ATEN VM7814 User manual

VM7814 / VM8814
4-Port 4K HDMI Input Board / Output Board Quick Start Guide
Hardware Review
VM7814 Front View
1. HDMI Input Ports
2. Audio Input Ports
3. Status LED
VM8814 Front View
1. HDMI Output Ports
2. Audio Output Ports
3. Status LED
Hardware Setup
I/O Board Installation
An ATEN 16 x 16 Modular Matrix Switch is used as an example in the
instructions below. For a list of compatible Modular Matrix Switches,
please visit our official website.
1. Power off the Modular Matrix Switch.
Note: The VM7814 and VM8814 are hot-swappable.
2. On the rear of the Modular Matrix Switch, unscrew the two Phillips
head screws and remove a back panel cover.
3. Slide the VM7814 into any of the Input Board Slots (4 upper slots),
and the VM8814 into any of the Output Board Slots (4 lower slots),
until they secure in place.
4. Tighten the screws on the I/O boards to fasten them to the Modular
Matrix Switch.
5. To install more I/O boards, repeat steps 2 to 4.
6. Proceed to the next section to install a source and a display device.
VM7814 Front View VM8814 Front View
1
23
1
23
Package Contents
1 VM7814 HDMI Input Board or VM8814 HDMI Output Board
4 Terminal Blocks
4 HDMI LockPro
1 User Instructions

Support and Documentation
Notice
All information, documentation,
firmware, software utilities, and
specifications contained in this
package are subject to change
without prior notification by
the manufacturer.
To reduce the environmental
impact of our products, ATEN
documentation and software can
be found online at
http://www.aten.com/
download/
Technical Support
www.aten.com/support
© Copyright 2017 ATEN®International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other trademarks
are the property of their respective owners.
This product is RoHS compliant.
Source and Display Device Installation
1. Connect your A/V source device to the HDMI and audio input ports of the VM7814.
2. Connect your display device to the HDMI output port of the VM8814.
3. Connect your speakers / audio output device to the Audio output port of the VM8814.
4. Power on the Modular Matrix Switch and all devices in the installation.
2
3
1
4
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시
기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Scan for
more information
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
Warning: Operation of this equipment in a residential environment could cause radio interference.
Suggestion: Shielded twisted pair (STP) cables must be used with the unit to ensure compliance with FCC & CE
standards.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.