Atlantis Land Compact Router ADSL A02-RA110 User manual

COMPACT ROUTER
ADSL
A02-RA110
USER’S MANUAL
A02-RA110 _ME01

COMPACT ROUTER ADSL
INDEX
CHAPTER 1: GETTING TO KNOW THE ADSL ROUTER 1
1.1 Introducing the Compact Router ADSL 1
1.2 Package Contents 1
1.3 Features of the Compact Router ADSL 2
1.4 Applications for the ADSL Router 4
1.4.1 Internet Access 4
CHAPTER 2: USING COMPACT ROUTER ADSL 6
2.1 Cautions for using the Compact Router ADSL 6
2.2 The Front Panel LEDs 6
2.3 The Rear Ports 7
2.4 Cabling 8
CHAPTER 3: INTRODUCING THE WEB CONFIGURATOR 9
3.1 Web Configurator Overview 9
3.2 Configuring PC in Windows 10
3.2.1 For Windows 95/98/ME 10
3.2.2 For Windows NT4.0 10
3.2.3 For Windows 2000 10
3.2.4 For Windows XP 11
3.3 Factory Default Settings 14
3.3.1 Username and Password 14
3.3.2 LAN and WAN Port Addresses 14
3.4 Information from the ISP 14
3.5 Accessing the ADSL Router Web Configurator 15
3.6 Navigating the Compact Router ADSL Web Configurator 16
3.7 Configuring Password 17
3.8 Resetting the ADSL Router 18
3.8.1 Using The Reset Button 18
CHAPTER 4: WIZARD SETUP 19
4.1 Wizard Setup Introduction 19

COMPACT ROUTER ADSL
4.2 Encapsulation 19
4.2.1 ENET ENCAP 19
4.2.2 PPP over Ethernet 19
4.2.3 PPPoA 19
4.2.4 RFC 1483 20
4.3 Multiplexing 20
4.3.1 VC-based Multiplexing 20
4.3.2 LLC-based Multiplexing 20
4.4 VPI and VCI 20
4.5 Wizard Setup Configuration: First Screen 20
4.6 IP Address and Subnet Mask 22
4.7 IP Address Assignment 22
4.7.1 IP Assignment with PPPoA or PPPoE Encapsulation 23
4.7.2 IP Assignment with RFC 1483 Encapsulation 23
4.7.3 IP Assignment with ENET ENCAP Encapsulation 23
4.7.4 Private IP Addresses 23
4.8 Nailed-Up Connection (PPP) 23
4.9 NAT 24
4.10 Wizard Setup Configuration: Second Screen 24
4.10.1 PPPoE 24
4.10.2 RFC 1483 25
4.10.3 ENET ENCAP 27
4.10.4 PPPoA 28
4.11 DHCP Setup 30
4.11.1 IP Pool Setup 30
4.12 Wizard Setup Configuration: Third Screen 30
4.13 Wizard Setup Configuration: Connection Tests 33
4.14 Test Your Internet Connection 33
CHAPTER 5: LAN SETUP 34
5.1 LAN Overview 34
5.1.1 LANs, WANs and the ADSL Router 34
5.2 DNS Server Address 35
5.3 DNS Server Address Assignment 35
5.4 LAN TCP/IP 36
5.4.1 Factory LAN Defaults 36
5.4.2 IP Address and Subnet Mask 36
5.4.3 RIP Setup 36
5.4.4 Multicast 37
5.5 Configuring LAN 38

COMPACT ROUTER ADSL
CHAPTER 6: WAN SETUP 40
6.1 WAN Overview 40
6.2 PPPoE Encapsulation 40
6.3 PPTP Encapsulation 40
6.4 Traffic Shaping 41
6.5 Configuring WAN Setup 42
CHAPTER 7: NETWORK ADDRESS TRANSLATION (NAT) 46
7.1 NAT Overview 46
7.1.1 NAT Definitions 46
7.1.2 What NAT Does 47
7.1.3 How NAT Works 47
7.1.4 NAT Application 48
7.1.5 NAT Mapping Types 49
7.2 SUA (Single User Account) Versus NAT 49
7.3 SUA Server 50
7.3.1 Port Forwarding: Services and Port Numbers 50
7.3.2 Configuring Servers Behind SUA (Example) 51
7.4 Selecting the NAT Mode 52
7.5 Configuring SUA Server 53
7.6 Configuring Address Mapping 54
7.7 Editing an Address Mapping Rule 56
CHAPTER 8: SECURITY 58
CHAPTER 9: DYNAMIC DNS SETUP 59
9.1 Dynamic DNS 59
9.1.1 DYNDNS Wildcard 59
9.2 Configuring Dynamic DNS 59
CHAPTER 10: TIME AND DATE SETUP 61
10.1 Configuring Time Zone 61
CHAPTER 11: REMOTE MANAGEMENT CONFIGURATION 64
11.1 Remote Management Overview 64
11.1.1 Remote Management Limitations 64
11.1.2 Remote Management and NAT 64

COMPACT ROUTER ADSL
11.1.3 System Timeout 65
11.2 Telnet 65
11.3 FTP 65
11.4 Web 65
11.5 Configuring Remote Management 65
CHAPTER 12: MAINTENANCE 67
12.1 Maintenance Overview 67
12.2 System Status Screen 67
12.2.1 System Statistics 69
12.3 DHCP Table Screen 70
12.4 Diagnostic Screens 71
12.4.1 Diagnostic General Screen 71
12.4.2 Diagnostic DSL Line Screen 72
12.5 Firmware Screen 74
APPENDIX A: TROUBLESHOOTING 76
A.1 Using LEDs to Diagnose Problems 76
A.1.1 Power LED 76
A.1.2 LAN LED 76
A.1.3 DSL LED 76
A.2 Telnet 77
A.3 Web Configurator 77
A.4 Login Username and Password 78
A.5 LAN Interface 79
A.6 WAN Interface 79
A.7 Internet Access 80
A.8 Remote Management 80
A.9 Remote Node Connection 81
APPENDIX B: TECHNICAL FEATURES 82
APPENDIX C:SUPPORT 83
A02-RA110_ME01 (V1.0 July 2004)

COMPACT ROUTER ADSL

COMPACT ROUTER ADSL
Copyright
The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other
names mentioned mat be trademarks or registered trademarks of their respective
owners. Subject to change without notice. No liability for technical errors and/or
omissions.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
FCC Warning
This equipment has been tested and found to comply with the regulations for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at his own expense.

COMPACT ROUTER ADSL
A02-RA110 Pag. 1
CHAPTER 1: Getting to Know the ADSL Router
This chapter describes the key features and applications of ADSL Router.
1.1 Introducing the Compact Router ADSL
Broadband Sharing and IP sharing
The Compact Router ADSL supports 1 port 10/100 Mbps auto-negotiating Fast
Ethernet for connection to your PC or LAN and downstream (with built-in ADSL
modem) rate up to 8Mbps. Power by NAT technology, dozens of network users
can surf on the Internet and share the ADSL connection simultaneously by using
one ISP account and one single IP address.
Easy Configuration and Management
Support web based GUI and Telnet for configuration and management.
The web browser-based Graphical User Interface provides easy management
and is totally independent of the operating system platform you use.
Also supports remote management (Web and telnet) capability for remote user to
configure and manage this product. It incorporates besides a client Dynamic
DNS.
1.2 Package Contents
• Compact Router ADSL
• One CD-ROM containing the online manual
• One Quick Start Guide
• One RJ-11 ADSL/telephone cable
• One CAT-5 LAN cable
• One AC-DC power adapter (9VDC, 1A)
If any of the above items are missing, please contact your reseller.

COMPACT ROUTER ADSL
A02-RA110 Pag. 2
1.3 Features of the Compact Router ADSL
The following sections describe the features of the ADSL Router.
High Speed Internet Access: The ADSL Router can support downstream
transmission rates of up to 8Mbps and upstream transmission rates of 832 Kbps.
PPPoE Support (RFC2516): PPPoE (Point-to-Point Protocol over Ethernet)
emulates a dial-up connection. It allows your ISP to use their existing network
configuration with newer broadband technologies such as ADSL. The PPPoE
driver on the ADSL Router is transparent to the computers on the LAN, which see
only Ethernet and are not aware of PPPoE thus saving you from having to
manage PPPoE clients on individual computers.
Network Address Translation (NAT): Network Address Translation (NAT) allows
the translation of an Internet protocol address used within one network (for
example a private IP address used in a local network) to a different IP address
known within another network (for example a public IP address used on the
Internet).
10/100M Auto-negotiation Ethernet/Fast Ethernet Interface: This auto-
negotiation feature allows the ADSL Router to detect the speed of incoming
transmissions and adjust appropriately without manual intervention. It allows data
transfer of either 10 Mbps or 100 Mbps in either half-duplex or full-duplex mode
depending on your Ethernet network.
Dynamic DNS Support: With Dynamic DNS support, you can have a static
hostname alias for a dynamic IP address, allowing the host to be more easily
accessible from various locations on the Internet. You must register for this
service with a Dynamic DNS client.
Multiple PVC (Permanent Virtual Circuits) Support
The ADSL Router supports up to 8 PVC’s.
ADSL Standards: Full-Rate (ANSI T1.413, Issue 2; G.dmt (G.992.1) with line rate
support of up to 8 Mbps downstream and 832 Kbps upstream. G.lite (G.992.2)
with line rate support of up to 1.5Mbps downstream and 512Kbps upstream.
Supports Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.994.1
and G.996.1 (for ISDN only); G.991.1;G.lite (G992.2)).Supports OAM F4/F5 loop-
back, AIS and RDI OAM cells.ATM Forum UNI 3.1/4.0 PVC.Supports up to 8
PVCs (UBR, CBR, VBR).Multiple Protocols over AAL5 (RFC 1483).PPP over
AAL5 (RFC 2364).PPP over Ethernet (RFC 2516).

COMPACT ROUTER ADSL
A02-RA110 Pag. 3
DHCP Support: DHCP (Dynamic Host Configuration Protocol) allows individual
clients (computers) to obtain TCP/IP configuration at start-up from a centralized
DHCP server. The ADSL Router has built-in DHCP server capability enabled by
default. It can assign IP addresses, an IP default gateway and DNS servers to
DHCP clients. The ADSL Router can now also act as a surrogate DHCP server
(DHCP Relay) where it relays IP address assignment from the actual real DHCP
server to the clients.
IP Alias: IP Alias allows you to partition a physical network into logical networks
over the same Ethernet interface. The ADSL Router supports three logical LAN
interfaces via its single physical Ethernet interface with the ADSL Router itself as
the gateway for each LAN network.
IP Policy Routing (IPPR): Traditionally, routing is based on the destination
address only and the router takes the shortest path to forward a packet. IP Policy
Routing (IPPR) provides a mechanism to override the default routing behavior
and alter the packet forwarding based on the policy defined by the network
administrator.
Protocol Support: PPP (Point-to-Point Protocol) link layer protocol.PPP over
PAP (RFC 1334).PPP over CHAP (RFC 1994).RIP I/RIP II.IGMP Proxy,ICMP
support,MIB II support (RFC 1213),PPPoE feature,PPPoE idle time out,PPPoE
dial on demand.
Networking Compatibility: The ADSL Router is compatible with major ADSL
DSLAM (Digital Subscriber Line Access Multiplexer) providers.
Multiplexing: The ADSL Router supports VC-based and LLC-based multiplexing.
Encapsulation: The ADSL Router series supports PPPoA (RFC 2364 - PPP over
ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM, MAC encapsulated
routing (ENET Encapsulation) as well as PPP over Ethernet (RFC 2516).
Network Management: Embedded Web Configurator,CLI (Command Line
Interpreter),SNMP manageable,DHCP Server/Client,Built-in Diagnostic Tools.
Syslog, TFTP/FTP server, firmware upgrade and configuration backup/support
supported.
Diagnostics Capabilities: The ADSL Router can perform self-diagnostic tests.
These tests check the integrity of the following circuitry:

COMPACT ROUTER ADSL
A02-RA110 Pag. 4
 FLASH memory
 ADSL circuitry
 RAM
 LAN port
Filters: The ADSL Router 's packet filtering functions allows added network
security and management.
Ease of Installation: The ADSL Router is designed for quick, intuitive and easy
installation.
Compact Housing: The ADSL Router 's all new compact and ventilated housing
minimizes space requirements making it easy to position anywhere in your busy
office.
1.4 Applications for the ADSL Router
Here are some example uses for which the ADSL Router is well suited.
1.4.1 Internet Access
The ADSL Router is the ideal high-speed Internet access solution. The Compact
Router ADSL Router supports the TCP/IP protocol, which the Internet uses
exclusively. It is compatible with all major ADSL DSLAM (Digital Subscriber Line
Access Multiplexer) providers. A DSLAM is a rack of ADSL line cards with data
multiplexed into a backbone network interface/connection (for example, T1, OC3,
DS3, ATM or Frame Relay). Think of it as the equivalent of a modem rack for
ADSL.

COMPACT ROUTER ADSL
A02-RA110 Pag. 5

COMPACT ROUTER ADSL
A02-RA110 Pag. 6
CHAPTER 2: Using Compact Router ADSL
This chapter describes how to access and navigate the web configurator.
2.1 Cautions for using the Compact Router ADSL
 Do not place the Compact Router ADSL under high humidity and high
temperature.
 Do not use the same power source for Compact Router ADSL with other
equipment.
 Do not open or repair the case yourself. If the Compact Router ADSL is too
hot, turn off the power immediately and have a qualified serviceman repair it.
 Place the Compact Router ADSL on a stable surface.
 Only use the power adapter that comes with the package.
 Do NOT upgrade firmware on any Atlantis Land product over a wireless
connection. Failure of the device may result. Use only hard-wired network
connections.
2.2 The Front Panel LEDs
LED MEANING
POWER Lit when power ON
SYS Lit when system is ready
LAN
Lit when connected to Ethernet device
Green for 100Mbps; Orange for 10Mbps
Blinking when data transmit/received

COMPACT ROUTER ADSL
A02-RA110 Pag. 7
ADSL Lit when successfully connected to an ADSL DSLAM
PPP Lit when there is a PPPoA/PPPoE connection
2.3 The Rear Ports
PORT MEANING
LINE (RJ11) Connect the supplied RJ-11 cable to this port when
connecting to the ADSL/telephone network.
LAN
(RJ-45)
Connect an UTP Ethernet cable to one of the four
LAN ports when connecting to a PC or an
office/home network of 10Mbps or 100Mbps.
RESET After the device has turned on, press it to reset the
device or restore to factory default settings. The
operation is as below:
0-3 seconds: reset the device
3-5 seconds: no action
6 seconds or above: restore to factory default
settings (this is used when you can not login to the
router, e.g. forgot the password)
POWER (jack) Connect the supplied power adapter to this jack.

COMPACT ROUTER ADSL
A02-RA110 Pag. 8
2.4 Cabling
The most common problem is bad cabling or ADSL line. Make sure that all
connected devices are turned on. On the front of the product is a bank of LEDs.
As a first check, verify that the LAN Link and ADSL line LEDs are lit and SYS is
blanking. If they are not, verify that you are using the proper cables.

COMPACT ROUTER ADSL
A02-RA110 Pag. 9
CHAPTER 3: Introducing the Web Configurator
This chapter describes how to access and navigate the web configurator.
3.1 Web Configurator Overview
The embedded web configurator allows you to manage the Compact Router
ADSL from anywhere through a browser such as Microsoft Internet Explorer or
Netscape Navigator. Use Internet Explorer 6.0 and later or Netscape Navigator
7.0 and later versions with JavaScript enabled. It is recommended that you set
your screen resolution to 1024 by 768 pixels.
This section describes the configuration required by LAN-attached PCs that
communicate with the Compact Router ADSL, either to configure the device or for
network access. These PCs must have an Ethernet interface installed properly, be
connected to the ADSL Router either directly or through an external Switch, and
have TCP/IP installed and configured to obtain an IP address through a DHCP
server or a fixed IP address that must be in the same subnet of the Compact
Router ADSL. The default IP address of the Compact Router ADSL is
192.168.1.254 and subnet mask is 255.255.255.0. The best and easy way is to
configure the PC to get an IP address from the ADSL Router. Also make sure you
have UNINSTALLED any kind of software firewall that can cause problems while
accessing the 192.168.1.254 IP address of the router.
Please follow the steps below for PC’s network environment installation. First of
all, please check your PC’s network components. The TCP/IP protocol stack and
Ethernet network adapter must be installed. If not, please refer to MS Windows
related manuals.
Any TCP/IP capable workstation can be used to communicate
with or through the Compact Router ADSL. To configure other
types of workstations, please consult the manufacturer’s
documentation.

COMPACT ROUTER ADSL
A02-RA110 Pag. 10
3.2 Configuring PC in Windows
3.2.1 For Windows 95/98/ME
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on
Network and choose the Configuration tab.
2. Select TCP / IP -> NE2000 Compatible, or the name of any Network
Interface Card (NIC) in your PC.
3. Click Properties.
4. Select the IP Address tab. In this page, click the Obtain an IP address
automatically radio button.
5. Then select the DNS Configuration tab.
6. Select the Disable DNS radio button and click “OK” to finish the
configuration.
3.2.2 For Windows NT4.0
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on
Network and choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a DHCP server radio button and click
“OK”.
3.2.3 For Windows 2000
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on
Network and Dial-up Connections.
2. Double-click LAN Area Connection.

COMPACT ROUTER ADSL
A02-RA110 Pag. 11
3. In the LAN Area Connection Status window, click Properties.
4. Select Internet Protocol (TCP/IP) and click Properties.
5. Select the Obtain an IP address automatically and the Obtain DNS server
address automatically radio buttons.
6. Click “OK” to finish the configuration.
3.2.4 For Windows XP
1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-
click on Network Connections.
2. Double-click Local Area Connection
3. In the LAN Area Connection Status window, click Properties.

COMPACT ROUTER ADSL
A02-RA110 Pag. 12
4. Select Internet Protocol (TCP/IP) and click Properties.
5. Select the Obtain an IP address automatically and the Obtain DNS server
address automatically radio buttons
6. Click “OK” to finish the configuration.