Astonica 50105573 User manual

Model No. 50105573
Springhill 48"
Cast Aluminum Table
Instruction Manual
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Made in China
©2005 World Factory, Inc.
Distributed by:
World Factory, Inc.
Coppell TX 75019
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.®Products for Home Use
World Factory, Inc.®(Seller) warrants to the original Buyer only, that each Astonica®Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.®authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
®
270905rev1
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.

PARTS LIST
PART # DESCRIPTION QUANTITY
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
ASSEMBLY INSTRUCTIONS
NOTE: This product is intended for residential, non-commercial use.
AB
GF
DE
H
C
Figure 1
A
E
G
H
F
C
D
G
H
F
B
 CAUTION: Do not over tighten fasteners.
1. (SEE FIGURE 1) Place table top (A) upside down on flat non-scratch surface.
2. Install threaded studs (E) into table top (A).
3. Turn one table leg (B) upside down and align leg over threaded stud (E).
4. Place flat washer (G) and lock washer (H) onto threaded stud. Attach leg using hex nut (F).
 Repeat steps 3 and 4 for remaining table legs. Do not tighten hardware.
5. Install threaded studs (E) into each table leg (B).
6. Align connecting ring (C) between table legs (B) and place connecting ring over threaded studs.
7. Place flat washer (G) and lock washer (H) over each threaded stud, secure using hex nut (F).
 Do not tighten hardware.
8. With each leg attached to the connecting ring tighten each hex nut a few revolutions at a time,
 alternating between hex nuts in a cross corner "X" fashion.
NOTE: Tightening every other hex nut in a cross fashion will ensure your table is level by
 placing equal pressure on each joint.
9. Install adjustable feet (D) at bottom of each table leg (B). Turn table upright.
10.Adjust table legs as needed using the adjustable feet at bottom of each leg. Turn feet by
 hand until table is level to the floor.
 Your table is now ready to use.
12
A Table Top 1
B Table Leg 4
C Connecting Ring 1
D Adjustable Feet 4
E Threaded Stud, 8mm 16
F Hex Nut, 8mm 16
G Flat Washer, 8mm 16
H Lock Washer 16
E