ATC Toledo FPH1000T Instruction manual

FPH1000T
FPH1500T
FPH2000T
Toledo Panel Heater
INSTALLATION,OPERATION &
MAINTENANCE MANUAL
Class I - IP 20
This Product is only suitable for well
insulated spaces or occasional use

1. IMPORTANT SAFETY INSTRUCTIONS
These instructions should be read carefully before installation and retained by
the user. The booklet must be kept and delivered to the new user in case of
change of ownership of the heater. The Manufacturer reserves the right to
vary the features of the product without prior notice. The technical data are
indicative only.
1. This heater is intended solely for the use it has been designed for, namely
space heating. The Manufacturer or Distributor is not responsible for any
damage that could happen due to improper use.
2. After unpacking, make sure that the heater is complete and shows no
signs of tampering or any visible damage. Should the unit be damaged please
return to the place of purchase.
3. Packing materials are potentially dangerous, keep away from children.
4. The heater can be used by children of at least 8 years of age (as well as by
persons with reduced physical, sensory or mental capabilities, or lack of
experience or required knowledge) provided that they are under supervision,
or after they have been instructed relating to the safe use and have
understood the potential dangers. Children should not play with the Heater.
5. Cleaning and maintenance must be performed by the user and not by
unsupervised children.
6. Children aged between 3 and 8 years of age shall not plugin, regulate, clean
the heater or perform maintenance. Children of less than 3 years should be
kept away unless continuously supervised.
7. Children aged from 3 years and less than 8 years shall only switch on/off the
heater provided that it has been placed in its intended normal operating
position and they have been given instruction concerning use of the heater
in a safe way and understand the hazards involved. Children should always be
supervised.
8. Before connecting the heater make sure that the voltage is the same as
indicated on the device rating label.
9. Do not use in presence of gas, inflammable or explosive liquids or substances
as defined in BS5345.
10. Some fundamental rules which apply to all electrical devices must be observed
when using the heater:
• Do not touch the heater with wet hands.
• Do not handle the heater when you have bare feet.
• Do not let children play with the heater.

11. Avoid the use of extension cords with this product, extension cords may
overheat and there could be a risk of fire.
12. Do not make any modification to the Heater.
13. Keep connections dry.
14. If the power supply cord is damaged, do not use the heater until the cord has
been replaced. For power cord replacement, always contact an electrician in
order to avoid any risk of injury.
15. If the heater is not going to be used for a long period, disconnect it from the
power supply.
16. Always disconnect the heater before doing any maintenance
CAUTION - Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and vulnerable
people are present.
2. ELECTRICAL INSTALLATION NOTES
The installation should always be carried out by a qualified electrician or
a competent person in accordance with the current electrical standards:
HD 384 CENELEC for Mainland Europe, IEC 60446 and BS 7671 for the
United Kingdom, IEC 60445(2010) & ET101:2008 for Ireland and IEC 60364-7-708 1988
Internationally. The energy supply to the heater must always be properly earthed. The
heater must be connected to the energy supply using the provided cable.
An overvoltage category III Combined Circuit breaker and Residual
Current Device (RCD) with rated earth leakage operation not exceeding
30mA must be fitted upstream on the supply line. The circuit breaker
must have a contact opening distance of at least 3 mm.
•The heaters should always be used with the mounting feet provided
•Under no circumstances turn the heater on if it is not mounted using the Feet
supplied or if the face of the heater is on any surface.
•The heater must not be recessed in the ceiling. There must be enough space
around the top of the heater to ensure adequate ventilation.
•A minimum air gap of at least 90 cm should always be allowed between the top
of the heater and a ceiling or roof.
•A distance of at least 100 cm should always be left in front of the heaters to
ensure safety
•The Heater must not be located either directly below, or in front of a socket-
outlet.
•The heater must not be used in a bathroom.

•Make sure that there is no possibility of inflammable material, combustible
material or curtains coming into contact with the heater. There is a risk of fire
if this happens.
•DO NOT COVER THE HEATER
3. INSTALLING THE FEET/CASTORS
Remove the heater from the box and place the upper packaging on the ground.
Turn the heater upside down and place the top of the heater into the packaging to
prevent any scratching of the upper surfaces.
With the openings at the bottom of the heater pointing upwards and the outlet
grille facing towards you, insert the feet with the wheels pointing in an upward
direction and the hooks on the feet pointing towards the front of the panel heater.

Once the hooks are through the square openings in the base of the heater, push
the foot towards the front of the panel heater until it is unable to move any
further forward.
Install the locking key into the square opening in the base of the foot and fix it into
place with the screw provided.
Repeat this procedure for the other foot and then return the heater to the upright
position.
Please note the heater will not operate if it is not in the upright position.
4. USE – DO NOT COVER THE HEATER
To turn the heater on
move the red operation
switch on the timer to
either the On position or
Timer position.
When the switch is in the
On position the heater will
operate continuously
under the control of the
thermostat knob once a
heat output is selected.
To select a heat output,
turn on either of the red
neon switches on the right side of the heater. Turning on one switch will operate half
heat, both switches on together will give full output. This selection and also the
thermostat work in both “on” and “timer” modes.
The Timer mode is selected by moving the red operation switch to the timer position.
The timer is a 24-hour programmable unit with 15-minute interval settings. To set the
time, rotate the outer ring in a clockwise direction until the time of day is correct and
the time indicator is in the correct place. Do not turn the outer ring anti-clockwise.

To set the heater to come on push the corresponding program segment to the outer
position of the dial, each segment represents 15 minutes. The timer will keep the same
program every day.
5. MAINTENANCE
ATC Panel heaters contain no user serviceable parts and therefore require very little
maintenance.
Ensure that there is no excessive build-up of dust/dirt on the heater element as this
can cause overheating and premature element failure. To clean the outside of the
appliance, wipe off dirt with a damp cloth.
7. TECHNICAL FEATURES
Product Code
FPH1000T
FPH1500T
FPH2000T
Power (W)
500W/1000W
750W/1500W
1000W/2000W
Voltage (V)
220-240V
220-240V
220-240V
Frequency (Hz)
50-60Hz
50-60Hz
50-60Hz
Element
Finned Aluminium
Finned Aluminium
Finned Aluminium
Thermostat
Adjustable
Adjustable
Adjustable
Safety Cut-out
75˚C
85˚C
90˚C
Size LxDxH mm
576 x 106 x 440
732 x 106 x 440
940 x 106 x 440
Weight
5.17 KG
6.35 KG
8.15 KG
IP Protection
IP20
IP20
IP20
Colour
White
White
White
Approvals
CE, Intertek GS,
RoHs, Lot 20
CE, Intertek GS,
RoHs, Lot 20
CE, Intertek GS,
RoHs, Lot 20

8 ECO DESIGN TABLE
Models
FPH1000T
FPH1500T
FPH2000T
Heat output
Nominal heat output (P
nom
)
1.0 kW
1.5 kW
2.0kW
Minimum heat output (P
min
)
(indicative)
0.5 Kw
0.75 kW
1.0 kW
Maximum continuous heat output
(Pmax,c)
1.0 kW
1.5 kW
2.0kW
Auxiliary electricity consumption
At nominal heat output (el
max
)
N/A
At minimum heat output (el
min
)
N/A
In standby mode (el
SB)
0.05 kW
Type of heat output/room temperature
control:
Mechanic Thermostat Room
Temperature Control
Other control options:
N/A
ATC Electrical and Mechanical
ATC House,
Broomhill Drive,
Tallaght,
D24 EF99,
Ireland.
Tel: [phone],UK Tel: [phone]
Fax: [phone], Email: [e-mail]

9. ENVIRONMENTALLY COMPATIBLE DISPOSAL OF THE APPLI ANCE
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European
countries with separate collection systems).
This marking shown on the product or its literature,
indicates that it should not be disposed of with other
household wastes at the end of its working life.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate
this from other types of waste and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where
they purchased this product, or their local government office, for details of where and
how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial waste for
disposal.
10. GUARANTEE
Your appliance is guaranteed for 3 years– during this period we will repair or exchange,
at our discretion, any faulty or defective parts providing the appliance has been used in
accordance with the operating & installation instructions and has not been misused or
mistreated in any way.
Any unauthorised repair or attempted repair will invalidate the guarantee. You may be
asked to return the product to our workshop for inspection to establish whether the
fault is covered under the guarantee. The guarantee is valid in the UK and Ireland only.
This guarantee is additional to your statutory rights. In the unlikely event of a problem
with your appliance please contact your supplier.
Head Office & Energy Showrooms:
ATC House, Broomhill Drive,
Tallaght, Dublin 24,
Ireland. Tel: [phone]
UK. Tel: [phone]
Email: sal[email protected] www.atc.ie