Astonica 50104265 User manual

230911rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Made in China
©2011 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
Model No: 50104265
For warranty information, please refer to the back page of
this instruction manual.
Junior Safari Bench
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.

A
E
E
H
I
J
J
Figure 1
C
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
ASSEMBLY INSTRUCTIONS
CAUTION: Do not over tighten fasteners.
2. (SEE FIGURE 2) Attach the wood slats (B)
to leg and arm support (C) as shown.
Repeat on the other side, but do not
tighten bolts until all wood slats (B) are in
place and bench is upright on the floor.
1. (SEE FIGURE 1) Using bolts (E), 2 washers (H
on top, I on bottom) and nuts (J) attach one
end of the straight back (A) to the leg & arm
frame (C) tabs to the inside of the frame.
Attach the other end of the back to the
second leg & arm frame (C).
12
NOTE: This product is intended for residential, non-commercial use.
Figure 3
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Straight Back 1
B Wood Seat Slats 4
C Leg & Arm Frame 2
D Side Seat Brace 2
E 6mm x 32mm Bolt 4
F 6mm x 30mm Bolt 8
G 6mm x 20mm Bolt 2
H 6mm Washer 24
I 8mm Washer 4
J Nut 14
K Wood Screw 6
L Middle Seat Brace 1
EKL
J
F
A
BC
I
DGH
Parts Detail
B
C
H
J
J
H
K
C
G
M
B
D
F
Figure 2
3. (SEE FIGURE 3) Turn the bench over on a
non-scratch surface and attach middle
seat brace (M) to the slats (B) at the midway
point between legs (C) using wood screws (K).
Work from the front to back, bending middle
seat brace (M) as necessary to fit the contour
of the slat seat. Attach side seat brace (D) to
the leg (C) using bolts (G), 2 washers (H) and
nuts (J). Connect side seat brace (D) to the
slats (B) using wood screws (K).
4. Ensure all fasteners are securely tightened.
H
I