AT&T Business in a Box BIB NextGen User manual

AT&T Business in a Box®
BIB NextGen
Quick Start Guide
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.
Please ensure that you have set-up the equipment before the date scheduled
with your AT&T Order Manager for Test and Turn Up of your service

The following components are included in your router package:
What’s in the Box
2
AT&T Business in a Box® NextGen
Base Unit Router
RJ11 modem cable
Labelled ISE644 (Qty 1)
Router power cable
Note: Your solution may
require other specific cables
including WAN or telephony
cables and will be provided in
the box.
Site Documentation
Package
6 outlet power strip
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.
Analog Breakout Box with Amphenol
Cable

Understanding your AT&T Business in a Box® Equipment
AT&T Business in a Box® NextGen Base Unit Router
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.
Ethernet LAN Ports
1GigE ports
Ethernet WAN Ports
Electrical and Optical
T1 Ports (4)
Grey Cables from Smartjack to port.
Red cables for PRI
Survivability Ports (2)
RJ11
Analog voice port (22)
Customer Provided Cable to
Amphenol connector or to Breakout
Box.

The AT&T Business in a Box® router may be wall mounted on a
¾” or thicker plywood backing. The unit is too heavy to be
mounted to drywall. Use the rack-mount brackets, bracket
screws (included) and 1½” wood screws (not included).
Complete the following steps:
1) Position the device so that the front panel is facing down
and apply the rack-mount brackets with bracket screws to
each side as shown in Figure 1. Rack-mount bracket
position.
2) Attach the bracket to ¾” or thicker plywood backing using
four (4) 1 ½” wood screws as shown in Figure 2. Rack-
Mount bracket on plywood backing.
3) Optionally, attach the black Breakout Box with included rack
mount hardware.
Important: Cables will flow down and should be dressed using a
wire minder. The unit should be mounted high enough that the
technician can see the status lights**. See Figure 3 Installation
example.
Step 1 –Wall Mounting Instructions (optional to Rack Mounting)
4
** It is recommended, but not required that a skilled technician mount the router on the wall.
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.

Step 2 - Attach Power Cord to Router and Proper Grounding
5
Plug in power cord to router and attach customer
provided ground cable
To included
power strip
On/Off Power
Switch - Leave
powered off until
ready for service
activation
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.
Grounding Lug –
(Customer Provided
ground cable) Connect
#10 stranded ground to
closest earth ground or
building bus bar.

Step 3 - Connect Analog POTS line to Internal Modem
Connect customer provided Analog POTS line from wall jack to the
internal modem using the provided brown RJ11 cable.
6
To wall jack
RJ11 modem cable
Labelled ISE644
Note: The POTS line may be used in the turn-up of your service as well as by AT&T’s Global
Customer Service Center.
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.

Step 4 - Connect Router to Ethernet Circuit
Connect your Ethernet circuit using the Grey Ethernet cable to the
Ethernet WAN port pictured below.
7
RJ45 Cable labelled ISE1015-025
To Ethernet
Circuit
termination
device
Note: The Ethernet WAN port on the router example is for electrical Handoff. Should
your solution require optical handoff you will connect the fiber cable to the included SFP
module and insert into the SFP slot depicted to the right of the example above.
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.

Step 5 - Connect Router to your Ethernet LAN Devices
Connect your Ethernet LAN devices (External Firewall, External Customer
Switch, PC’s, printers, servers, etc.) to the integrated Ethernet switch or
per instructions in your Site Documentation Package.
8
Customer provide
RJ45 LAN Cable(s)
Note: If utilizing your own Ethernet switch/firewall behind the AT&T Business in a Box®
router then utilize only Port 2 to interconnect.
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.

AT&T Business in a Box® User Guide
AT&T Business in a Box® includes integrated IPSec VPN and Point to Point
Tunneling Protocol for remote access capabilities available with your
service. A User Guide is available to assist customers with logging into the
device using a web browser and configuring to your needs.
9
© 2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.