Astonica 50104296 User manual

®
Model No: 50104296
Natural Wood Rocking Chair
Instruction Manual
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
For warranty information, please refer to the back page of
this instruction manual.
Made in China
©2011 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
141011rev1

PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Chair Back 1
B Front Bracket 1
C Seat 1
D Runners 2
E Right Arm 1
F Left Arm 1
G Lower Support Pole 4
H Upper Support Pole 2
I Screw 50mm 2
J Screw 45mm 6
K Screw 38mm 4
L Hex Key 1
A
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
Parts Detail
1
B
C
D
EF
I
G
H
JK L

ASSEMBLY INSTRUCTIONS
4. (SEE FIGURE 4) Carefully rotate the
assembly to an upright position.
5. Attach seat (C) to the chair assembly (A)
using 38mm screw (K) through the upper
support poles (H) and into the seat (C) from
the bottom.
Figure 4
Figure 5
5. (SEE FIGURE 5) Attach chair arms (E,F) to
chair assembly using 50mm screw (I) and
45mm screw (J).
23
H
K
C
KK
II
F
E
ASSEMBLY INSTRUCTIONS
1. (SEE FIGURE 1) Put chair back (A) on a
flat, non-scratch surface. Attach upper
support poles (H) to the chair back (A).
Insert lower support poles (G) into the
hole on the legs of chair back (A).
Figure 1
2. (SEE FIGURE 2) Attach front bracket (B) to
the support poles (G,H). Figure 2
3. (SEE FIGURE 3) Attach the runners (D) to
the end of front bracket (B) and
chair back (A) using the 45mm screws (J).
Figure 3
A
A
JJ
J
B
H
G
G
B
D
H
G
H
A