Astonica 50101033 User manual

OUTDOORLIVING
Read the instructions and precautions before use of this product
MODEL NO: 50101033
Please keep this instruction manual for future reference
Made in China
© 2002 Distruibuted by:
World Factory, Inc.®
Southlake, TX
1-888-422-7800
Limited Warranty
World Factory, Inc.® Products for Home Use
World Factory, Inc.® (Seller) warrants to the original Buyer only, that each Astonica™ Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase. SELLER’S
SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL
BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN
MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER WHICH HAVE BEEN
MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM REPAIRS OR
ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER MAINTENANCE, NEGLECT
OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This warranty does not apply to
damage, heat-induced coloration changes, scratching or alteration due to normal use or weathering. To
make a claim under this Limited Warranty, you must return the complete product, transportation prepaid, to
any World Factory, Inc.® authorized service center. Call 1-888-422-7800 for the location of the nearest
authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR
FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS,
ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such provision
shall not affect any other provision herein, this Limited Warranty shall be construed as if such invalid and/or
unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all prior
agreements, arrangements, or understandings between the parties relating to product warranty.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-422-7800.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-422-7800.
CAST ALUMINUM LOUNGER
Instruction Manual

2 3
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A
A
1Seat
B 1Backrest
C 2Front Leg
D 2Armrest Assembly
E 2Wheel
F 1Backrest Support Bar
Axle
8mm x 40 Screw
8mm x 35 Stud
8mm x 30 Stud
6mm x 45 Screw
8mm Flat Washer
8mm Lock Washer
8mm Hex Nut
G
H
I
J
K
L
M
N
1
6
6
2
2
6
12
6
ASSEMBLY INSTRUCTIONS
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-422-7800.
Carefully remove the contents from the package.
If any parts are missing do not attempt to use the product until they have
been obtained and correctly installed.
1. Turn the seat (A) upside down on a non-scratching surface. Attach the front
legs (C) to the seat (A) by threading (6) 8mm x 35 studs (I) into the holes under
the front end of the seat (A). Place the legs (C) over the studs (I) and secure
them in place with (6) 8mm flat washers (L), lock washers (M), and hex nuts (N).
2. Insert the axle (G) into both armrest assemblies (D). Then, align the holes in the
sides of the armrest assemblies (D) with those in the sides of the seat (A).
Secure them together with (2) 8mm x 40 screws (H) and lock washers (M) on
each side, screwing them in from the outside.
3. Slide a wheel (E) onto the axle (G). Screw in an 8mm x 30 stud (J), then place a
16mm flat washer (S), 8mm lock washer (M) and hex cap nut (O) on the end to
secure the wheel (E) in place. Repeat this procedure with the other wheel (E).
4. Attach the backrest (B) to the armrest (D) with an 8mm x 45 screw (H) and flat
washer (T) on each side, screwing them in from the outside.
5. Attach the backrest support bar (F) to the backrest (B) using a 6mm x 45 screw
(K), flat washer (P), lock washer (Q) and hex cap nut (R).
6. Adjust the inclination of the backrest (B) by placing the backrest support bar (F)
in the desired notch on the back of the armrest assembly (D).
8mm Hex Cap Nut
6mm Flat Washer
6mm Lock Washer
6mm Hex Cap Nut
16mm Flat Washer
O
P
Q
R
S
2
2
2
2
2
C
D
H
M
E
JSMO
E
D
C
I
LMN
B
F
K
G
PQR
H
M
H
T
8mm Flat Washer
T2