Assa Abloy CloserPlus Ramp Norton XF460 User manual

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)1
ASSA ABLOY
Installation Instructions Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR
Hinge Edgeof Door
Hinge Edgeof Door
Hinge Edgeof Door
Hinge Edgeof Door
Series Function SizingAdditional Closer Options:- “DA” indicates Delayed Action closing- “R” indicates Ramp Hold-Open function, not handed Optional Accessories:- 7788 Drop Plate- 2019L, 6890, 6891 Soffit Plate Accessories NOTE: For special applications a separate door and frame preparation template is packed with these instructions. In those cases, use this instruction sheet for installation sequence and closer adjustments only.Standard Frame InstallationCloser mounts on opposite to hinge (push) side of door. See Pages 3 and 4Narrow Frame InstallationCloser mounts on opposite to hinge (push) side of door.6890 and 6891 accessories required for this application (supplied separately).See Pages 3 and 4Flush Partition InstallationCloser mounts on opposite to hinge (push) side of door. 2019L accessory required for this application (supplied separately).See Pages 3 and 5CLP7500RCLP770XRHOHO1-62 THRU 6An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.
CAUTION
CAUTION
“X” Designates closer size 2, 3, 4, 5, or 6
Hinge Edgeof Door
Hinge Edgeof Door
ASSA ABLOY
CloserPlus Ramp™ Door Closers (CLP-R)Model Numbers Included:

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)2
ASSA ABLOY
ComponentsScrew PackCloserArmCover OptionsOptionalAccessoriesFor Blade Stop6891 SpacerFor Frameor Blade Stop6890 BracketFor Flush Partition2019L BracketPlastic Cover (Standard)Metal Cover (Optional)2 Cover Screws2019S Block(provided) 2 Cover Screws 9/32" (7 mm) thru;3/8" (9.5 mm) dia. x3/8" (9.5 mm) deep ondoor opposite to closerStandardOptionalThrough-bolts andgrommet-nutsAllPreparation for FastenersDoor or FrameFastenersDrill-SizesSelf-Drilling ScrewWood3/16" (4.80 mm) Pilot hole required1/4" - 20 machine screwMetal Drill: #7 (0.201" dia.)(5mm)Tap: 1/4" - 20 Sleeve nuts and boltsHollowMetal9/32" (7 mm) thru;3/8” (9.5 mm) door faceopposite to closerAluminumor Wood3/8" (9.5 mm) throughAluminumor MetalNo drill requiredNote: Wood doors MUST be pre-drilled when using Self-Drilling Screws.SoffitPlateMain ArmScrewMain ArmSecondary ArmPowerAdjustment Nut
Standard Closer (4 Valves)
DA Option Closer (5 Valves)
TubeCap

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)3
ASSA ABLOY
Installation Instructions
Installation Dimensions Chart
Dim
Up to90°
90°-95°
95°-100°
100°-105°
105°-110°
110°-115°
CLP7500/CLP770X
A in./(mm)
10-1/8(257)
9-1/4(235)
8-5/8(219)
7-7/8(200)
7-3/8(187)
6-3/4(171)
B in./(mm)
10-5/8(270)
9-3/4(248)
9-1/8(232)
8-3/8(213)
7-7/8(200)
7-1/4(184)
C in./(mm)
10-3/4(273)
9-7/8(251)
9-1/4(235)
8-1/2(216)
8(203)
7-3/8(187)
Power Adjustment Chart
DOOR
Dim
*
MAXIMUM DOOR SIZE
32”(0.81m)
36”(0.9 m)
42”(1.1 m)
48”(1.2 m)
INT
CLP7500
0
3
5
8
EXT
4
6
8
12
INT
CLP7700
0
2
5
8
EXT
2
5
8
11
*17 - 360°, MAXIMUM AVAILABLE
Arm Mounting DetailPinion flat will face the door on either right or left hand doors.Arm to Pinion AssemblyFinal InstallationInstall arm roughly here with flat side of pinion to the correct marking on the arm per the illustration below
Y
S
Z
R
L
Y
S
Z
R
L
R
O
T
A
T
E
Select angle of opening and use dimensions shown on Page 4 and Dimension Chart below to locate 4 holes on door for closer body (or 4 holes for 7788 Drop Plate, Page 6, only if required) and 5 holes on stop/rabbet for Soffit Plate (or 4 holes on frame transom for 2019L bracket, only if required). For applications not covered in these instructions, a separate template will be required. Prepare door and frame for fasteners using “Preparation for Fasteners” chart on Page 2. Install closer body to door, or 7788 Drop Plate, with power adjustment shaft away from hinge edge of door and adjustment valves: Down for Left Hand Up for Right Hand Mount 7788 Drop Plate to door ... only if used (see Page 6). Install Main Arm: Close valves (‘S/D’ or ‘S’) and ‘L’, then using a wrench, rotate the pinion shaft at least 50° to permit alignment of the Pinion Flat with the proper arm mark: ‘Z’ for Left Hand ‘Y’ for Right Hand See below right for illustrations of this procedure. Reopen valves (‘S/D’ or ‘S’) and ‘L’, that were closed in previous step. With door closed, align soffit plate with holes in frame and fasten to frame with screws. Use 2019S and/or 6891 spacer blocks or 6890 reinforcing bracket as required. 7500 Series Closers only: Closer is shipped from factory set at mid-range. Using “Power Adjustment” chart below, rotate power adjustment shaft with 1/8” allen wrench supplied: Turn CLOCKWISE to increase power. Turn COUNTER-CLOCKWISE to decrease power. See Page 7 for the illustration of this step. Make adjustments to closer before installing cover. See Page 7 for closer adjustment instructions. CAUTION: Do Not back valves out of closer body or a fluid leak will result. Install cover.
FULL 360 DEGREE TURNSOF POWER ADJUSTMENTSHAFT

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)4
ASSA ABLOY
Standard FrameNarrow FrameNotes:Do Not Scale Drawing.Left Hand Door Shown.Same dimensions apply for Right HandDoor measured from centerline of pivot point.Dimensions are in inches (mm).See Page 3 for A , B, & C dimension values.ACLHinge or Pivot2-1/2(64)2-3/8(60)6-3/4(172)2-3/4(70)3/8(10)2(51)7/16(11)B1/2(13)2-1/16(52)1-3/8(35)2-3/4(70)Standard MountSoffit PlateBlade Stop Mount2019S Block6891 BlockSoffit Plate5/8 Ref.(16)3/8(10)2(51)7/16(11)Hinge orPivotCL1-1/2(38)1(25)B1-1/4(31.8)3/4(19)A2-1/2(64)2-3/8(60)6-3/4(172)NOTE: For Blade Stop Mounting only.Prepare 2 holes for 6890 bracket afterinstalling 6891 block. The 1” dimensionis from the bottom of the 6891 block.Soffit Plate6890 Bracket2 to 2-3/4(51 to 70)6890 Bracket6891 BlockSoffit Plate5/8 Ref.(16)Narrow Frame MountBlade Stop Mount2 to 2-3/4(51 to 70)

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)5
ASSA ABLOY
Flush Partition2-1/2(64)1/2(13)1-1/2(38)1-3/4(44)C3/4(19)ACLHinge or Pivot2-1/2(64)2-3/8(60)6-3/4(172)Soffit Plate2019L AngleBracket

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)6
ASSA ABLOY
Standard FrameFlush PartitionNarrow Frame7788 Drop Plate Mounting Holes7788 Drop Plate7788 Drop Plate7788 Drop Plate2019L Bracket6890 BracketNotes:Left Hand Door Shown.Same dimensions apply for Right HandDoor measured from centerline of pivot point.Dimensions are in inches (mm).See Chart below for D dimension values.CLHinge or Pivot4(102)4-3/4(121)5/16(8)1(25)4(102)4(102)4-3/4(121)5/16(8)1(25)4(102)Hinge orPivotCLCLHinge or Pivot4(102)4-3/4(121)5/16(8)1(25)4(102)DDD
Installation Dimensions Chart
Dim
Up to 90°
90-95°
95-100°
100-105°
105-110°
110-115°
CLP7500RCLP7500XR
Dinch/(mm)
9-7/8 (251)
9 (229)
8-3/8 (213)
7-5/8 (194)
7-1/8 (181)
6-1/2 (165)

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)7
ASSA ABLOY
Control Valve Adjustments(See Figure 3.)Closing Speed Controls (Figure 2A or 2B and 3.) Valve “S” Controls Sweep Range. Valve “L” Controls Latch Range.Unit AdjustmentOpening Cycle “Backcheck” valve controls the strength of cushioning in Backcheck Range. NEVER close this valve completely – it is not to provide a positive stop. (see Figure 4 and Figure 5).Closing Speed ControlsClosing Speed ControlsFigure 2Figure 32B2A
1/8"HexKey
SlowFast"L" (Latch)"L" (Latch)"S/D” (Sweep)"S" (Sweep)"S/D" (Delayed Action)StandardClosing CycleDelayed ActionClosing CycleStandard CloserDelayed ActionCloserAll ValvesDo not force valvescounter-clockwise outof closer body or a fluidleak will occur.Adjust Closing Speed Time to between 3 to 7 seconds from 90°. Use of the door by handicapped, elderly or small children may require greater closing time.Closed
10°
70°
h
c
t
a
L
Closed
10°
h
c
t
a
L
R
a
e
p
e
n
w
g
e
S
D
e
l
a
y
R
a
n
g
e
p
e
e
w
S
Closing Power ControlFigure 1Install closer per instructionswith the proper pre-load applied to the arm then adjust spring power. The power adjustment will notwork properly if the closerspring is not pre-loaded.To increase power, use 11/16"wrench to turn poweradjustment nut clockwise.To decrease power, turn nutcounter clockwise. DO NOT use a power drill or driver to turn adjustment nut. This will damage closer and void warranty.For 7500 Series OnlySet closer to desired size. For recommended sizes, refer to the Power Adjustment Chart on page 3.Opening Door ControlsFigure 4BackcheckFigure 5
1/8"HexKey
IncreaseDecrease
1/8"HexKey
Backcheck CushionBackcheck PositionOpen for backchecklater in door-openingcycle."P"(Normally Closed)"B"(NEVER CloseCompletely)Do not force valvescounter-clockwise outof closer body or a fluidleak will occur.Opening Cycle
a
c
B
k
c
h
e
c
k
g
n
i
n
e
p
O
+
-
The hold-open mechanism is controlled by the hex nut feature located on the secondary arm underneath cap. Remove the cap by pulling straight down. Use a 7/16” wrench to adjust. Turning hex nut feature clockwise will increase the hold-open force. Turning hex nut feature counterclockwise will reduce the hold-open force. Hold-open mechanism can not be disengaged.
Hold-Open Feature
CapHexDECREASE - - INCREASEDO NOT use a power drill or driverto turn adjustment nut. This will damage closer and void warranty.
3000 Highway 74 East • Monroe, NC 28112Tel: (877)- • Fax: [phone]-2255www.nortondoorcontrols.com
ASSA ABLOY

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)8
ASSA ABLOY
Page Left Blank Intinially