Overview
The VS-132/VS-134/VS-138 Video Separators (Splitters) are
boosting devices to duplicate the video signal from one
source to 2 (VS-132), 4 (VS-134), or 8 (VS-138) outputs, and
are ideal for any monitor using analog signals. The VS-132,
VS-134, and VS-138 also extend the transmission distance
up to 65m (210 ft.), making them excellent for public
broadcast systems. To send multiple, high quality, XGA
VGA, SVGA or Multisync video signals over long distances
without hassle, the VS-132/VS-134/VS-138 provide your
best choice.
Other useful applications for the Video Splitter include:
• Financial: the remote display of stock market information
• Education: the remote display of lectures and lessons to
lecture halls and classrooms
• Business: the remote display of addresses to overflow
rooms; video conferencing; and demos
Features
• Duplicates Video Signals to Two (VS-132), Four (VS-134),
or Eight (VS-138) Outputs
• Long Distance Transmission - Up to 65 m (210')
• Daisy Chainable
• Supports 350 (VS-132/VS-134) and 300 (VS-138) MHz
Bandwidths
• Supports XGA, VGA, SVGA, and Multisync Monitors
• High Resolution Video - Up To 1600 x 1280
• Supports one XGA Port (Video Out 1)
• DDC Compatible*
* If you connect a DDC type monitor to Video Out 1, all
other monitors must be able to support the highest video
resolution that the DDC monitor can provide.
Hardware Requirements
• One or more XGA, SVGA, VGA, and/or Multisync
compatible analog monitor(s) with standard PC high
density cables having 15 pin D type male connectors.
• One XGA, SVGA, VGA, and/or Multisync analog video
card having a standard PC 15 pin D type female
connector.
Note: 1. This product is not suitable for CGA, EGA, or
Monochrome type monitors using a digital
video signal.
2. UL-2919 rated cable is recommended for the
best video quality.
Introduction
The VS-132
The VS-134
The VS-138
123
This package contains:
•1 Video Splitter (VS-132; VS-134; or VS-138)
•1 AC 9V Power Adapter
•1 User Manual
Check to see if the product has been damaged in shipping. If you
encounter a problem, contact your dealer right away.
Please read this manual thoroughly and follow the installation and
operation procedures carefully to prevent any damage to the unit and/or
any devices it connects to.
All brand names and trademarks are the registered property of their respective owners.
USER'S MANUAL
©Copyright 1999 ATEN® International Co., Ltd.
Manual Part NO. PAPE -1153-200
Printed in Taiwan 07/1999
TO PC VIDEO OUT TO MONITOR VIDEO IN
POWER LED POWER SWITCH
TO PC VIDEO OUT TO MONITOR VIDEO IN
POWER LED POWER SWITCH
Cascading
To cascade Video Splitters, simply use a VGA extension
cable to connect one of the Video Out ports of the parent
unit to the Video In port of the child unit.
Installation
Connecting Up
Setting up the Video Splitter is simply a matter of plugging
in the cables. Refer to the diagrams as you follow the step
by step directions below:
1. Make sure that the computer and monitors you are using
for the installation are all powered Off.
2. Plug the female end of a male to female VGA extension
cable into the Video Splitter's Video In port; plug the
male end of the cable into the computer's video output
port.
Note: The VGA extension cable does not come with the
package, and must be purchased separately (part
no. 2L-2401).
3. Plug the monitor cables into any of the Video Splitter's
Video Out ports that is available.
4. Set the Gain Control
The Gain Control switch for the VS-132 is located just
below the Video In port; the Gain Control switch for the
VS-134 and VS-138 is located on the bottom panel of the
unit. Slide the switch to the High position (toward the
front of the unit on the VS-134 and VS-138), if the
monitors are located greater than 30m away. Slide the
switch to the Normal position (toward the rear of the unit
on the VS-134 and VS-138), if the monitors are located
less than 30m away.
5. Plug the power adapter (supplied with this package) into
an AC source; plug the adapter's power cable into the
Video Splitter's AC 9V Power Jack.
6. Power On all equipment.
Appendix
Specifications Radio & TV Interference Statement
WARNING!!! This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
interference to radio communications. This equipment has
been tested and found to comply with the limits for a Class
A computing device pursuant to Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection
against such interference when operated in a commercial
environment. Operation of this equipment in a residential
area is likely to cause interference, in which case the user
at his own expense will be required to take whatever
measures may be required to correct the interference.
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY
EXCEED THE PRICE PAID FOR THE PRODUCT FROM
THE DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THE PRODUCT, DISK OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation,
expressed, implied, or statutory with respect to the contents
or use of this documentation, and specially disclaims its
quality, performance, merchantability, or fitness for any
particular purpose.
The direct vendor also reserves the right to revise or update
the device or documentation without obligation to notify
any individual or entity of such revisions, or update. For
further inquires please contact your direct vendor.
54 67
Function VS-132 VS-134 VS-138
ConnectorsInput (Male) 15 pin HDB
Output (Female) 2 x 15 pin HDB 4 x 15 pin HDB 8 x 15 pin HDB
LEDs 1 Power Indicator
Function Switches 1 Slide Switch - Video Signal Gain Control
VGA Bandwidth (-3db) 350 MHz 300 MHz
VGA Res/VerticalFreq 1920 x 1440 @ 80 Hz 1800 x 1400 @ 80 Hz
Signal Type XGA, VGA, SVGA, Multisync
Cable Distance 65m [210'] (max.)
Power Consumption AC 9V 120mA (max.) AC 9V 200mA (max.) AC 9V 420mA (max.)
Housing Metal Plastic/Metal
Weight 190g 1150g 1200g
Dimensions (L x W x H) 104 x 98 x 24 mm 224 x 152 x 52 mm
VGA
