ATC ATC-810 User manual

1 USB-HS Serial Converter User s Manual v1.1
User sManual
USB-High Speed Serial Converter
Model ATC-810
Overview
Congratulations on your purchase of the ATC s USB-high Speed Serial Converter.
This device provides a simple and easy way to connect Universal Serial Bus (USB)
and Serial port interface.
With the advantage of USB port, users have the capability to utilize the peripheral
with serail port interface in an easy to use environment such as plug and play & hot
swap function. This adapter is designed for ideal connections to Cellular Phone,
Digital Camera, Modems or ISDN terminal adapter with over 1Mbps data transfer
rate.
The USB-high Speed Serial Converter and software drivers are capable of
providing ano-firmware-change feature that enable USB interface to be transparent
to serial port peripherals with minimum modifications.
Package Content
• Hardware: USB-High Speed Serial Converter
• Software: USB-High Speed Serial Converter driver on CD-ROM
• User s Manual
Product Features
• USB Specification Rev. 1.1 compliant

2 USB-HS Serial Converter User s Manual V1.1
• Support the RS232 Serial interface
• Over 1Mbps data transfer rate
• Support remote wake-up and power management
System Requirements
• IBMPC 486DX4-100 MHz CPU or higher or compatible system
• Available USB port
• CD-ROMdrive
• Windows 98 . Windows 2000 .Windows XP.or iMAG
Driver Installation
Followthe steps belowto install driver of USB-High Speed Serial Converter:
1. Power on your computer and make sure that the USB port is enabled and
working properly.
2. Plug in the USB-High Speed Serial Converter into the USB port and run the
Add NewHardware Wizard to assist you in setting up the newdevice. Click
Next to continue.
3. Insert the USB-HS Serial Converter software driver into the CD-ROMdrive
and click Next to continue. For Windows 98, click Search for the best driver
for your device and click to search driver from the floppy drive
D:\DRIVER\Win98&Win2000.
4. Windows will detect the driver (FTDIBUS.INF) and shows the

5USB-HS Serial Converter User s Manual V1.1
USB HS SERIAL CONVERTER. Click Next to continue installation.
5. Click Nextto continue and let Windowscopy the needed files to your hard disk.
6. When Windows finished installing the software required for the new USB to
Serial Cable, click Finish.

4 USB-HS Serial Converter User s Manual V1.1
Setting Upthe RS232 Serial Device
Followthe steps belowto connect your RS232 Serial Device (ie: Modem) to the
USB port of your PC:
1. Turn off your Modem. Plug the DB 9 (or DB 25) connector of the USB-HS
Serial Converter into your Modem. Connect the other end of the USB-HS
Serial Converter to an USB type A to type B cable. Turn on the Modem
afterwards.
2. Turn on your computer and plug in the USB connector of the USB-HS Serial
Converter into the USB port.
3. If you have already installed a Modem device before, click Start, Settings,
Modems. Open Modems Properties, select the Modem, click Properties. In
General tab, please change the Port value to USB Serial Port (COM3).
4. After finishing these processes, you can use USB to Serial Bridge Cable to
connect RS232 Serial 56K FAXModem and execute the Dial-up fuction to
connect Internet, and send the FAXwith the FAXsoftware(ie: Microsoft FAX)
properly.
Uninstalling the Driver Program

5USB-HS Serial Converter User s Manual V1.1
If you want to remove the USB-HS Serial Converterr driver program, you can
uninstall it by following the steps below:
1. Unplug the USB-HS Serial Converter from your PC.
2. Run the D:\Driver\Win98&win2000\FTDIUNIN.EXE program from the
software CD-ROM, Clik finish then reboot the PC.
Disclaimer
Information in this document is subject to change without notice. The manufacturer does not
make any representations or warranties (implied or otherwise) regarding the accuracy and
completeness of this document and shall in no event be liable for any loss of profit or any
other commercial damage, including but not limited to special, incidental, consequential, or
other damages.
No part of this document may be reproduced or transmitted in any formby any means,
electronic or mechanical, including photocopying, recording or information recording and
retrieval systems without the express written permission of the manufacturer.
All brand names and product names used in this document are trademarks, or registered
trademarks of their respective holders.
FCC Statement
This device generates and uses radio frequency and may cause interference to radio and
television reception if not installed and used properly. This has been tested and found to
comply with the limits of a Class B computing device in accordance with the specifications in
Part 15 of FCC Rules. These specifications are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by plugging the device
in and out, the user can to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.

6 USB-HS Serial Converter User s Manual V1.1
• Increase the separation between the device and receiver.
• Connect the computer into an outlet on a circuit different fromthat to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warranty
We warrantythe equipment to be free fromdefects in material and
workmanship, under normaland proper use andinits unmodified condition,
for 3 year , starting on the date it is delivered for use. Out ofwarranty
equipment maybe returned to us . Return shipping charges will be billed to
the customer. The repaired unit will have a 90 daywarranty.
SHEN ZHEN ATC TECHNOLOGY CO., LTD
Room 1102, Block B, Building 109, Tairan T:[phone](3 line)
Industrial & Trading Zone, Futian District F:[phone]
Shenzhen China E-mail: [email protected]m
Website:www.szatc.com

5USB-HS Serial Converter User s Manual V1.1