Astonica 50103543 User manual

021112rev1
®
Model No: 50103543
Granite Bay 26.5" Square
Tile Top Cafe Table
Instruction Manual
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
For warranty information, please refer to the back page of
this instruction manual.
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Made in China
©2012 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM
REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized
service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.

ASSEMBLY INSTRUCTIONS
A
A
C
Figure 1
Figure 2
Figure 3
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Tiles 4
B Table Top 1
C Leg Support 1
D Table Legs 4
E Bolts M6x25 8
F Bolts M6x37 8
G Nuts 8
H Washers 16
I Hex Key 1
J Wrench 1
K Bolt Cover 8
L Nut Cover 8
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
Parts Detail
1
NOTE: This product is intended for residential, non-commercial use.
2
B
B
C
B
D
D
E
E
F
F
H
H
H
G
G
I
I
JK
K
K
L
L
J
CAUTION: Do not over tighten fasteners.
1. (FIGURE 1) Place table top (B) upside down
on a flat non-scratch surface. Connect table legs
(D) to table top (B) using bolts (E) and
washers (H). Tighten bolts (E) with hex key (I).
Repeat for three remaining table legs.
2. (FIGURE 2) Place leg support (C) between table
legs (D) and secure with bolts (F), washers (H)
and nuts (G) using wrench (J) and hex key (I).
Do not tighten fully.
3. (FIGURE 3) Turn the table upright. Tighten
bolts (F) and nuts (G) with hex key (I) and
wrench (J). Put the tiles (A) on the table top (B).
D
4. Apply the bolt covers (K) and nut covers (L) to
all exposed bolts and nuts.