Atlantis Land ISDN Router with 10/100 LAN port ATLMMR... User manual

ISDN Router
with 10/100 LAN port
User’s Manual V1.0

COPYRIGHT
The Atlantis Land logo is a registered trademark of Atlants Land SpA. All other names mentioned mat be
trademarks or registered trademarks of their respective owners. Subject to change without notice. No
liability for technical errors and/or omissions. Copyright 2002 by this company.
DISCLAIMER
This company makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, this company reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
SUPPORT
If you have any problems with the ADSL Router, please consult this manual.
If you continue to have problems you should contact the dealer where you bought this ADSL Router. If
you have any other questions you can contact the Atlantis Land company directly at the following address:
AtlantisLand spa
Via Gandhi 5 Ing2,Scala A
20017 Mazzo di Rho(MI)
Tel: [phone](help desk)
Fax: [phone]
Email: [email protected] or [email protected]
WWW: http://www.atlantis-land.com or www.atlantisland.it
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.

ii
Table of Contents
CHAPTER 1............................................................................................................................................... 1
INTRODUCTION ................................................................................................................................... 1
1.1 An overview of the ISDN Router........................................................................................................ 1
1.2 Package contents ................................................................................................................................. 1
1.3 ISDN Router Features ......................................................................................................................... 2
1.4 ISDN Router Application.................................................................................................................... 2
CHAPTER 2............................................................................................................................................... 3
USING THE ISDN ROUTER ................................................................................................................. 3
2.1 Cautions for using the ISDN Router ................................................................................................... 3
2.2 The front LEDs.................................................................................................................................... 3
2.3 The rear ports....................................................................................................................................... 4
2.4 Cabling ................................................................................................................................................ 4
CHAPTER 3............................................................................................................................................... 6
CONFIGURATION................................................................................................................................. 6
3.1 Before Configuration........................................................................................................................... 6
3.2 Configuring with GUI program......................................................................................................... 10
CHAPTER 4............................................................................................................................................. 21
REMOTE CONFIGURATION ............................................................................................................... 21
4.1 Remote Office Access by ISDN........................................................................................................ 21
4.2 Advanced Options for Remote Office Access Profiles ..................................................................... 23
4.3 Deleting Remote Office Access Profile ............................................................................................ 25
CHAPTER 5............................................................................................................................................. 26
DIAL-IN USER ACCESS CONFIGURATION......................................................................................... 26
5.1 Configuring a Dial-in User Profile.................................................................................................... 26
5.2 Deleting Dial-in User Profiles........................................................................................................... 28
5.3 Packet Filtering.................................................................................................................................. 28
CHAPTER 6............................................................................................................................................. 30
MANAGEMENT .................................................................................................................................. 30
6.1 How to Upgrade the Firmware.......................................................................................................... 30
6.3 How to Change ISDN Router Manager Password ............................................................................ 31
6.4 What if I Forget the Password? ......................................................................................................... 31
CHAPTER 7............................................................................................................................................. 32
TROUBLESHOOTING ......................................................................................................................... 32
ATLMMR_ME01

1
Chapter 1
Introduction
1.1 An overview of the ISDN Router
The device is a small desktop router that sits between your local Ethernet network and a remote
network (For example, the Internet or a remote office). It contains an ISDN S/T interface, a 10/100
Base-T LAN port, and an auxiliary port for a directly connected management console.
Data comes into ISDN Router from the LAN and then is “routed” to the remote network, and vice
versa. In addition to its capability to route IP traffic, it also acts as a bridge for other network protocols,
such as Appletalk or SNA.
The main functions of the device are to support your LAN to access the Internet, to support
remote users to dial in and to access resources on your LAN, and to support communications among
branch offices.
The most common use for the device is to provide Internet access, so that everyone on your LAN
can surf the web, send/receive e-mail or files. It automatically acquires the necessary IP address when
the connection to the Internet is established. You don’t need to apply for and assign an IP address to
each PC or workstation on your network.
The device supports “bandwidth on demand”. For example, any user’s initial intent to access to
the Internet will trigger a B-channel connection to the Internet to be set up. As the traffic builds up
(For example, more users try to access the Internet, or the same user generates a lot of traffic), it will
establish a second connection through the other B-channel. As traffic decreases, one B-channel will be
taken down, until finally, after a configurable period of inactivity, the remaining B-channel will also
be disconnected.
1.2 Package contents
1. ISDN Router
2. AC Power Adapter
3. RS-232 cable (Null type)
4. RJ-45 ISDN cable
5. RJ-45 LAN cable
6. CD-ROM containing the on-line manual
7. Quick Start Guide

2
1.3 ISDN Router Features
The ISDN Router provides the following features
 The router equipped with a single ISDN Basic Rate Interface (2B+D) that supports S/T interface
specification, would support European ISDN requirements.
 Supports remote access functions among branch offices and allows remote users to dial-in to your network.
 Supports IP sharing function, allowing multiple users share one Internet account.
 Supports industry standard Point-to-Point Protocol (PPP) and Multilink PPP.
 Supports Dial-on-Demand and Bandwidth on Demand function.
 User-friendly management through web-based configurator, telnet management, console port management,
and remote upgrades.
 PAP/CHAP/MS-CHAP, Call Back, IP Packet Filtering, and Caller ID Authentication for firewall security.
 Supports operating systems such as Windows 95/98/NT/2000/ME, Mac, Unix and Linux
1.4 ISDN Router Application

3
Chapter 2
Using the ISDN Router
2.1 Cautions for using the ISDN Router
Do not place the ISDN Router under high humidity and high temperature.
Do not use the same power source for ISDN Router with other equipment.
Do not open or repair the case yourself. If the ISDN Router is too hot, turn off the power
immediately and have a qualified serviceman repair it.
Place the ISDN Router on the stable surface.
Only use the power adapter that comes with the package.
2.2 The front LEDs
1 2 3 4 5 6 7
LED Meaning
1 Power Lit when AC power is connected
2 LAN /
100/10
Lit Green when connected at 100 Mbps
Lit Yellow when connected at 10 Mbps
3 LAN /
ACT
Lit when connected to a LAN device
Flashes when sending/receiving data
4 LAN /
COL
Flashes when collisions happen
5 ISDN /
SYNC
Lit when ISDN Layer 1 is activated
6 ISDN /
B1
Flashes when B1 channel is in use
7 ISDN /
B2
Flashes when B2 channel is in use

4
2.3 The rear ports
Power
(jack)
Connect the supplied power adapter to this jack
Console
(port)
Connect the supplied Null type RS-232 cable to this
port when connecting to a PC’s RS-232 port (9-pin
serial port).
ISDN So
(RJ-45
connector)
Connect an RJ-45 cable to this port when
connecting to the ISDN.
LAN
(RJ-45
connector)
Connect an UTP Ethernet cable to this port when
connecting to a LAN such as an office or home
network.
2.4 Cabling
Now you should be ready to connect your ISDN Router on your LAN and ISDN wall jacks. Follow these
steps to install:
˙Attach the ISDN line to the ISDN connector (S/T interface).
˙
Connect the PC to the RJ-45 LAN connector. Two or more PCs can connect to a multi-port Hub first and
then uplink (cascade) port on the hub must be connected to ISDN Router port.
˙Plug the power adapter into a wall outlet and into the AC connector on the back of ISDN Router.
˙The Auxiliary connector is only used to connect a terminal to run the Command Line Interface using
the null modem cable. (This is an optional connection.)

5
˙There is a DIP switch located on the rear panel for setting the terminating resistor.
You only need to adjust this switch if there are two or more external ISDN equipments attached to the
local telephone line.

6
Chapter 3
Configuration
3.1 Before Configuration
This section describes the configuration required by LAN-attached PCs that communicate with ISDN
Router, either to configure ISDN Router, or for network access. These PCs must have an Ethernet interface
installed properly, be connected to ISDN Router either directly or through an external repeater hub, and have
TCP/IP installed and configured to obtain an IP address through a DHCP server.
Directly connect a Windows OS to ISDN Router. If TCP/IP is not already installed, follow the steps below
for its installation.
Any TCP/IP capable workstation can be used to communicate with or through ISDN
Router. To configure other types of workstations, please consult the manufacturer’s
documentation
Configuring PC in Windows 95/98/ME
1. Go to Start/Settings/Control
Panel. In the Control Panel
double-click on Network and
choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or any
Network Interface Card (NIC)
in your PC.

7
3. Select the Obtain an IP
address automatically radio
button.
4. Then select the DNS
Configuration tab.
5. Select the Disable DNS radio
button and click OK to finish
the configuration.

8
Configuring PC in Windows NT4.0
1. Go to Start/Settings/ Control
Panel. In the Control Panel
double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and
click Properties.
3. Select the Obtain an IP
address from a DHCP server
radio button and click OK.

9
Configuring PC in Windows 2000
1. Go to Start/Settings/Control
Panel. In the Control Panel
double-click on Network and
Dial-up Connections.
2. Double-click Local Area
Connection.
3. In the Local Area Connection
Status window click
Properties.
4. Select Internet Protocol
(TCP/IP) and click Properties.

10
5. Select the Obtain an IP
address automatically and the
Obtain DNS server address
automatically radio buttons.
6. Click OK to finish the
configuration.
3.2 Configuring with GUI program
3.2.1 Using Different Browsers for ISDN Router
To configure your ISDN Router, you can use a popular browser, such as Netscape 4.x and Internet
Explorer 5.x. The following describes how to use it to start “ISDN Router Manager” through IE or Navigator.
Netscape Navigator 4.x:
In the Location box (where you normally enter the URL address), enter the default private IP address of
ISDN Router followed by hitting the return key:
http://192.168.168.230
Internet Explorer 5.x:
In the Address box (where you normally enter the URL address), enter the default private IP address of
ISDN Router followed by hitting the return key:
http://192.168.168.230

11
3.2.2 Password
A password screen will ask you to log on after you enter the default IP address described above. If you are
logging on for the first time, you should accept the factory default password (which is “password”). The
password is always displayed as a string of asterisks (“*”). Clicking the Log On button will begin the
Configurations for ISDN Router.
The next time you log in, even if you have modified the password, the default password (“password”) will
still be used as the default. You need to change it to the correct password before you will be let in. If you forget
the password, you need to follow the steps described in the latter chapter to be able to log on.
3.2.3 Customize User Interface
When you log on for the first time, click “Customize User Interface” in the SYSTEM TOOLS bar on the
left side of the screen, allowing you to customize ISDN Router Manager to suit your own specific needs: The
selections you make determine what configuration menus and buttons will appear in the screen. For example, if
you select Basic Internet Access only, the interface will only display buttons that you need for basic Internet
access.
If you subsequently use ISDN Router Manager to configure ISDN Router for other applications, you can
return to this screen to “re-customize” your interface by selecting Customize User Interface from the
SYSTEM TOOLS Menu.
3.2.4 Basic Internet Access Configuration
What is Basic Internet Access? It means accessing the Internet, surfing the web, accessing a remote FTP
server (to send or receive files), and sending and receiving e-mail. These are the tasks that users perform most.

12
When you apply for an account with your Internet Service Provider (ISP), you will be given the necessary
information, including your account name, account password, and the ISP’s local access ISDN telephone
number. Have these available and then follow the steps below.
Step 1: When you logon, select Customize User Interface in the SYSTEM TOOLS Menu. Accept the
Basic Internet Access selection and click Next. The configuration window will be displayed,
Step 2: Select the ISDN switch type that your ISP will tell you.
Step 3: Select the number of the directory phone numbers and enter the directory phone numbers in the
corresponding blanks.
Step 4: Enter the following information:
Remote Phone Number: the ISDN telephone number of your ISP.
ISP Account Name: the username of your ISP account.
ISP Account Password: the password of your ISP account.
Step 5: Click Apply and Test.
After the successful Apply and Test, any users in the LAN should restart their PC. Now you can surf in
the Web, receive E-mails, or transmit files. For more advanced configurations, refer to the following context.
3.2.5 Internet Access with Advanced Configuration
Step 1: When you logon, select Customize User Interface in the SYSTEM TOOLS Menu. Accept the
Internet Access with Advanced Configuration selection and click Next. The configuration window
will be displayed. Skip to Step 5 if you have already completed Basic Internet Access Configuration
described in the previous section.

13
Step 2: Select the ISDN switch type that your ISP will tell you.
Step 3: Select the number of the directory phone numbers and enter the directory phone numbers in the
corresponding blanks.
Step 4: Enter the following information:
Remote Phone Number: the ISDN telephone number of your ISP.
ISP Account Name: the username of your ISP account.
ISP Account Password: the password of your ISP account.
Step 5: Click Advanced and the following configuration window will appear.
Step 6: Set Multilink Usage parameters. This determines how the device utilizes the two B channels for
your Internet connection. Available options are:

14
One B Channel Only:
Two B Channels Only When Needed:
Always two B Channels:
Step 7: Select Data Service. Available options are Data Over Voice Channel, 64K , 56K , and Auto.
Recommended selection is Auto.
Step 8: Enter Remote Sub Address Number if necessary.
Step 9: Select STAC compression option.
Step 10: Set Idle Timeout number. The range is from 0 to 3600 seconds.
Step 11: Select Advice of Charge Support option and enter the Unit Price and Currency in the
corresponding blanks if the selection is Yes.
Step 12: Click OK to return to the main configuration screen and skip to next step. Otherwise click
Alternative Number if there is one or more alternative remote phone numbers. Enter the alternative
remote phone number in the corresponding blanks. Then press OK to return to the previous screen. Again
press OK to back to main configuration screen.
Step 13 Click Apply and Test
3.2.6 IP Configuration for Internet Access
Using IP options in the Menu Window, you can assign a public IP address to ISDN Router, modify the
private IP address, DNS addresses, and enable or disable DHCP.
Step 1: Select Internet Access with Advanced Configuration from ISDN Router Manager. Then click
IP from the Menu Window.
Step 2: The Advanced Internet Access Setup screen appears:

15
To install public servers on your network (For Example, Web or ftp
servers), you need to apply for an IP address for each server plus one
for the LAN port. All these public IP addresses have to belong to the
same IP network
Set the following parameters:
Public IP Address: the public IP address for the LAN interface on ISDN Router.
Public IP Netmask: the network mask for the public network address on LAN.
Private IP Address: the private IP address for the LAN interface on ISDN Router. The default private IP
address is 192.168.168.230.
Private IP Netmask: the network mask for your private network. Its value is 255.255.255.0, and cannot
be changed.
Primary DNS IP Address: the IP address of the primary Domain Name Server (DNS). If properly
configured, when a device reboots and acquires the IP address from ISDN Router, the IP addresses of
both the primary and the secondary DNS server will be provided for client workstations or PCs.
Secondary DNS IP Address: the IP address of the secondary domain name server.
DHCP: If you want to act, as a DHCP server and assigns private IP addresses to any requesting DHCP
client, make sure DHCP is enabled. When enabled, it will provide an IP address, network mask, gateway
address (ISDN Router’s private IP address), and DNS addresses to any workstations on the local area
network that are configured as a DHCP client. Devices on your network that are configured with public
IP addresses are not DHCP clients. Therefore, you need to assign their IP addresses, network mask, and
default gateway’s IP address, primary and secondary DNS IP addresses manually.
IP Address Assignment-High & Low: the setting about the maximum and minimum of private IP
address for each client PC or workstation in the LAN. The range is from 1 to 254.
Step 3: Click Routing,Address Translation or Static DHCP if it is necessary to set these
configurations. Otherwise click Apply to confirm the configuration and return to the main configuration
screen.
3.2.7 The IP Routing Table
The IP Routing Table contains all the information that the ISDN Router needs to route an IP data
packet. You can view the IP Routing Table by clicking on the Routing button at the bottom of the
Advanced Internet Access Setup screen (described in the previous section). From this screen, you can
also add new routing entries to the table. The following screen shows an example of the IP Routing Table.

16
An entry for a specific host or network may be added manually. An “S” in the Flags field indicates this
“static route”. Other flag field entries are “H” for host, and “G” for gateway.
Follow the steps to add or to change the default route or add a static route:
Step 1: Click the Add button in the IP Routing Table screen to display the following screen:
Step 2: Enter the following information:
Default Route: select if you want to specify a new default route. Note that the Remote IP Address and
Remote IP netmask fields do not appear if you select this option. CAUTION: Mis-configuring the default
route may result in abnormal system behavior and/or unnecessary telephone charges.
Static Route: select if you want to add a static route.
Remote IP Address: the remote IP address of the new route.
Remote IP Netmask: the IP netmask of the new route.

17
Gateway: identifies if the gateway is an IP address or interface.
Hop Count: the maximum number of hops for this route.
Step 3 Click APPLY.
3.2.8 IP Address Translation Configuration
For security and economic purposes, the device supports Single User Account feature (SUA). Multiple
users in the LAN can share a public IP address from ISP and Internet users would view the whole LAN as
a big “device”.