer may damage the record or may distort the picture image.
◆Do not operate the device when you cannot concentrate on your
work due to fatigue, drinking, medication and so on.
◆When not in use, the device should be stored in dry or locked up place
–out of reach of children.
◆Do not use the device for inspection of pipes for gasoline or chemicals.
It may lead to an accident or mechanical failure.
◆When cleaning, unplug the device and wipe it with a dry soft cloth.
If it is very dirty, wipe it with a tightly wrung out wet cloth and
then wipe it again with a dry cloth.
Do not use solvents such as thinner, alcohol or kitchen detergent which may deform
the external case or may remove the paint.
◆Depending on the object and/or the environment, the color on the display may
be different from the real one. It is due to the performance of the device
and not a trouble.
◆Use only the accessories or attachments given in this manual and our catalogs.
Otherwise it will lead to an accident or mechanical failure.
安
全
上
の
ご
注
意
CAUTION
4

CLEAR SCOPE 2820
◆Be careful not to drop or hit the device. Do not press the device hard.
If the device is subject to impact, stop operation and ask for repairs.
Otherwise, accident or injury can result.
◆Always check for deformation, corrosion and so on in each
part of the device.
◆Immediately stop the device if something is wrong with the
device (unusual smell, vibration, sound) and refer to “page 22
BEFORE ASKING FOR REPAIRS”. Do not disassemble the
device without reason and ask for repairs.
Contact our authorized distributors for repairs.
◆Do not look straight at the LED.
It may damage your eyes.
◆When the Display Unit is cold, the monitor may be darker than
usual. It will be improved once the Display Unit is warmed up.
◆The contents of the recording are not compensable.
Even if any failure in recording due to a trouble of the device or the SD card is
found, we are free from responsibility.
◆Keep the Display Unit away from sand, dirt, water and so on.
The Display Unit may be damaged when they enter inside.
安
全
上
の
ご
注
意
CAUTION
5

CLEAR SCOPE 2820
COMPONENTS OF THE DEVICE
Main Parts
If any label applied to the device has come off or has got dirty, always ask for a new label and
apply it in the original position.
Clear Scope RS-5
USB
SD Card
AV Terminal
Reset
AC Adapter
Camera Cable 2820
Reel Set
Camera Cable
2820
Mini USB Cable Video Cable
AC Adapter SD Card
Clear Scope Case for 2820
Coil Cable Cleaning Kit
製
品
の
構
成
6

CLEAR SCOPE 2820
Item
Code No.
PCE
Clear Scope RS-5
TH811
1
Camera Cable 2820
Reel Set
TH820
1
※Camera Cable 2820
TH812
1
※Clear Scope Case for
2820
TH814
1
Item
Code No.
PCE
Mini USB Cable
TH002
1
Video Cable
TH003
1
AC Adapter
TH755
1
SD Card
−
1
Coil Cable
TH813
1
Cleaning Kit
TH005
1
Instruction Manual
IM0504
1
Specifications
Item
CLEAR SCOPE 2820
Code No.
TH2820
Monitor
Size
5” colour LCD Monitor
製品の構成
Media
SD Card（Max 32GB）
Resolution
Image：307,200 Pixel（640 × 480）
Video：Mpeg 4（ASF：640 × 480）
Interface
AV output (NTSC/PAL) USB (Mass Storage)
Power
Li-polymer battery (internal)
AC Adapter (input: AC100V, output:DC5V)
Camera
Head
Applicable diameter
φ40㎜～φ100㎜
（For φ100㎜, Centering Guide is necessary）
Applicable bent pipe diameter
φ 40㎜ ～φ 100㎜
Outside diameter
φ 28㎜
Illumination
12 High Brightness LED
Visible angle
150°（Diagonal）
Focus area
5㎝～60㎝
Waterproof performance
Depth 10m
Camera
Cable
Outside diameter ×Length
φ 5.5㎜ × 20m
Minimum bent radius
110㎜
Waterproof performance
Depth 10m
Distance Counter
〇( Accuracy± (10cm+20%rd))
Temperature
Use・Storage
−20℃ ～ ＋60℃（No Condensation）
Charging
0℃ ～ +40℃（No Condensation）
Size
L350 × W300 × H380㎜
Weight
5.5kg
*Only the Camera and the Camera Cable are waterproof. The connecting part is not waterproof.
Standard Accessories
*Camera Cable 2820 & Clear Scope Case for 2820 are included in Camera Cable 2820 Reel Set.
7

CLEAR SCOPE 2820
Button Operation List
Below is a list of Button operation on each screen. (Monitor , Preview , Menu)
Button
Monitor
2019/05/01 17:22:40
00cm ×10
Can check and take an image, or record
a video.
▲
Display Preview
When an image is rotatable：rotate by ▼
▼
OK
Display Menu
ESC
Long press：Counter reset
Image
Take an image
Video
Start / Stop recording a video
−
Dim the LED light
+
Brighten the LED light
製
品
の
構
成
8

CLEAR SCOPE 2820
Preview
Menu
2019/05/01 17:22:40
Menu
Video output
Date/time setup
Language
Video format
Auto power off
製品の構成
00cm
Image
IMG00000
2019/05/01 17:22:40
00cm
Video
IMG00000
Can check and play back images and
videos.
Can change settings such as the date
Select and display the previous image
Proceed to the previous selection
Select and display the next image
Proceed to the next selection
Enlarge the selected image.
Select
Return to Monitor
Return to Monitor
Image：Display the next image
When a video is paused：take an image
Show the software version
Video：Play and stop
When setting date/time：Decrease a number
When setting date/time：Increase a number
※The pictures are image.
9

CLEAR SCOPE 2820
PREPARATION
◆Lock it securely.
Otherwise, the lid may open during
transportation and the device may
◆drop and be damaged.
Transportation in CLEAR SCOPE Case
①Put the device and the accessories properly in the case.
②Close the lid and lock it securely.
WARNING
◆Do not use the device in rain or in a location where water can enter inside
the device. Also do not use the device with wet hands.
It may lead to short circuit or electric shock.
◆Do not use the device in a dusty area.
It may lead to explosion, heating or mechanical failure.
Lock
準
備
CAUTION
10

CLEAR SCOPE 2820
CAUTION
◆Do not connect while the power
is on.
It may cause a damage.
Charging Battery
●Use the attached AC adapter for charging.
●The battery is not charged at the beginning. Charge the battery before using.
●It can be used for about 2 hours by charging for 3 hours. However, it depends on usage.
●If you leave the battery for a long time after fully charged, the battery might be damaged.
●The usage time of the battery becomes shorter as a charging frequency increases.
●Avoid frequent recharging for using the battery long time.
●If the battery lasts a short time despite being charged properly, it’s considered to have
reached the end of its life span. Replace the battery with a new one.
①Make sure that CLEAR SCOPE 2820 is turned
off.
②Charging will start when the unit is connected
to the outlet with AC adapter.
③Press the power button for 3-5 seconds to
turn on the power.
④Charging is complete when the three battery
marks don’t move.
The battery marks move while charging.
（）
※ The battery mark disappears after being
displayed for a few seconds.
To display the battery mark again, press ESC
button.
POWER
OFF
POWER
ON
⑤Connection
AC Adapter connection
④charge complete
（）
③Press 3-5sec.
準
備
11

CLEAR SCOPE 2820
Connection of CLEAR SCOPE and Camera Cable
① Make sure CLEAR SCOPE is switched off.
凹
③ Tighten
② Connect Coil Cable.
Align the marks on the connectors and put in straight.
③Tighten the screw.
④For disconnecting Coil Cable, loosen the screw
and pull out straight.
② put in straight
凸
◆Do not put in or remove the
connectors by force.
The connectors may be damaged.
◆Make sure the pins on the connector
are not deformed.
Ask for repairs when they are deformed.
OFF
POWER
◆Do not connect Coil Cable when the
device is switched on.
It may lead to mechanical failure.
準
備
CAUTION
CAUTION
12

CLEAR SCOPE 2820
◆Insert and pull out SD card when the power is switched off.
There is possibility to damage SD card and lose saved data.
◆ Do not insert other than SD card.
Insert mini SD and micro SD card to the unit after putting in special adaptor.
Contamination may cause of damage.
② Check direction of SD card and insert it fully till
hearing a sound.
*Without inserting fully, this may cause of
damaging SD card.
Caution for SD card
◆Do not power off when recoding and reading data.
There is possibility to damage SD card and lose saved data.
◆Avoid place SD card in high temperature and place where exposed by
direct sunlight and generate electromagnetic wave and static electricity.
◆Do not soak SD card in water and touch SD card in wet hands.
◆Avoid contamination, water and other particles on terminal point on back
of SD card. Do not touch this terminal by hands.
◆When disposing and transferring SD card, it is recommended that break
SD card physically or delete data completely by software of deleting data
for PC.
Format or delete function in this unit or PC cannot delete all the data.
◆Managing data in SD card is responsibility for customers.
Power
OFF
②Insert
check direction
を
Insert and Pull out SD Card
① Check that the power is switched off.
③ When pulling out SD card, push the card till
hearing sound and remove the card straightly.
準
備
Power O
OFF
③Press
to remove
押して取
出す
CAUTION
13

CLEAR SCOPE 2820
HOW TO USE
◆Do not insert Camera while
charging.
It may cause a trouble.
●Up on using, adjust the angle of the monitor to
watch well.
①Loosen the fixing knob and insert a ball on
back of the unit to the monitor arm of the cable
drum.
②Adjust the angle and tighten the fixing knob.
③ Take off the unit from the monitor arm and pack
in the case after use.
*The unit cannot be packed into the case with
the cable drum.
Insert Monitor arm
①Insert Camera slowly into the pipe to be inspected.
②When taking out Camera, pull out Camera Cable slowly.
After operation, rewind in Cable Reel wiping off water
and dirt on it.
Inserting Camera
Inserting Monitor / adjustment
Tight
Loose
Fixig knob
使
用
方
法
CAUTION
14

CLEAR SCOPE 2820
◆Do not pull the Camera Cable by force. The Camera Cable may be broken or bent.
◆Do not hold the Camera Cable at far distance from the insertion opening when
inserting Camera Cable.
If the Camera Cable is bent too much, it may be broken.
◆The minimum bent radius of the Camera Cable is
110mm. It will be broken when the bent radius is less than 110mm.
As the Camera Cable cannot be repaired, the broken cable should
be replaced with a new one which is charged. Pay much
attention for its handling.
◆Do not push the lens hard.
◆Do not leave the device keeping the lens pointed towards the sun.
It may be damaged due to light condensing. Be careful when the device is placed
outside or by the window.
◆Depending on the object and/or the environment, the color on the monitor
may be different from the real one or the image may not be clear.
It is due to the performance of the device and not a trouble.
◆The image may not be clear due to mist on the lens when used under
the conditions of different temperature.
◆The image may not be clear when the Camera is in water or liquid.
◆The image of the object is not clear when it is out of the focus area.
◆The image may be brighter or darker due to the automatic exposure function.
◆The image may be noisy to keep the brightness of the LCD Monitor under
low light condition or when the LED is dark.
◆Keep CLEAR SCOPE away from sand, dirt, water and so on.
The device may be damaged when they enter inside.
◆After use, remove the dirt and water on the Camera Cable and then close
the case in dry conditions.
CAUTION
15

CLEAR SCOPE 2820
RECORD
① Press the photo button to take a photo.
② Camera mark appears on the screen and
a photo is taken.
①Press the video record button to record a video.
On the screen, “REC”shows at the upper-
left and recording time at the lower-left.
②Press the video record button again to finish
recording and save a video.
Photo button
① Video record button
①Press ▲ or ▼mark on menu screen to show.
② Press ▲or ▼again to select data and press OK.
③Video mark on the upper-left on the screen indicates
video data. Press the video record button to preview.
Press again the video record button to pause the
video. Press the photo button at the paused video to
record the screen as a photo.
④Press ESC to back to monitor screen.
④ESC button
③Preview/Pause
① Press ▲or▼
①Press ▲ or ▼mark on in order to show preview
screen and show a data to be deleted.
②Press OK and confirm to a data to be deleted, then
press OK again to choose a data to be deleted.
③Press OK to delete a data.
②OK button
「Delete?」
▼ button
「OK」
③OK button
④「Delete」
Delete Photos and Videos
Check Recorded Photos and Videos
Take a photo
Record Video
映
像
を
記
録
す
る
16

CLEAR SCOPE 2820
SETTING
Video Output
●Press OK on monitor screen to show menu screen.
Delete all of the Data
Delete all of the recorded data.
①Choose “DELETE ALL”and press
OK.
②Select YES or NO for confirmation,
then press OK.
Press video output to show a data on TV or
other device.
*When showing data on TV or other device,
no data shows on the unit monitor.
Date Time Setup
Set date and time on the screen.
When date appears on screen, the data is also
indicated on a photo.
①Select “DATE/TIME SET TIME”and press OK.
②Press ▲ or ▼to select year/ month / day or
hour / minute/ second and press （＋）/ （－）
to increase and decrease the value.
③Press OK to confirm.
＊Press ESC to exit without setting.
設
定
17

CLEAR SCOPE 2820
Language
Set language (Japanese, English, German,
French, Spanish, Italy and so on)
①Select “Language”and press OK.
②Press ▲ or ▼to select language and press OK.
Video Format
When showing data on TV or video, select video
format (NTSC/PAL)
①Select “Video format”and press OK.
②Press ▲ or ▼to select and press OK to confirm.
Auto Power Off
Set a time of auto power off.
①Select “Auto power off”and press OK.
②Press ▲ or ▼to select and press OK to confirm.
設
定
18

CLEAR SCOPE 2820
Length measure
Show the distance of pulled camera cable.
①Select “Length measure”, press OK.
②Press “Reset”to clear the count to ZERO.
* Can be reset by keep pressing ESC button for a
few second.
③Select “Unit”to change the unit of
distance from CM, INCHI, M and FT.
⑤Select “Disable”or “Enable”to show the
distance on the monitor or not.
Photo Inversion
Invert a photo in monitor screen to see images
easier.
①Select “Rotation”and press OK.
②Select “Enable”and press OK.
③Back to monitor screen and press ▼
to turn image by 90degrees.
Length measure
Reset
Unit
Disable/Enable
設
定
Rotation
Disable
Enable
19

CLEAR SCOPE 2820
Digital Zoom
When setting digital zoom, Photo is zoomed
（× 1.0 ～2.0）on the monitor screen.
①Select digital zoom and press OK.
②Press ▲ or ▼to change magnification ratio.
See a zoomed photo in this condition.
設
定
20