Asus P2-M2A690G - P Series - 0 MB RAM User manual

English
P-Series
ASUS PC (Desktop Barebone)
Installation manual
E4233
Download the latest manual from the ASUS website: www.asus.com
P2 P4

2 Installation manual
English
Front/Rear panel features
1. Optical drive eject button ( )
2. HDD LED ( )
3. Optical drive bay cover
4. Open the front panel cover
5. Power button ( )
6. Power LED ( )
7. Front panel cover
8. Reset button ( )
9.* • MS/MS Pro card slot ( )
• CF card slot ( )
• SD/MMC card slot ( )
• MS/MS Pro/SD/MMC card slot ( )
• 6-pin IEEE 1394a port ( )
• S/PDIF In port ( )
• ESATA/USB port ( )
• USB + ESATA/USB port ( )
• Infrared Receiver ( )
10.* • 4-pin IEEE 1394a port ( )
• USB 2.0 ports ( )
• Headphone port ( )
• Microphone port ( )
11. Power connector
12.** Voltage selector switch
13.* • PS/2 keyboard port ( )
• PS/2 mouse port ( )
• VGA port ( )
• HDMI port ( )
• Parallel port ( )
• USB 2.0 ports ( )
• LAN (RJ-45) port ( )
• Serial (COM1) port ( )
• DVI-D port ( )
• Optical S/PDIF Out port ( )
• Coaxial S/PDIF Out port ( )
 •Audioportscongurations:
• 6-channel
• 8-channel
14. Expansion slot metal brackets
P2 Front (Close) Front (Open)
NOTE: *The front/rear panel slots/ports and their locations may vary, depending on the
model of your system. For detailed descriptions, refer to the system User Guide.
NOTE: **The system’s power supply unit has a 115V / 230V voltage selector switch
located beside the power connector. Use this switch to select the appropriate system
input voltage according to the voltage supply in your area.
RearP4 Front (Close)
6
2
3
4
1
5
7
8
10
9
13
12
11
14
1
2
3
5
4
6

3Installation manual
English
Internal components
1. Front panel cover
2. 5.25-inch optical drive and
3.5-inch hard disk drive cage
3. Power supply unit
4. PCI/PCIE card riser bracket
(connected to the motherboard
PCI/PCIE slot)
5. ASUS motherboard*
6. DIMM sockets
7. CPU socket
1
3
45
2
NOTE: *Refer to the system User Guide for motherboard details.
7
6
Removing the cover
1. Remove the cover screws on the rear panel. Keep the screws for later use.
2. Pull the cover toward the rear panel.
3. Lift the cover, then set it aside.
1. Locate the front panel cover
hooks, then lift them until
they disengage from the
chasis.
2. Swing the front panel cover
to the right, remove it, and
set it aside.
Removing the front panel cover
R
2
1
23
1
Removing the storage drive assembly
1. Lay the system on its side,
then locate and remove
three storage drive assembly
screws.
2. Lift the storage drive
assembly, then set aside.
2
1
1
1

4 Installation manual
English
CAUTION! To prevent damage to the
socket pins, do not remove the PnP cap
unless you are installing a CPU.
Installing an Intel®CPU
1. Locate the CPU socket on the
motherboard.
2. Press the load lever with your thumb
(A), then move it to the left (B) until it
is released from the retention tab.
3. Lift the load lever in the direction of the arrow to a 135º angle.
4. Lifttheloadplatewithyourthumbandforengertoa100ºangle(4A),then
push the PnP cap from the load plate window to remove (4B).
5. Position the CPU over the socket, making sure that the gold triangle is on the
bottom-left corner of the socket. Fit the socket alignment key into the CPU
notch.
6. Close the load plate (6A), then push the load lever (6B) until it snaps into the
retention tab.
Load lever
Retention tab
A
B
Gold
triangle
mark
Alignment key
6B
6A
Load plate
PnP cap
4B 4A
3
Installing an Intel®CPU heatsink and fan
1. Place the heatsink on top of the installed CPU, making sure that the four
fasteners match the holes on the motherboard.
2. Push down two fasteners at a time in a
diagonal sequence to secure the heatsink and
fan assembly in place.
3. When the fan and heatsink assembly is in
place, connect the CPU fan cable to the
connector on the motherboard.
CAUTION. Do not forget to connect the CPU
fan connector! Hardware monitoring error can
occur if you fail to plug this connector.
B
B
A
1
1
A

5Installation manual
English
Removing an AMD CPU fan and heatsink
assembly
1. Remove two screws securing the blower to the
CPU fan.
2. Carefully lift each locking lever and detach its end
from the hole of the retention module.
3. Release the hook of each metal clip from the hole
of the retention module.
4. Remove the metal clips from the side rail of the
fan and heatsink assembly.
5. Disconnect the CPU fan cable from the connector
on the motherboard, then remove the fan and heatsink assembly.
Retention module
Locking
levers
2
1
5
Installing an AMD CPU
1. Locate the CPU socket, then lift the socket lever to a 90º angle.
2. Install the CPU to the socket, making sure that the CPU corner with the gold
triangle matches the socket corner with a small triangle.
3. Push down the socket lever to secure the CPU.
1 2 3
NOTE: To reinstall AMD CPU fan and heatsink assembly, follow the instructions in
reverse order.
CAUTION: After you reinstall a fan and heatsink assembly, do not forget to connect
the CPU fan connector! Hardware monitoring error can occur if you fail to plug this
connector.
3
4
Hook
Metal clip
4

6 Installation manual
English
Installing an expansion card
1. Lift the PCI/PCIE riser card
assembly to remove.
4. Reinstall the PCI/PCIE riser card
assembly. Make sure that the riser
card connector sits properly on the
motherboard PCI/PCIE slot.
Installing a DIMM
1. Locate the DIMM sockets in the motherboard.
2. Unlock a DIMM socket by pressing the retaining clips outward.
3. Align a DIMM on the socket such that the notch on the DIMM matches the
break on the socket.
4. Push the DIMM to the socket until the retaining clips snap inward.
CAUTION:
• Unplug the power supply before adding or removing DIMMs. Failure to do so may
cause damage to the motherboard and/or components.
 • ADDRDIMMiskeyedwithanotchsothatittsinonlyonedirection.Donotforce
a DIMM into a socket to avoid damaging the DIMM.
2. Remove the metal cover opposite
the slot that you intend to use.
3. Insert the card connector to the
slot,thenpressthecardrmly
untilittsinplace.Securethe
card with a screw.
3
2
4

7Installation manual
English
Installing optical and storage drives
1. Turn the storage drive assembly upside down with the 3.5-inch bay on top of
the 5.25-inch bay.
2. Insert the optical drive upside down to the 5.25-inch bay, then secure it with
two screws on both sides.
3. Turn the storage drive assembly, insert the hard disk drive upside down to the
3.5-inch bay, then secure it with two screws on both sides.
Reinstalling the storage drive assembly
1. Connect the SATA/IDE (1A) and power (1B) plugs to connectors at the back
of the optical drive.
2. Connect the SATA/IDE (2A) and power (2B) plugs to the connectors at the
back of the SATA/IDE hard disk drives.
3. Install the storage drive assembly to the chassis.
4. Secure the storage drive assembly with three screws.
1A
1B
SATA IDE
2A
2B 2A
2B
23
R
3
R
4
1B
1A
SATA
IDE

8 Installation manual
English
NOTE: For P2 model, if your optical
drive tray fails to eject when you press
the eject button, attach the provided
stickers (0.5mm and 1.0mm) to the
location shown at the back of the front
panel cover. Make sure the sticker aligns
with the optical drive eject button.
1. Insert the foot stand hooks into
the holes on the chassis.
Installing the foot stand
2. Pull the foot stand to the direction
of the arrow until the lock snaps
in place.
NOTE: To remove the foot stand, lift the lock, then slightly push the foot stand to the
direction of the rear panel until it disengages from the chassis.
Reinstalling the cover
1. Insertthecovertothechasis.Makesurethecovertabstthechasisrails.
2. Pushthecovertowardthefrontpaneluntilittsinplace.
3. Secure the cover with two screws you removed earlier.
Reinstalling the front panel cover
NOTE: Refer to the pictures in the section “Removing the cover” on page 3 in reverse
order.
R
2
1. Insert the front panel
cover tabs to the holes
on the right side of the
chassis, then swing
the front panel cover to
the left.
2. Insert the front panelInsert the front panel
cover hooks to the
chassis until the front
panelcovertsin
place.
Sticker
1