Asgard Access User manual

ASGARD
'ACCESS'
PACK CONTENTS
ITEM
NO
PART
DESCRIPTION QTY
1
2
3
4
5
6
40966
BASE PANEL
1984*950 1
41329
LH SIDE PAN
1269*950
1
41341
LH BACK PNL
1269*961
1
1
41452
LH FRT PANEL
1075*250
1
1
7
8
40961
LID S/A
2056*1016
9
1
1
1
41348
LH DOOR SA
1064*702
10
11
12
M5x12 CSK
ZSCREW340
41459
HINGE SUPP PLT
41843
LH CORN BRACE
13
GAS STAY 400N
ZHWMISC89
12
4
1
2
ASGARD
ACCESS
SELF ASSEMBLY INSTRUCTIONS
PLEASE NOTE FOR SAFETY REASONS THE
ASSEMBLY OF THIS UNIT REQUIRES
TWO PEOPLE.
BASE INSTRUCTIONS
A FIRM, LEVEL ,FLAT SURFACE IS
REQUIRED AS A BASE FOR THIS UNIT
SUCH AS CONCRETE OR FLAGS.
- MINIMUM BASE MEASUREMENT
FOR ACCESS IS 2200*1150
- MINIMUM DISTANCE
FROM WALL IS 100
TOOLS REQUIRED
- POSI-DRIV SCREWDRIVER
(POWER DRIVER RECOMMENDED)
- 6mm DIA MASONRY DRILL
- 13mm SOCKET SPANNER
(FOR ANCHOR FIXINGS)
DOOR ALLIGNMENT & ANCHORING
OF UNIT
IT IS IMPORTANT TO CORRECTLY LEVEL
THE UNIT USING THE PACKING PIECES
PROVIDED, ONCE ASSEMBLY IN
ACCORDANCE WITH THE INSTRUCTIONS
OVERLEAF IS COMPLETE AND PRIOR TO
FIXING THE UNIT TO THE GROUND.
- SLIDE THE PACKING PIECES UNDER THE
CORNERS OF THE UNITS BASE AS
REQUIRED UNTIL AN EQUAL GAP HAS
BEEN ACHIEVED AROUND THE DOOR
ALLOWING FOR ITS SMOOTH
OPERATION & ALLIGNMENT.
- DRILL THROUGH THE FOUR HOLES
IN THE BASE OF THE UNIT USING
6mm DIA MASONRY DRILL TO A DEPTH
OF 70mm.
- SCREW IN THE ANCHOR FIXINGS.
(THESE HAVE A SELF CUTTING THREAD)
IF NOT ANCHORING THE UNIT USE
THE SELF SEAL PLUGS TO BLOCK THE
FIXING HOLES (FIT FROM UNDERSIDE)
PLEASE SEE OUR WEBSITE FOR DETAILS
OF MAINTENANCE OF THIS PRODUCT
WWW.ASGARDSSS.CO.UK
15
1
16
17
18
1
4
60
BLACK HANDLE
ZHWHANDLE32
M8 BALL STUD
ZSCREW42
SELF TAPPER
ZSCREW100
19
41457
HINGE FIX PLT
4
1
2
3
41331
RH SIDE PAN
1269*950
4
5
41342
RH BACK PNL
1269*961
6
7
41453
RH FRT PANEL
1075*250
8
9
10
41350
RH DOOR SA
1064*702 11
12
16
20
M5 LOCKNUT
ZHWNUT41 12
21
2mm SHIM
ZCOMPPLAS22
10
3mm SHIM
ZCOMPPLAS23
5mm SHIM
ZCOMPPLAS24
22
4
23 4
24 4
25
M7.5x60 BOLT
ZSCREW32 4
26
27
28
S/SEAL PLUG
ZCOMPPLAS02 4
PLASTIC BAG
ZBAGS08 2
INSTRUCTIONS
Z41467 1
16
14 41844
RH CORN BRACE 1
13
14
15
15
41824
LOCK SHROUD 229
M5x12 PAN
ZSCREW43

Z
AA
BB
DD
SS
PARTS INSTRUCTION
RH BACK - 5
BASE - 1
POSITION RH BACK '5' UP TO BASE PANEL '1'
ENSURING HOLES ARE ALIGNED AND THAT
THE BACK CENTRAL FOLD IS POSITIONED IN
THE CUTOUT SLOT IN THE BASE.
THIS PANEL REQUIRES SUPPORT WHILST
SCREWING PANELS TOGETHER.
3*
PARTS INSTRUCTION
LH BACK - 4
POSITION THE LH BACK '4' UP TO THE PRE
ASSEMBLED BACK AND BASE ENSURING ALL
HOLES ARE ALIGNED, SCREW TOGETHER.
PARTS INSTRUCTION
10*
LH SIDE - 2
16*
LOCATE LH SIDE PANEL '2' TO THE BASE AND
LH BACK AS SHOWN ENSURING THAT HOLES
ARE ALIGNED.
LOCATE RH SIDE PANEL '3' TO THE BASE AND
RH BACK AS SHOWN ENSURING THAT HOLES
ARE ALIGNED.
SCREW TOGETHER ALONG THE BASE AND
VERTICAL JOINT.
LH FRONT - 6
PARTS INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION
INSTRUCTION PARTS
PARTS
PARTS
PARTS
STEP 1 STEP 2 STEP 3 STEP 4
STEP 5 STEP 6 STEP 7
14*
CORN BRACE
LH - 13
RH - 14
LOCATE CORNER BRACE '14' TO THE
UNDERSIDE OF RH SIDE PANEL '3' &
RH FRONT PANEL '7'
LOCATE CORNER BRACE '13' TO THE
UNDERSIDE OF LH SIDE PANEL '2' &
LH FRONT PANEL '6'
12* 12*
NOTE A SCREW IS ONLY REQUIRED IN ALL
THE OBROUND HOLES. THE 4 ROUND HOLES IN
EACH OF THE LH & RH BACKS ARE FOR SHELF
BRACKETS WHICH ARE PURCHSED SEPERATLY.
BOTH PANELS REQUIRES SUPPORT WHILST
SCREWING PANELS TOGETHER.
1
5
4
RH SIDE - 3
2
3
6
7
RH FRONT - 7
LOCATE LH FRONT PANEL '6' TO THE BASE AND
LH SIDE AS SHOWN ENSURING THAT HOLES
ARE ALIGNED.
LOCATE RH FRONT PANEL '7' TO THE BASE AND
RH SIDE AS SHOWN ENSURING THAT HOLES
ARE ALIGNED.
SCREW TOGETHER ALONG THE BASE & AND
VERTICAL JOINT. VERY IMPORTANT YOU MUST
PUT THE SCREWS IN THROUGH THE CLEARANCE
HOLES IN THE BASE ALL 14 SCREWS MUST BE
USED
SCREW CORNER BRACE TO PANELS
FROM UNDERSIDE
9
10
LH DOOR - 9
RH DOOR - 10
WE RECOMMEND THAT YOU USE HAND HELD
DRIVERS RATHER THAN POWER DRIVERS
WHEN FIXING THE DOORS.
IT IS IMPORTANT TO SUPPORT THE DOOR
AT ALL TIMES WHEN FITTING THE SCREWS
TO ENSURE CORRECT ALIGNMENT AND SO
NOT TO DAMAGE THE THREADED INSERTS.
7
3
UNDERSIDE
26
2-OFF 5mm SQ HOLES
DENOTES RH BACK
3-OFF Ø6.4 HOLES
DENOTES LH BACK
14
ITEM 18 ITEM 18 ITEM 18 ITEM 18
ITEM 18 ITEM 19
CLEARANCE HOLES
IN BASE
8
17
LID - 8
FIT M8 BALL STUD PART No17
TO LID AT BOTH SIDES
ITEM 17
2*

JJ
RR
PARTS INSTRUCTION
2*
PARTS INSTRUCTION PARTS INSTRUCTION
12*
PARTS INSTRUCTION
INSTRUCTIONPARTS
STEP 8 STEP 9 STEP 10
STEP 11
2*
HINGE FIX
PLATE - 11
HINGE SUPP
PLATE - 12
VERY IMPORTANT THIS IS A 2 PERSON OPERATION
LIFT LID ONTO THE TOP OF THE UNIT
4-OFF
4-OFF
1 PERS OUTSIDE WITH HINGE FIX PLATE 11
1 PERS INSIDE WITH HINGE SUPP PLATE 12
PUSH PLATES TOGETHER TRAPPING HINGE
BETWEEN BACK PANEL & FIXING PLATES &
FIX WITH M5 NYLOCK NUT
ITEM 17 ITEM 22
11
12
16
THIS IS A 2 PERSON OPERATION
GAS STAY
400N - 16
ITEM 16
GAS STAY MUST BE FITTED WITH
THE SMALL Ø ROD POINTING
DOWNWARDS AND FIXED TO THE
SIDE PANEL & THE THICK Ø ROD
POINTING UPWARDS AND FIXED
TO THE TOP PANEL
THE GAS STAY CLIPS INTO
M8 BALL STUD ITEM 17
2
LH SIDE - 2
RH SIDE - 3
17
FIT M8 BALL STUD PART No17
TO LH SIDE PANEL PART No2
& RH SIDE PANEL PART No3
PARTS INSTRUCTIONS
HANDLE -26
ITEM 20
2*
CLIP WINGS BACK ON HANDLE
POSITION TO LID INLINE WITH
NUTSERTS & SCREW TOGETHER
USING 2-OFF M5x12 PAN HEAD
ITEM 20
STEP 12
2 LH
3 RH
8
VERY IMPORTANT
TO ENSURE SMOOTH OPERATION OF PADLOCK IT IS CRITICAL
THAT THE LOCK LOCATION HOLES ARE CORRECTLY ALIGNED.
THIS IS ACHIEVED THROUGH PRECISE LEVELLING OF THE UNIT
USING PLASTIC PACKING PIECES PROVIDED.
CHECK BOTH PADLOCKS WORK CORRECTLY BEFORE
UNIT IS SECURED TO FLOOR & SHROUDS ARE FITTED.
PARTS INSTRUCTIONS
LOCK
SHROUD
2-OFF
PART 15
15
ITEM 20
8*
LH SIDE - 2
RH SIDE - 3
LID - 8 FIT SHROUDS AT
BOTH SIDES OF
UNIT USING 8-OFF
M5x12 PAN HEAD
POZI SCREWS
VERY IMPORTANT
ENSURE LOCK OPERATES SMOOTHLY
BEFORE FITTING SHROUDS
INCORRECT ALIGNMENT CAN DAMAGE
THE KEY IN THE LOCK

B ( 0.25 : 1 )
C ( 0.18 : 1 )
B
Parts List
ITEM COSTDESCRIPTION
PART NUMBER
QTY
ITEM
LH SHELF BRKT04005921
RH SHELF BRKT04006022
SHELF SA04188923
Parts List
ITEM COSTDESCRIPTION
PART NUMBER
QTY
ITEM
M5 X 12 RHD BZPZSCREW438
5
Parts List
ITEM COSTDESCRIPTION
PART NUMBER
QTY
ITEM
No 10 x 5/8 S/TAP
ZSCREW1008
4
ASGARD ACCESS
SHELF ASSY INSTRUCTIONS
1. SCREW LH & RH SUPPORT
BRACKETS IN POSITION INTO
PRE DRILLED HOLES IN UNIT
USING 2 - ZSCREW100 SELF TAPPER
POZI SCREWS PER BRACKET
ZSCREW100 - 8-OFF
ZSCREW43 - 8-OFF
2
1
3
RH BRACKET AS SHOWN
LH BRACKET OPPOSITE
SHELF - BE CAREFUL WHEN
FITTING AS THE SHELF CAN
ONLY BE FITTED ONE WAY 2. POSITION SHELF ON TOP OF
BRACKETS & SCREW TOGETHER
USING 4 - ZSCREW43 M5x12 P/HD
POZI BZP SCREWS. THIS SHELF IS
NOT SYMETRICAL
DWG No 041983
SHELFS CAN BE FITTED ON
RH OR LH SIDE OF THE UNIT

A ( 0.60 : 1 ) B ( 0.60 : 1 )
DRG.No.REV.
DATE INT. REVISIONS
DRAWN BY DATE SCALE
MATERIAL
TOLERANCES:
` 0.5 mm. UNLESS STATED OTHERWISE
IF IN DOUBT - ASK
DO NOT SCALE
THIRD ANGLE PROJECTION
The Office Furniture Centre,
1392 Leeds Road,
Bradford BD3 7AE.
Tel: [phone] Fax: [phone]
PROJECT
DESCRIPTION
DRAWING No. REV.
Thecontents,information&copyrightofthis documentarethesole propertyofFLEXIFORMBUSINESSFURNITURELIMITED
andmustnotbeusedorcopied,eitherin partorwhole,withouttheexpresspermissionoftheownersin writing.
HD CHAIN BRACKET FIXING
INSTRUCTIONS
041977 R0
NeilH 06/05/2009 1:4
041977R0
ASGARD
A
Parts List
ITEM COSTDESCRIPTION
PART NUMBER
QTY
ITEM
BASE SA11
HD CHAIN BRACKET1
2
B
1
2
HD CHAIN BRACKET - POSITION VERTICAL HD CHAIN BRACKET - POSITION HORIZONTAL
FIXING INSTRUCTIONS
PLACE BRACKET ON BASE WHERE REQUIRED
EITHER VERTICAL OR HORIZONTAL
MARK HOLES THROUGH ONTO BASE WITH MARKER PEN
FOLLOW FITTING INSTRUCTIONS FOR DRILLING THAT COME
WITH THE HD CHAIN BRACKET
VERY IMPORTANT - HOLES THAT HAVE
JUST BEEN DRILLED IN BASE MUST BE
REPAINTED WITH A SUITABLE EXTERIOR
QUALITY PAINT TO PREVENT RUSTING
OF THE BASE PANEL
FOLLOW FITTING INSTRUCTIONS FOR FIXING THE
HD CHAIN BRACKET