Astonica 50100039 User manual

MODEL NO: 50100039
3-Piece Aluminum Bistro Set
Instruction Manual
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Made in China
©2004 World Factory, Inc.®
Distributed by:
World Factory, Inc.®
Southlake, TX 76092
112204rev2
Limited Warranty
World Factory, Inc.®Products for Home Use
World Factory, Inc.®(Seller) warrants to the original Buyer only, that each Astonica®Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.
®authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.

Table Assembly
1. (SEE FIGURE 1) Place table top (A) upside
 down on a flat non-scratch surface.
2. Thread studs (G) into three holes in
 bottom of table top (A) until seated.
3. Attach table legs (B) to table top studs (G),
 using flat washers (I) and hex nuts (J).
 Do not fully tighten fasteners.
4. (SEE FIGURE 2) Position center ring (C) on
 top of mounting tabs in legs (B).
5. Thread screw (M) through center ring (C),
 and mounting tabs in legs (B).
6. Fasten center ring using flat washers (K)
 and hex nuts (L).
7. Turn table upright on a flat level surface
 and tighten all fasteners.
CHAIR ASSEMBLY
1. (SEE FIGURE 3) Thread studs (G) into
 holes in bottom of chair back (D).
2. Thread studs (H) in chairs seats (E)
 until seated. Do not over tighten.
3. Place chair backs (D) on studs in chair
 seats (E) and secure using flat washers (I)
 and hex nuts (J).
4. Fit one chair leg (F) over studs in bottom of
 chair seat (E).
5. Fasten chair leg to seat using flat
 washers (I) and hex nuts (J).
6. Repeat for remaining legs.
ASSEMBLY INSTRUCTIONS
CAUTION: Do not over tighten fasteners.
B
K
L
MM
A
B
B
B
I
I
I
J
J
J
G
GG
C
Figure 1
Figure 2
Figure 3
F
E
D
J
I
G
J
I
H
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A 1Table Top
B3Table Leg
C 1Center Ring
D2
Chair Back
Chair Seat
E2
Chair Leg
F8
Stud, 8mm x 30
G7
Flat Washer, 8mm
I23
Stud, 8mm x 25
H16
Hex Nut, 8mm
J23
Flat Washer, 8mm
K3
Hex Nut, 8mm
L3
Screw, 8mm x 30
M3
ABC
D
EF
I J K L
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
G H M