Atlantic Navilink A59 User manual

For professionals and the user
To be kept by the user for future reference
EN
074208
074231
074232
REFERENCE GUIDE
Navilink A59
Intelligent Room temperature Controller
1846_EN_9
12/10/2020

- 2 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
Description of the equipment
►
General characteristics
Frequency: 868 MHz. Radiofrequency output: 5 mW maximum.
fig. 1 - Dimensions in mm
102
102
22
(51)
Trou de
fixation vis
()3.1
( )60
( )3.1
Trou de fixation
vis
Contents
Description of the equipment 2
General characteristics . . . . . . . . . . . . . . . . . . . . . 2 Display Description . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly and connections 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Opening the sensor . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the sensor with batteries . . . . . . . . . . . . . . . 4
Using the sensor with mains power. . . . . . . . . . . . 5
Attaching to a wall . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wireless connection 7
Room sensor pairing basics . . . . . . . . . . . . . . . . . 7
Pairing a sensor with a HP / Boiler . . . . . . . . . . . . 8
Pairing a 2nd sensor . . . . . . . . . . . . . . . . . . . . . . . 10
Installer Menu 12
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pairing a sensor . . . . . . . . . . . . . . . . . . . . . . . . . 14
Resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sending an io-homecontrol® key . . . . . . . . . . . . 16
Receiving an io-homecontrol® key . . . . . . . . . . . 17
Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pairing procedure ... . . . . . . . . . . . . . . . . . . . . . . 19
How to Use 20
screw hole
Mounting Mounting
screw hole
Adjusting the setpoint via the Advanced Menu:
Manual mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the setpoint via the Simplified Menu:
Direct setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Holiday mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Error List 22

- 3 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
Features
• Holiday mode
• Navigation
• Changing mode
(OFF, Heating, Cooling)
• Increase the setpoint
• Go to next screen
• Reduce the setpoint
• Back to previous screen
►
Display Description
Symbols Definitions
• Holiday mode activated
• Information
• Installer menu
• Cooling mode*
• Heating mode
• Comfort mode Cooling activated*
• Comfort mode Heating activated
• ECO mode Heating/Cooling activated
• Timer programming mode
• Manual mode
• Setpoint value
• Screensaver / Ambient temperature
* If installation allows

- 4 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Installation
The sensor must be installed in the living room area
on an unobstructed wall. It must be installed so as to
be easily accessible. Choose a location with the fewest
possible obstacles to good transmission. Comply with
the following points:
• Avoid proximity to electrical cables, strong magnetic
fields or devices such as computers, televisions or
microwave ovens, etc.
• Avoid any zones of interference caused by large
metallic objects or buildings containing fine metallic
mesh or reinforcing (e.g. glass or special concrete).
• The distance between the transmitter and the receiver
must not exceed 30 m or 2 storeys.
• Do not install the appliance inside a metal casing
(e.g. heat pump).
►
Opening the sensor
Assembly and connections
ClémentTAVERNIER NoticesAtlantic
B : 20 cm miniA : 10 cm C : 150 cm
C
B
A
• Avoid direct sources of heat (chimney, television,
cooking surfaces, sun) and draughty areas (ventilation,
door, etc.).
fig. 2 - Opening the sensor
A
no p
B
►
Using the sensor with batteries
2 AAA LR03 batteries (supplied).
Maintain polarity.
Do not connect the wires.
fig. 3 - Battery-operated sensor
min.
Risk of premature wear of the batteries if the
generator is offpower.

- 5 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Using the sensor with mains power
Power rating 12 - 24V DC.
Type of cable to be used: 0.5 to 1.5 mm2 rigid or 0.5 to 0.75 mm2flexible with rigid end.
Do not use batteries.
Not compatible with boiler.
▼
Cable connection
1. Bare the end of the wires to around 10 mm.
2. Insert the cable ends into the connection terminals ("Push-in" connectors).
fig. 4 - Cable connection
Passage des fils
Bornes de connexion
Passage des fils
fig. 5 - Cable disconnection fig. 6 - Attaching to a wall
▼
Cable disconnection
Use a flat-blade screwdriver.
Rotate the small metal plate while pulling on the cable.
►
Attaching to a wall
Attach the sensor's rear plate using the screws
(not supplied).
Connection terminals
Cable route
Cable route



- 7 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
Wireless connection
►
Room sensor pairing basics
• HP / Boiler --> 1 room sensor
Pair the sensor with the HP / Boiler.
ALFEA
NAIA / NAEMA
(See "Pairing procedure ...", page 19)
• HP / Boiler --> 2 room sensors
Pair the 1st sensor with the HP / Boiler.
ALFEA
NAIA / NAEMA
Pair the 2nd sensor with the 1st sensor.
To pair two devices (HP / Boiler - Sensor or Sensor - Sensor),
both devices must be in pairing mode.
HP
HP
Boiler
Boiler

- 8 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
A
A
A
A
A
A
A
A
A
►
Pairing a sensor with a HP / Boiler
▼
Pairing a 1st sensor with a HP / Boiler
Action Description Display
1
On the boiler or heat pump, start the pairing procedure.
Please refer to the instructions supplied with the product
or "Pairing procedure ...", page 19.
2Default display when sensor is first commissioned.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
3
Select "PAs" using the and buttons.
Wait 5 seconds.
"PAs" flashes. The sensor waits for pairing for 10 minutes.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
4
Select the sensor's zone number
using the and buttons.
Wait 5 seconds.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
or
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Pairing failed.
Restart the procedure from step 2.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
5Pairing was successful.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
6
If only one sensor is to be paired
Select "FIn" (end) using the and buttons.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
If a 2nd sensor is to be paired
Select "Sde" (sensor) using the and buttons.
"Sde" flashes. The sensor waits for pairing for 10 minutes.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A

- 9 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
B
B
B
B
B
B
B
B
▼
Pairing a 2nd sensor
Action Description Display
1Start the pairing procedure on the 1st sensor.
Use the following procedure to pair the 2nd sensor.
2Default display when sensor is first commissioned.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
3
Select "Sde" (sensor) using the and buttons.
Wait 5 seconds.
"Sde" flashes. The sensor waits for pairing for 10 minutes.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
4
Select the sensor's zone number
using the and buttons.
Wait 5 seconds.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
or
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Pairing failed.
Restart the procedure from step 2.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
5Pairing was successful.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
6
Go back to the main screen using the button.
In the event of a failure, restart the procedure from the
beginning.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B

- 10 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
A
A
A
A
A
A
A
B
►
Pairing a 2nd sensor
The installation includes a 1st working sensor.
▼
Procedure for pairing with a 1st sensor
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
2Select "ioAJ" using the button.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
3
Select "oui" (Yes) using the and buttons.
Wait 5 seconds.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
4"Sde" (sensor) flashes. The sensor waits for pairing for 10 minutes.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
5Start the pairing procedure on the 2nd sensor ("Pairing a 2nd sensor", page 11).
6
Pairing was successful.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Pairing failed.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
7Select "FIn" (end) using the and buttons.
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A

- 11 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
B
B
B
B
B
B
B
B
▼
Pairing a 2nd sensor
Action Description Display
1Start the pairing procedure on the 1st sensor.
Use the following procedure to pair the 2nd sensor.
2Default display when sensor is first commissioned.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
3
Select "Sde" (sensor) using the and buttons.
Wait 5 seconds.
"Sde" flashes. The sensor waits for pairing for 10 minutes.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
4
Select the sensor's zone number
using the and buttons.
Wait 5 seconds.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
or
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Pairing failed.
Restart the procedure from step 2.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
5Pairing was successful.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
6
Go back to the main screen using the button.
In the event of a failure, restart the procedure from the
beginning.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B

- 12 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
Installer Menu
Access the Installer Menu by pressing and simultaneously during 3 seconds.
When the Installer Menu is active, the symbol appears.
Quit the Installer Menu by pressing and simultaneously during 3 seconds.
+
+
+
page 13 page 14 page 15 page 16 page 17 page 18
Calibration Pairing Resetting Send key Receive key Version
5 secs. 5 secs. 5 secs. 5 secs. 5 secs.
failed
failed failed
10 mins.
max.
10 mins.
max.
10 mins.
max.

- 13 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Calibration
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Select "EtAI" (calibration) using the button.
3
Adjust the temperature using the and buttons.
Wait 5 seconds.
4The sensor is calibrated.
5Quit the Installer Menu by pressing and simultaneously
during 3 seconds.

- 14 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Pairing a sensor
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Select "ioAJ" using the button.
3
Select "oui" (yes) using the and buttons.
Wait 5 seconds.
4"Sde" (sensor) flashes. The sensor waits for pairing for 10 minutes.
5
Pairing was successful.
Pairing failed.
6Go back to the main screen using the button.
In the event of a failure, restart the procedure from the beginning.

- 15 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Resetting
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Select "init" (reset) using the button.
3
Select "oui" (yes) using the and buttons.
Wait 5 seconds.
5The sensor is reset.

- 16 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
• ADVANCED PARAMETERS - HOME AUTOMATION OPTIONS
Security key:
The io-homecontrol® Wireless protocol has built-in security to avoid interfering with nearby equipment.
Where various io-homecontrol® devices are used, the first installed device will generate a
unique "security key" for all devices in the house. Existing equipment must share this security key with the
equipment to be added.
This section is reserved for competent users of io-homecontrol® technology and offers various services
covered by this key.
Please refer to the section on pairing io-homecontrol® devices.
►
Sending an io-homecontrol® key
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Select "ioEn" using the button.
3
Select "oui" (yes) using the and buttons.
Wait 5 seconds.
4The io-homecontrol® key send sequence starts.
5
The io-homecontrol® key was sent successfully.
The io-homecontrol® key was not sent.
6Go back to the main screen using the button.
In the event of a failure, restart the procedure from the beginning.

- 17 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Receiving an io-homecontrol® key
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Select "iorE" using the button.
3
Select "oui" (yes) using the and buttons.
Wait 5 seconds.
4The io-homecontrol® key receive sequence starts.
5
The io-homecontrol® key was received successfully.
The io-homecontrol® key was not received.
6Go back to the main screen using the button.
In the event of a failure, restart the procedure from the beginning.

- 18 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Version
Action Description Display
1Access the Installer Menu by pressing and simultaneously
during 3 seconds.
2Access the "Version" screen using the button.
3Quit the Installer Menu by pressing and simultaneously
during 3 seconds.

- 19 -
Navilink A59 / REFERENCE GUIDE / 1846 - EN
►
Pairing procedure ...
▼
...with an heat pump alféa A.I.
For more information, please refer to the instructions supplied with the appliance.
▼
...with a Navipass io-homecontrol®
For more information, please refer to the instructions supplied with Navipass io-homecontrol®.
Connectivities Connection Settings
To connect a room sensor, go to the menu:
"Settings" > "Connectivities" > "Connection".
The appliance waits for pairing for 10 minutes.
The "Connection" menu is no longer accessible if a sensor has already paired.
Connection
Quit
Settings
Connectivities
>3s
1
Place the NAVIPASS IO waiting for pairing.
Press key 1 during 3 seconds.
Release.
LED 1 flashes green quickly.

- 20 - Navilink A59 / REFERENCE GUIDE / 1846 - EN
How to Use
►
Adjusting the setpoint via the Advanced Menu: Manual mode
The exemption allows you to change the setpoint for a period of 24 hours.
Action Description Display
1Press or .
2The setpoint flashes.
Adjust the setpoint using the and buttons.
3
Once the setpoint has been selected, wait 5 seconds.
It stops flashing.
The setpoint is changed for a period of 24 hours.
At the end of the exemption period, it returns to the original state and the "hand"
symbol disappears.
►
Adjusting the setpoint via the Simplified Menu: Direct setpoint
Action Description Display
1Press or .
2The setpoint flashes.
Adjust the setpoint using the and buttons.
3
Once the setpoint has been selected, wait 5 seconds.
It stops flashing.
The setpoint was changed.