Atlas Copco 4220 4522 82 Instruction sheet

Operator handle
Printed Matter No. 9836 7130 00 Electric pistol grip nutrunner
Valid from Serial No. A5380001
2013-02-01 Product Instructions
Operator handle 4220 4522 82
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and in-
structions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference

2© Atlas Copco Industrial Technique AB - 9836713000
Table of Contents
EN Product Instructions.......................................................................... 3

Operator handle EN Instruction supplement
© Atlas Copco Industrial Technique AB - 9836 713000 00 3
Instruction supplement
Installing the operator handle
Make sure the tool is disconnected from the cable before dismantling.
Required tools:
• Screwdriver
• Allen key
This instruction describes installation of an operator handle with cable.
Only perform step 3 if installing an operator handle without cable.
1. Remove the protective cover by hand.
2. Unscrew the screws from the lid on top of the tool using a screwdriver and
remove the lid.
3. Put the new handle in position as shown in the picture. Tighten the screws
slightly using an allen key.
a) Tighten the handle with the shorter screws when you have a tool without
a fan.
b) Tighten the handle with the longer screws and the washers when you
have a tool with a fan.
4. Lead the cable on the left side of the tool when the tool front points against
you. Connect the cable to the bus port on the circuit board on top of the
tool.
5. Put the lid with a slot in position.
Make sure the cable is placed in the slot before you tighten the screws.
Tighten the lid with screws.
6. Loosen the screws slightly in front of the tringular holder and remove the
plug on the opposite side of the handle.
7. Pull the cable carefully from the inside of the plug hole until it is stretched.
8. Insert the cable into the hole and put the plug back in position. Tighten the
screws in front of the tringular holder.
9. Put the protective cover back in position.
Loosen the screw in front of the tringular holder and adjust the handle
to optional position. Tighten the screw at recommended torque.

Instruction supplement EN Operator handle
4© Atlas Copco Industrial Technique AB - 9836 713000 00
Configuring the operator handle

Operator handle EN Instruction supplement
© Atlas Copco Industrial Technique AB - 9836 713000 00 5
This instruction describes configuration of an operator handle with the
Power Focus controller. Perform the steps after installing the operator han-
dle.
1. Connect the tool and the Power Focus controller.
2. Switch on the controller.
3. Press PROG to start the configuration.
4. Select Tool and press ENTER to confirm the selection.
5. Select Configuration and press ENTER to confirm the selection.
6. Select Start and press ENTER to confirm the selection.
7. Select Tool start select source and press ENTER to confirm the selection.
8. Select Safety trigger and press ENTER to confirm the selection.
9. As a result Safety trigger appears instead of Tool trigger in the right up-
per corner.
10. Press Store to store all selected values in memory. The safety trigger is
now activated on the tool.
For more information of the Power Focus controller, see the applicable user
guide.

Instruction supplement EN Operator handle
6© Atlas Copco Industrial Technique AB - 9836 713000 00

Operator handle EN Instruction supplement
© Atlas Copco Industrial Technique AB - 9836 713000 00 7

Original Product Information
Atlas Copco Industrial
Technique AB
SE-10523 STOCKHOLM
Sweden
Telephone: [phone]
Telefax: [phone]
www.atlascopco.com
©Copyright 2012, Atlas Copco Industrial Technique AB. All rights reserved. Any
unauthorized use or copying of the contents or part thereof is prohibited. This
applies in particular to trademarks, model denominations, part numbers and
drawings. Use only authorized parts. Any damage or malfunction caused by the
use of unauthorized parts is not covered by Warranty or Product Liability.
Out of respect to wildlife and nature, our technical literature is printed on
environmentally friendly paper.