ASG BTL-05 User manual

Electric Screwdrivers
BTL-05, BTL-10, BTL-15
DC 20/30 V
Instruction Manual
Please Read Instructions
Before Operating
Note
• Thiselectricscrewdriverisdesignedforindooruseonly.
Pleasedonotuseitoutdoorsorinawetenvironmentto
preventthedangerofelectrocution
• Payattentiontothevoltagespecication.Makesure
theswitchisintheOFFpositionwhenyouplugin
thepower
• Unlessyouareatrainedmaintenancepersonnel,donot
disassemblethedevicelestitcausesdangersormore
damages
Operating Instructions
• Makesurethepowerisswitchedofftoinstallorreplace
screwdriverbits;pressingthefront-endironcapwill
allowthescrewdriverbitstobeinsertedorreleased
• Itisrecommendedtosuspendtheelectricscrewdriver
byaexiblebalancerforeasyoperationandprevent
itsdropping
• Adjustthetorquedialtotheproperpositionaccording
tothedial/torquetableforeachmodel
• Theforward/reverseswitchshouldbesettotheforward
positionwhenfasteningscrews.Pressthestartswitch
tocompletetheoperation.Theautomaticcontrolmodel
willshutoffthepowerandstoptherotationofthe
screwdriverbitassoonasthesettorquevalueisreached
• Positiontheforward/reverseswitchtoreverseto
loosenscrews
• Usehandstoholdtheelectricscrewdriverduring
operation.Keepitinaperpendicularpositionwiththe
screwandapplypressureslightlytopreventslipping
• Usehandsorothermeanstoxtheobjectoperated
andoperatetheelectricalpowerscrewdriversafely
• Donotswitchtheforward/reversepositionwhenthe
motorisrunningtopreventtheshort-circuitofthe
startswitch
• Toensurelonglife,useitunderthenormaloperation
frequency(8workinghoursperdayandfasten800-
1000screwsperhour)
• Pleasedonotusethistypeofelectricscrewdriverto
fastenwoodenscrews
Regular Simple Maintenance
Checktoseewhetheralltheparts,shell,andpowerlines
areintactallthetimetoensurenormaloperations.Unplug
thepowerplugandturnoffthepowerbeforedoingany
maintenanceoperationtoensuresafety.Forevery1000
hoursoperationorhalfyear,thefollowingcleaningand
maintenanceoperationstothemachinebodyandtheinside
arerequired.
ON/OFF Switch
5P Connector
Trigger
Torque Adjusting
Nut
Forward/Reverse
Switch
Torque Dial
Bits Holder Collar
ON/OFF Switch
ON/OFFSwitchisonthehead
oftheelectricscrewdriver
ASG, Division of Jergens, Inc.
15700S.WaterlooRoad|Cleveland,OH44110-3898
Phone:(888)486-6163|Fax:(216)481-4519
Email:[e-mail]|Web:www.asg-jergens.com

Output Torque/Adjust Dial Soft Start Adjustable Time Setting Switch Power Supply
Usercanadjustoutput
torquerangeofthetoolvia
changingthetorquespring.
Pleaserefertothetorque/
dialtableandthenturnthe
“torqueadjustingnut”to
settheproperdialforeach
modelofmachineandset
tothedesiredtorquefor
operations.
TheBTL-05,BTL-10andBTL-15brushlesselectricscrewdrivers
possessSoftStartadjustabletimesettingswitch.Usercanset
themachinestostartfromlowerspeedfor0.2-4.0seconds
andthenswitchtofullspeedoperatingautomatically.
Withvelevelstochoose:0.0sec/0.5sec/1sec/2sec/4sec
Switching Power Supply
BTL-5A (65710)
Theadjustableswitchisat
thecorrespondingposition
insidethesquareopening.
Seetheredcircleonthe
rightpicture.
Turntheswitchseparately
tosetthetimeofSoftStart
Carefullytakeoffthetag
fromitsside,andusercan
seeasmallsquareopening
asthepictureshows.
Adjusting Torque
• Thedialsontheelectricscrewdriverdonotrepresentthe
torquevalue
• Pleaseusethetorque/dialtabletosettheproperdial
foreachdifferentmachinetypeandsettothedesired
torqueforoperations
• Actualtorqueoutputshouldalwaysbeveriedwitha
torquetester,suchastheASGDTTseries
• TheBTL-05,BTL-10andBTL-15brushlesselectric
screwdriverscanbeusedwithswitchingpowersupply
BTL-5A(65710)
• Theelectricscrewdriverconnectstothepowersupply
with5Pconnectingwire
• Insurethatthepowersupplyisconnectedat90-240V
50/60Hz,andturnonthepower
• ByturningtheHI/LOWswitch,usercanadjustthespeed
oftheelectricscrewdriver
• WhenusingthePS-55powersupply,thescrewcounter
STC-02andSoftStartfeaturewillnotfunction
Torque Adjusting
Nut
BTL-05
BTL-15BTL-10