Assa Abloy SW200 User manual

Owner's Manual
Swing Door Operator
ASSA ABLOY SW200
ASSA ABLOY Entrance Systems

CONTENTS - Original instructions
3Instructions for safe operation .......................................................................................................
4Congratulations on your new automatic door! ........................................................................
4Electronic equipment reception interference ...........................................................................
4Environmental requirements ..........................................................................................................
4Product liability ...................................................................................................................................
5Warranty ................................................................................................................................................
5Service .....................................................................................................................................................
6Intended use .........................................................................................................................................
6Technical specification ......................................................................................................................
6How the ASSA ABLOY SW200 works ............................................................................................
7ASSA ABLOY SW200 Variations ......................................................................................................
8Regular safety checks .........................................................................................................................
15General accessories ............................................................................................................................
15Safety accessories ................................................................................................................................
15Troubleshooting ..................................................................................................................................
16Service/Maintenance .........................................................................................................................
16Other products from ASSA ABLOY Entrance Systems .............................................................
ASSA ABLOY as word and logo are trademarks owned by the ASSA ABLOY Group
©ASSA ABLOY Entrance Systems, 2018
Technical data subject to change without notice.
Backtrack information: folder:Workspace Main, version:a454, Date:2018-03-27 time:03:25:24, state: Frozen
1007717-en-US-3.0Issue 2018-03-282

Instructions for safe operation
•Failure to observe the information in this manual may
result in personal injury or damage to equipment.
•To reduce the risk of injury to persons - use this oper-
ator with single or double pedestrian swinging or
folding doors only.
•Do not use the equipment if repair or adjustment is
necessary.
•Disconnect supply when cleaning or other mainte-
nance is to be carried out.
•The operator can be used by children over 8 years of
age if they have been instructed by a person in charge
of their safety.
•The operator can be used by children 8 years of age
or younger if they are supervised by a person respon-
sible for their safety.
•The operator can be used by persons with impaired
physical, sensory or mental capacity if they have been
instructed by a person in charge of their safety.
•Cleaning and user maintenance shall not be made by
children.
•Do not let anyone climb on or play with the door or
the fixed/remote controls.
•The doorset can be operated automatically by sensors
or manually by activators. It can also be used manually
as a door closer.
3Issue 2018-03-281007717-en-US-3.0

Congratulations on your new automatic door!
ASSA ABLOY Entrance Systems has developed automatic doors for more than 50 years. State-of-the-
art technology and carefully tested materials and components provide you with a superior product.
As with all other technical products, your automatic door requires periodic maintenance and service.
It is essential that you know your automatic door (system) and that you recognize the importance
of maintaining it in compliance with applicable standards for safety.
Your local ASSA ABLOY Entrance Systems-authorized representative is familiar with these standards,
as well as all applicable local codes and ASSA ABLOY Entrance Systems recommendations for power-
operated pedestrian doors. Service and adjustments performed by your ASSA ABLOY Entrance
Systems-authorized representative, will ensure safe and proper operation of your automatic door
unit.
Electronic equipment reception interference
The equipment may generate and use radio frequency energy and if not installed and used properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Re-orient the receiving antenna.
•Relocate the receiver with respect to the equipment.
•Move the receiver away from the equipment.
•Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
•Check that protective earth (PE) is connected.
If necessary, the user should consult the dealer or an experienced electronics technician for additional
suggestions.
Environmental requirements
ASSA ABLOY Entrance Systems products are equipped with electronics and may also be equipped
with batteries containing materials which are hazardous to the environment. Disconnect power
before removing electronics and battery and make sure it is disposed of properly according to local
regulations (how and where) as was done with the packaging material.
Product liability
According to regulations, the following are the responsibility of the owner or caretaker of the
equipment
•that the equipment operates correctly, so that it gives sufficient protection in regard to safety
and health
•that the equipment is operated and regularly maintained, inspected and serviced by someone
with documented competence in the equipment and in applicable regulations
•that the provided “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
(PRA-0007) are kept available for maintenance and service records
•that inspection covers the emergency opening function (when applicable)
•that the closing force is appropriate for the door size on fire-approved door systems (when ap-
plicable)
1007717-en-US-3.0Issue 2018-03-284

Warranty
ASSA ABLOY Entrance Systems warrants its products to be free from defects in material and work-
manship under intended use and service for a warranty time of 12 months, beginning at time of
delivery. This warranty extends only to the original buyer of the equipment.
ASSA ABLOY Entrance Systems warrants that the software will operate substantially in accordance
with its functional descriptions and that it has been recorded on non-defective media.
The ASSA ABLOY Entrance Systems warranty does not apply to
•That the software will be error-free or operate without interruption
•General wear and tear on the system
•Fuse, disposable batteries and glass damage
•System deviations caused by installer other than ASSA ABLOY Entrance Systems
•System that has been altered or damaged by vandalism or misuse
•System that has been additionally equipped with non-ASSA ABLOY Entrance Systems original
branded parts and/or spare parts
•Unrequired visits due to poor client communication (door working when our technician arrives,
reset, power discontinuation)
•Adjustments (closing and opening speed and also detection field radars) due to customer re-
quests (excludes operational adjustments thought to create a hazard)
•Water damage
•Adverse weather conditions
•Any damage caused, directly or indirectly, by a circumstance beyond the control of the applicable
company within ASSA ABLOY Entrance Systems, such as industrial dispute, fire, natural disaster,
war, extensive military mobilization, insurrection, requisition, seizure, embargo, restrictions in
the use of power and defects or delays in deliveries by sub-contractors caused by any such cir-
cumstances
Please note:
•Non-compliance with manufacturers care and maintenance recommendations may void the
warranty.
•ASSA ABLOY Entrance Systems-authorized resellers shall extend this warranty to end-users only,
but have no authority to extend a greater or different warranty on behalf of ASSA ABLOY Entrance
Systems.
•A service agreement with ASSA ABLOY Entrance Systems will help secure the availability of a
fully operational system and will give priority at call-out, thus minimizing the time that the
equipment is unusable.
Service
Inspections should be done regularly by a trained and qualified person. The frequency of these
inspections should be according to national regulations (or according to industry standard if
there are no national regulations). This is especially important when the installation concerns
a fire-approved door or a door with an emergency-opening function. To extend the life of your
investment and ensure safe and reliable operation of the door, we recommend a minimum
of 2 visits per year or more, depending on usage and operating conditions. Environmental as-
pects shall also be considered.
5Issue 2018-03-281007717-en-US-3.0

As your entrances are part of your business flow, there’s every reason to keep
them working well. ASSA ABLOY Entrance Systems offers you a maintenance and
modernization expertise to rely on. Our Maintenance Programs and Modernization
Services for entrance automation is backed by a extensive expertise for all types
of pedestrian- and industrial door and docking systems, independent of brand.
At your disposal is a team of dedicated expert technicians, proven through decades
of maintenance, service and satisfied customers.
Intended use
The door is designed to offer continuous use, a high degree of safety and maximum lifetime.
The ASSA ABLOY SW200 is an automatic swing door operator developed to facilitate entrances to
buildings and within buildings.
The ASSA ABLOY SW200 is a combination of a Heavy Duty (HD) operator for large heavy doors as
well as an low energy electromechanical operator (LE), mainly suitable for almost all types of internal
swing doors - but also external doors. This operator will be mainly used in the health care sector.
The ASSA ABLOY SW200 swing door operator can be combined with a full range of sensor products
providing swing door safety.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and to
minor friction changes caused by e.g. dust and dirt.
For escape in emergency situations the doorset is opened manually.
For installation and maintenance see Installation and Service manual 1007718.
Technical specification
ASSA ABLOY Entrance SystemsManufacturer:
1900 Airport Road, Monroe, NC 28110, USAddress:
ASSA ABLOY SW200Type:
120 V AC +10/-15%, 50/60 HzMains power supply:
Max. 300 WPower consumption:
The ASSA ABLOY SW200 complies with ANSI/BHMA.Standards:
How the ASSA ABLOY SW200 works
The swing door operator ASSA ABLOY SW200 uses a DC motor which is connected to the output
shaft by a combination of a bevel gear and spur gears. The arm system that is connected to the output
shaft opens the door in a wall mounted application.
There is also an adjustable spring mechanism connected to the output shaft. During opening of the
door, the clock spring is tensioned by the rotation of the output shaft. During the closing cycle, the
accumulated spring force is acting in the closing direction. The spring force can be adjusted so there
is appropriate force to close the door when it is operated manually or in case of a power failure.
To activate the operator you can use a manual activator (elbow switch) or an automatic activator
(radar device). It is also possible –where local standards allow –to activate the operator by just
pushing the door, if Push & Go is selected.
After the door has been activated it will open and stay open for a specified Hold Open Time (HOT).
When the HOT has elapsed the door will close.
The ASSA ABLOY SW200 can be set in three or four different modes, depending on optional pro-
gramme selector type, see table below.
In fully manual use (or in case of a power failure) the ASSA ABLOY SW200 acts as a normal door
closer.
1007717-en-US-3.0Issue 2018-03-286

FunctionPosition
The door is closed. The door cannot be opened with inner and outer activation
units. The door is locked if an electromechanical locking device has been fitted.
The door can be opened with a key switch (if fitted).
OFF
Passage from inside only. The door is normally locked if an electromechanical
locking device has been fitted. The door can only be opened with the inner acti-
vation unit and with a key switch (if fitted).
EXIT
The door can be opened with the inner and outer manual and/or automatic ac-
tivators. The electric strike, if fitted, is open.
AUTO
Normal
position
The door is held permanently open by the motor.OPEN
ASSA ABLOY SW200 Variations
Surface applied application in 5 1/8”Wide x 4 15/16”high headerASSA ABLOY SW200 -SA:
Surface applied application in 6”Wide x 6”high headerASSA ABLOY SW200 -SA-
6X6:
OHC application in 6”Wide x 6”high headerASSA ABLOY SW200 -OHC:
OHC Offset Pivot application in 6”Wide x 6”high headerASSA ABLOY SW200 -OS:
OHC Fold application in 6”Wide x 6”high headerASSA ABLOY SW200 -Fold:
OHC Bottom Load application in 6”Wide x 6”high headerASSA ABLOY SW200 -BL:
7Issue 2018-03-281007717-en-US-3.0

Regular safety checks
To help you fulfil the national/international requirements and to avoid malfunction and risk for injuries,
we have provided the following checklist.
Do not use if repair or adjustment is necessary.
If problem oc-
curs
Daily Action
Activate your operator and check visually, fastening and any damage of
•operator
1
•arm system
2
•position switch
3
•hinges
4
•door and glass
5
Also inspect your operator and check visually for
•sharp edges on the door leaf and door frame (if any)
6
•condition of door seals
7
•finger protection
8
•pivot
13
•and finally that the complete door runs properly and closes slowly in a smooth way
Set the programme selector in OFF mode and check that the operator and lock work together. Also check
that the lock really secures the door
9
.
Activate the manual activation units
10
if any, and walk towards the door. Check that the door has opened
sufficiently while you pass the entrance/exit.
Then proceed with the automatic activation units
11
in the same way.
Check the non-monitored safety sensors
12
if any, by standing in the swing path and activate the operator.
The door must not hit you when opening nor when closing. If you are unsure of which type of sensor you
have, please contact your ASSA ABLOY representative.
Set the programme selector in AUTO mode. Push the door manually in es-
cape direction and make sure that no object or function will prevent the
door from opening. Also make sure the escape route is free for use.
By law, these tests must be performed regularly by trained personnel.
Escape
doors
Let the door close after an impulse and make sure that no object will prevent
the door from closing and locking (if demanded).
Fire doors
See page 10 for more information about safety checks.
Contact your ASSA ABLOY representative. For contact information, see last page.=
Take appropriate measures.=
1007717-en-US-3.0Issue 2018-03-288

FUNCTION AND VISUAL INSPECTION
5
6
9
11
7
12
8
4
1
2
FUNCTION
ON
OFF HOLD
10
POWER
ON
OFF
3
13
Surface Applied shown
CLEANING
The best way to remove dust and dirt from the ASSA ABLOY SW200 is to use water and a soft cloth or a sponge.
A gentle detergent may be used. To maintain the quality of the surface treatment, the surfaces should be cleaned
once/four months period. The cleaning should be documented. To avoid damages to the profiles the brushes/weather
stripping must be vacuum-cleaned weekly.
•Do not expose windows, doors or profiles to alkalis. Both aluminium and glass are sensitive to alkalis.
•Do not clean with high pressure water. Operator, programme selector and sensor may be damaged and water may
enter the profiles.
•Do not use polishing detergent.
•Do not scrub with materials like Scotch-brite, as this will cause mechanical damage.
9Issue 2018-03-281007717-en-US-3.0

DAILY SAFETY CHECK
Perform these safety checks daily on each automatic swinging door to ensure your customers’safety and your own protection.
If safety sensor is not working, door may swing at you without stopping.
Motion Detector Actuation/Presence Detection Safety

Page 6 Issued: 10-4-2011 Besam SW200i
Daily Safety Check – Swing Doors
Perform these safety checks daily on each automatic swinging door to ensure your customers’ safety and
your own protection:
Motion Detector Actuation/Presence Detection Safety
1. Check electronic sensor by walking toward the door
opening. The door should start opening when you are
about four feet from the door, and should swing open
smoothly and stop without impact. Walk slowly
through the door, (about 6 inches per second) the
door should remain open.
2. Step out of the sensor zone. After a brief time delay
(at least 1½ seconds), the door should close to 10
degrees from fully closed, then noticeably slow down
and take at least 1½ seconds for the final 10 degree
closing.
3. Approach the safety side of the door first, then have
someone else approach the activating side of the
door. As long as you are in the safety area of the
door, it should not open. (See Figure 1)
Caution: If safety sensor is not working, door may
swing at you without stopping.
Floor Mat Actuation/Floor Mat Safety
1. Step on the opening mat.
2. It is necessary to have a safety mat covering the
entire area the door swings over. Step through the
doorway onto the safety mat and remain motionless
for four seconds. The door should remain open.
Repeat at several locations on the mat. (See Figure
2.)
3. Step off the safety mat. After a brief time delay (at
least 1 ½ seconds) the door should close to 10
degrees from fully closed, then slow down. The last
10 degrees of closing should be noticeably slower (at
least 1 ½ seconds).
4. With the door closed, step on the safety mat. Have
someone step on the opening mat. Door should
remain closed as long as someone remains on the
safety mat.
Caution: If safety sensor is not
working, door may swing at you
without stopping.
Check electronic sensor by walking toward the door opening. The door
should start opening when you are about four feet from the door, and
should swing open smoothly and stop without impact. Walk slowly
through the door, (about 6 inches per second) the door should remain
open.
1
Step out of the sensor zone. After a brief time delay (at least 1½ sec-
onds), the door should close to 10 degrees from fully closed, then no-
ticeably slow down and take at least 1½ seconds for the final 10 degree
closing.
2
Approach the safety side of the door first, then have someone else ap-
proach the activating side of the door. As long as you are in the safety
area of the door, it should not open, see Figure 1.
3
Floor Mat Actuation/Floor Mat Safety

Page 6 Issued: 10-4-2011 Besam SW200i
Daily Safety Check – Swing Doors
Perform these safety checks daily on each automatic swinging door to ensure your customers’ safety and
your own protection:
Motion Detector Actuation/Presence Detection Safety
1. Check electronic sensor by walking toward the door
opening. The door should start opening when you are
about four feet from the door, and should swing open
smoothly and stop without impact. Walk slowly
through the door, (about 6 inches per second) the
door should remain open.
2. Step out of the sensor zone. After a brief time delay
(at least 1½ seconds), the door should close to 10
degrees from fully closed, then noticeably slow down
and take at least 1½ seconds for the final 10 degree
closing.
3. Approach the safety side of the door first, then have
someone else approach the activating side of the
door. As long as you are in the safety area of the
door, it should not open. (See Figure 1)
Caution: If safety sensor is not working, door may
swing at you without stopping.
Floor Mat Actuation/Floor Mat Safety
1. Step on the opening mat.
2. It is necessary to have a safety mat covering the
entire area the door swings over. Step through the
doorway onto the safety mat and remain motionless
for four seconds. The door should remain open.
Repeat at several locations on the mat. (See Figure
2.)
3. Step off the safety mat. After a brief time delay (at
least 1 ½ seconds) the door should close to 10
degrees from fully closed, then slow down. The last
10 degrees of closing should be noticeably slower (at
least 1 ½ seconds).
4. With the door closed, step on the safety mat. Have
someone step on the opening mat. Door should
remain closed as long as someone remains on the
safety mat.
Caution: If safety sensor is not
working, door may swing at you
without stopping.
Step on the opening mat.1
It is necessary to have a safety mat covering the entire area the door
swings over. Step through the doorway onto the safety mat and remain
motionless for four seconds. The door should remain open. Repeat at
several locations on the mat, see Figure 2.
2
Step off the safety mat. After a brief time delay (at least 1 ½ seconds)
the door should close to 10 degrees from fully closed, then slow down.
The last 10 degrees of closing should be noticeably slower (at least 1 ½
seconds).
3
With the door closed, step on the safety mat. Have someone step on
the opening mat. Door should remain closed as long as someone re-
mains on the safety mat.
4
1007717-en-US-3.0Issue 2018-03-2810

DAILY SAFETY CHECK

Besam SW200i Issued: 10-4-2011 Page 7
5. Check the mat molding and threshold. It should be
complete and secured with all required screws.
6. If the door has motion detector activation and floor
mat safety, one of the following three requirements
must be met, (see Figure 3).
Five inches of visible safety mat must extend
through the door opening onto the approach side.
Provide a photoelectric (door hold open beam)
across the door opening on the approach side.
The adjustable time delay in the door operator
must be set to at least 4 seconds.
7. Do Not move very heavy objects over floor mats.
General Safety
1. Breakout Stop - In-swing doors on center pivots can
be supplied with a breakout stop that will allow the
door to open to 90 degrees in the opposite direction
of normal traffic. Call your supplier for details.
When the door is pushed into the breakout mode, the
power to the operator is removed, (except spring
closer force).
2. Decals – The door should have traffic decals properly
displayed as follows:
An arrow sign (see Figure 4) shall be visible from the
approach side of a swinging door, mounted on the
door at a height of 585 inches (14713 cm)
from the floor to the centerline of the sign. The
sign shall be minimum of 6 inches (15.2 cm), in
diameter, having a green circle surrounding a
black arrow on a white background.
An international DO NOT ENTER sign (see
Figure 5) shall be visible from the side that
would swing toward pedestrians attempting to
travel in the wrong direction. It should be
mounted on the door at a height of 585inches
(14713 cm), from the floor to the centerline of
the sign. The sign shall be minimum of 6 inches
(15.2 cm) in diameter, having a red circle with
the wording, Do Not Enter, in white letters.
Check the mat molding and threshold. It should be complete and se-
cured with all required screws.
5
If the door has motion detector activation and floor mat safety, one of
the following three requirements must be met, see Figure 3.
•Five inches of visible safety mat must extend through the door
opening onto the approach side.
•Provide a photoelectric (door hold open beam) across the door
opening on the approach side.
•The adjustable time delay in the door operator must be set to at
least 4 seconds.
6
Note: Do Not move very heavy objects over floor mats.
11Issue 2018-03-281007717-en-US-3.0

GENERAL SAFETY

Page 8 Issued: 10-4-2011 Besam SW200i
Swing doors that are capable of both egress and
ingress shall be marked with a decal, visible from
both sides of the door, with the words CAUTION
Automatic Door, (see Figure 6). The words
Automatic Door must be at least ½ inch in size. It
should be mounted on the door at a height of 585
inches (14713 cm) from the floor to the
centerline of the sign. The sign shall be
minimum of 6 inches (15.2 cm) in diameter and
contain black lettering on a yellow background.
If you need additional decals for your automatic
doors, call your authorized Besam distributor.
3. Guide Rails and Lock Stile – Check that the
guide rails or other barriers or separators are
present (two per swing door side) and firmly
anchored, (see Figures 7, 8, 9).
With the door open, grasp the lock stile of the
door and attempt to move vertically and
horizontally. There should be no looseness in the
door pivots or in the connections between the
door and operator.
4. Housekeeping – Check the door area for tripping
or slipping hazards.
Check all door panels for broken or cracked
glass. Panels should be made of safety type
material. There should be no bulletin boards,
literature racks, merchandise displays, or other
attractions in the door area where people could
be hit by the door.
5. Traffic Patterns – Observe traffic patterns. Plan
routing so people enter and exit in a straight
approach, directly on to the end of the mat.
6. Inspect the finger guard to ensure that it is secure
and in good repair.
NOTE!
Regardless of which activating device is used, if
you have a problem you cannot correct, turn off
the door operating equipment and call your
service representative.
Figure 4

Page 8 Issued: 10-4-2011 Besam SW200i
Swing doors that are capable of both egress and
ingress shall be marked with a decal, visible from
both sides of the door, with the words CAUTION
Automatic Door, (see Figure 6). The words
Automatic Door must be at least ½ inch in size. It
should be mounted on the door at a height of 585
inches (14713 cm) from the floor to the
centerline of the sign. The sign shall be
minimum of 6 inches (15.2 cm) in diameter and
contain black lettering on a yellow background.
If you need additional decals for your automatic
doors, call your authorized Besam distributor.
3. Guide Rails and Lock Stile – Check that the
guide rails or other barriers or separators are
present (two per swing door side) and firmly
anchored, (see Figures 7, 8, 9).
With the door open, grasp the lock stile of the
door and attempt to move vertically and
horizontally. There should be no looseness in the
door pivots or in the connections between the
door and operator.
4. Housekeeping – Check the door area for tripping
or slipping hazards.
Check all door panels for broken or cracked
glass. Panels should be made of safety type
material. There should be no bulletin boards,
literature racks, merchandise displays, or other
attractions in the door area where people could
be hit by the door.
5. Traffic Patterns – Observe traffic patterns. Plan
routing so people enter and exit in a straight
approach, directly on to the end of the mat.
6. Inspect the finger guard to ensure that it is secure
and in good repair.
NOTE!
Regardless of which activating device is used, if
you have a problem you cannot correct, turn off
the door operating equipment and call your
service representative.
Figure 5

Page 8 Issued: 10-4-2011 Besam SW200i
Swing doors that are capable of both egress and
ingress shall be marked with a decal, visible from
both sides of the door, with the words CAUTION
Automatic Door, (see Figure 6). The words
Automatic Door must be at least ½ inch in size. It
should be mounted on the door at a height of 585
inches (14713 cm) from the floor to the
centerline of the sign. The sign shall be
minimum of 6 inches (15.2 cm) in diameter and
contain black lettering on a yellow background.
If you need additional decals for your automatic
doors, call your authorized Besam distributor.
3. Guide Rails and Lock Stile – Check that the
guide rails or other barriers or separators are
present (two per swing door side) and firmly
anchored, (see Figures 7, 8, 9).
With the door open, grasp the lock stile of the
door and attempt to move vertically and
horizontally. There should be no looseness in the
door pivots or in the connections between the
door and operator.
4. Housekeeping – Check the door area for tripping
or slipping hazards.
Check all door panels for broken or cracked
glass. Panels should be made of safety type
material. There should be no bulletin boards,
literature racks, merchandise displays, or other
attractions in the door area where people could
be hit by the door.
5. Traffic Patterns – Observe traffic patterns. Plan
routing so people enter and exit in a straight
approach, directly on to the end of the mat.
6. Inspect the finger guard to ensure that it is secure
and in good repair.
NOTE!
Regardless of which activating device is used, if
you have a problem you cannot correct, turn off
the door operating equipment and call your
service representative.
Figure 6
Guide Rails and Lock Stile –Check that the guide rails or other barriers or sepa-
rators are present (two per swing door side) and firmly anchored, (see Figures
4, 5, 6).
With the door open, grasp the lock stile of the door and attempt to move verti-
cally and horizontally. There should be no looseness in the door pivots or in the
connections between the door and operator.
1
Housekeeping –Check the door area for tripping or slipping hazards.
Check all door panels for broken or cracked glass. Panels should be made of
safety type material. There should be no bulletin boards, literature racks, mer-
chandise displays, or other attractions in the door area where people could be
hit by the door.
2
Traffic Patterns –Observe traffic patterns. Plan routing so people enter and exit
in a straight approach, directly on to the end of the mat.
3
Inspect the finger guard to ensure that it is secure and in good repair.4
Note: Regardless of which activating device is used, if you have a problem you cannot correct, turn off the door operating
equipment and call your service representative.
1007717-en-US-3.0Issue 2018-03-2812

SIGNAGE according to ANSI /BHMA A 156.19 (Low energy)
50± 12"
50± 12"
34-48"
50± 12"
C
L
Apply to both sides of the door.
When using a wall switch,
apply to both sides of the door.
Apply the push decal to the push
side and the pull decal to the pull
side of the door.
Push plate
PRESS
TO OPEN
21-24-005
21-24-005
PUSH TO
OPERATE
21-24-006
PUSH TO
OPERATE
21-24-006
PULL TO
OPERATE
21-24-008
ACTIVATE
SWITCH TO
OPERATE
21-24-007
ACTIVATE
SWITCH TO
OPERATE
21-24-007
A
B
E
PRESS
TO OPEN
C
D
75-20-102
75-20-102
Surface Applied shown
If problem oc-
curs
Action
Check that all required signage is applied and intact. Mandatory indicates that the signage is required
by European directives and equivalent national legislation outside the European Union.
Dual Side “AUTOMATIC DOOR / CAUTION”
A
Operator designed for disabled people:
Recommended, if applicable (applied to both sides of the door).
B
Dual Side “Activate Switch to Operate”
C
Push side “PUSH TO ACTIVATE”
Pull side “PULL TO ACTIVATE”
D
Activation by disabled people: Recommended, if applicable.
E
Contact your ASSA ABLOY service representative. For contact information, see last page.=
13Issue 2018-03-281007717-en-US-3.0

SIGNAGE according to ANSI / BHMA A 156.10
58±5"
Apply to the approach side of the door.
A
B
C
Shall be visible from the side of doors that
swings towards pedestrians attempting to
travel in the wrong direction.
Apply on the swingside of the door.
C
L
75-20-102
DO NOT
ENTER
AUTOMATIC
DOOR
AUTOMATIC
DOOR
75-20-100
75-20-102
DO NOT
ENTER
AUTOMATIC
DOOR
AUTOMATIC
DOOR
75-20-100
Surface Applied shown
If problem oc-
curs
Action
Check that all required signage is applied and intact. Mandatory indicates that the signage is required
by European directives and equivalent national legislation outside the European Union.
Back Side “AUTOMATIC DOOR / DO NOT ENTER”
No entry, identifying one-way traffic: Mandatory, if applicable.
Used in combination with label
C
.
A
Dual Side “AUTOMATIC DOOR / CAUTION”
B
Front Side “AUTOMATIC DOOR” – In
Used in combination with label
A
.
C
Contact your ASSA ABLOY service representative. For contact information, see last page.=
1007717-en-US-3.0Issue 2018-03-2814

General accessories
Your ASSA ABLOY SW200 can be further improved with the following add-ons (please contact your
local ASSA ABLOY company for detailed description).
•Position switch
3
, see page 9
•Electrical lock
9
, see page 9
•Key switch
10
, see page 9
•Elbow switch
10
, see page 9
•Radar
11
, see page 9
•Wireless transmitters (not illustrated)
•Access control (not illustrated)
•Door stop (not illustrated)
Safety accessories
Even though the ASSA ABLOY SW200 is installed to comply with all applicable safety regulations, it
is possible to enhance safety/comfort with the following add-ons (please contact your local ASSA
ABLOY company for detailed description).
•Safety sensors
12
, see page 9
•Finger protection
8
, see page 9
Troubleshooting
RemediesWhat's wrong?
The door does not open
Change the setting of the program selector (see page 6).The motor does not start
Check that there are no objects in the detection zone if a sensor is
fitted.
Check the mains switch and fuse in the building.
Unlock the mechanical locks.The motor starts but door(s)
will not open Check that nothing is jammed beneath the door.
Change the setting of the program selector (see page 6).The door does not close
Check that there are no objects in the detection zone if a safety sensor
is fitted.
Check that nothing is jammed beneath the door.
Check that there are no moving objects within 39"-59" (1-1.5 m)
from the door if an automatic activation unit is fitted.
The door opens and closes
continuously
If the problem continues, please contact your ASSA ABLOY representative.
15Issue 2018-03-281007717-en-US-3.0

Service/Maintenance
Service and adjustments performed by your ASSA ABLOY Entrance Systems-authorized representative
will ensure safe and proper operation of your automatic door unit.
Remember to keep “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
(PRA-0007) available. These are used together.
The table below shows the recommended interval in months, when to replace parts during preventive
maintenance. Talk to your ASSA ABLOY Entrance Systems representative to learn more about our
service offering.
Abusive
Environ-
ment
Cycles/hour in operationPart numberPart
>100<100<10
High
traffic
Medium
traffic
Low
traffic
661224330000271BK/SIPUSH arm service kit
661224330000272BK/SIPULL arm service kit
661224330000276Stop arm kit
661224330000275Micro switch kit
661224330000270BK/SIAdaptor kit
60606060331007291Transmission unit
60606060331007504Connection box kit
60606060331008346Control unit CU-200 with
EXU-boards
Other products from ASSA ABLOY Entrance Systems
•Vertical lifting fabric doors•Door Systems
•Dock levelers•Balance doors
•Dock shelters•Air curtains
•Folding doors•Revolving doors
•High speed doors•Sliding doors
•Loadhouses•Automatic and manual activation units
•Overhead sectional doors
•Service such as preventive maintenance and upgrade programs, emergency repairs, service
advice and door management
1007717-en-US-3.0Issue 2018-03-2816

ASSA ABLOY Entrance Systems is a leading supplier of entrance
automation solutions for efficient flow of goods and people. Building
on the long-term success of the Besam, Albany and Megadoor brands,
we offer our solutions under the ASSA ABLOY brand. Our products and
services are dedicated to satisfying end-user needs for safe, secure,
convenient andsustainable operations. ASSA ABLOY Entrance Systems
is a division within ASSA ABLOY.
assaabloyentrance.us •
assaabloyentrance.ca
ASSA ABLOY Entrance Systems
Tel: [phone]
[e-mail]
assaabloyentrance.us •assaabloyentrance.ca