Atek ARK S 58 User manual

KK-ARK.002 18.04.22 Rev No:2
1
ARK S 58
IP67 INCREMENTAL ROTARY ENCODER
USER MANUAL
ARK S 58 series rotary encoders measure with magnetic principle and work contactless. They give
incremental digital pulse signal output.
They have different resolution values between 1 pulse and 1024 pulses. With their high IP67
protection class, they can work in harsh environmental conditions.
Optionally, different cable length, socket model and shaft diameter can be requested.
GENERAL INFORMATIONS
•The installation of the product is carried out by the customer who purchases the product, according to the wiring diagrams,
installation information, etc. in this manual.
•Maintenance and repair should be done by the technicians authorized by the manufacturer firm.
•There must be minimum distance between the sensor and control unit. Avoid additions except the suitable connector unless
it needs.
•Keep away the sensor cable from as high power energy cables, contactor, motor, switched power supplies, inductive and
capacitive noisy supplies.
•Shielding edge of the sensor cable must be ground connected.
•Not to damage the sensor supply directions and voltage must be paid attention (For TTL sensor max. 5V; PP, HTL, HPL sensor
max. 30V). Don’t energize before all connections completed.
•Transport and storage should be at their original packaging and an ambient temperature of -40°C / +85°C in such a way that
they will not be exposed to dust, humudity, impact, vibration, falling or water.
•Chemicals such as alcohol, thinner etc. should not be used for cleaning the product. The product should be wiped with a
damp cloth.
•The product may be damaged and may become unusable if used outside of the specifications in the user manual.
•The product will be out of warranty if used outside of the specifications in the user manual and opened or repaired other
than authorized services.
WARNINGS
M16 / 8 PIN MALE
SOCKET PIN NO
SIGNAL
CABLE COLOR
1
A
YELLOW
2
/B
WHITE
3
+V
RED
4
0 V
BLACK
5
/A
BLUE
6
B
GREEN
7
/Z
GREY
8
Z
PINK
ELECTRICAL CONNECTIONS
In the left tablet he cable colors of sensors output signals are given. If the control circuit is suitable in the Line Driver
sensors of the not output signals (/A, /B, /Z) have to be added to the system. If it is not suitable /A, /B, /Z signal cables
must be fixed as insulated separately. Don’t forget that these edges have electricity too.
A
/A
B
/B
Z
/Z
90°Phase

KK-ARK.002 18.04.22 Rev No:2
2
*D= 6 mm, 8 mm or 10 mm are available.
Cable From Backside
MECHANICAL DIMENSIONS
Connector From Backside
Cable From Side
Connector From Side
*D= 6 mm, 8 mm or 10 mm are available.

KK-ARK.002 18.04.22 Rev No:2
3
TECHNICAL SPECIFICATIONS
Product
Description
ARK S 58
IP67 Rotary Encoder
User Manual
1 pcs.
Supply and Output
PP : 10…30 VDC Supply
: 10…30VDC Output
TTL : 5 VDC Supply
: 5 VDC TTL RS422 Line Driver Out.
HTL : 10…30 VDC Supply
: 5 VDC TTL RS422 Line Driver Out.
HPL : 5…30 VDC Supply
: 5…30 VDC Push-Pull Output
OCL : NPN Open Collector
OCP : PNP Open Collector
Output Signals
2(A,B)
3(A,B,Z)
4(A,/A,B,/B)
6 (A,/A,B,/B,Z,/Z)
Measuring Type
Magnetic
Max. Operating Speed
3000 RPM
Resolution
All resolution values between 1 and 1024 pulses are available
*Supply Voltage
5VDC, 10…30 VDC
Current Consumption
50 mA nominal
*Output Type
Push pull, TTL Line Driver, Open Collector
*Output Signals
A, /A, B, /B, Z, /Z
Operating Temperature
-25...+85 °C
Storage Temperature
-40...+85 °C
Electrical Connection
M16 socket
5 x 0,14mm2 shielded cable (outer dimater: 5 ±0,2 mm) (When output signal is selected as 2 or 3)
8 x 0,14mm2 shielded cable (outer dimater: 6,5 ±0,2 mm) (When output signal is selected as 4 or 6)
Shaft Diameters
6 mm, 8 mm or 10 mm
IP Protection Class
IP67
Weight
~330 gr
Material
Body: Aluminium
Shaft: stainless Steel
Note: The technical specifications indicated by (*) vary according to the selected model. The detailed code table is shown below.
Resolution
All resolution values
between 1 and 1024
pulses are available
Connector or Cable
Direction
A: From backside
Y: From side
Body Diameter
58 : 58 mm
ARK X XXX XXXX XXX XXX XX XX
Shaft Diamater
6 : 6 mm
8 : 8 mm
10 : 10 mm
PRODUCT CODE TABLE
Model
ARK
Electrical Connection
3M : 3 m
5M : 5 m
10M : 10 m
S13 : M16/8 pin Socket
BOX CONTENTS
Shaft Type
S : Shafted

KK-ARK.002 18.04.22 Rev No:2
4
Manufacturer Firm’s Title, Address Details
Manufacturer Firm: ATEK ELEKTRONİK SENSÖR TEKNOLOJİLERİ SANAYİ VE TİCARET A.Ş.
Address: Gebze OSB, 800. Sokak, No:814, Gebze/KOCAELİ/TURKEY
TEL: [phone] FAX: [phone]
Web: www.ateksensor.com E-mail: [e-mail]
Authorized Service’s Title, Address Details
Authorized Service: ATEK ELEKTRONİK SENSÖR TEKNOLOJİLERİ SANAYİ VE TİCARET A.Ş.
Address: Gebze OSB, 800. Sokak, No:814, Gebze/KOCAELİ/TURKEY
TEL: [phone] FAX: [phone]
E-mail: [e-mail]
Disposal of Packagings: Packaging materials consist of recyclable materials. For providing recycling, please
dispose waste packagings to collecting points of authorized recycling facilities.
Disposal of E-Waste: This device is in conformity with WEEE Directive and consists of recyclable materials. This
product should not be disposed with general waste for preventing negative effects on enviroment and human
health. This product should be disposed to collecting points of authorized recycling facilities. Further
information can be reached from authorized unit.