Attop X-PACK 18 User manual

1
2 3
Drone X1 Backup Propellers X4
Screw driver X1Battery X2
Remote X1
USB cable X1
1
2
1
2
(1) Open Up all 4 blades for the drone
1
2
1. Package Contents
2.Charging
4. Remote Controller
3.Install
(Suitable for wide indoor environments operation and
wind power less than Force 2 outdoor environments)
CHA
(2) Battery Installing
Insert the battery into specified
position.
Insert 3xAAA battery into specified
position.
Remote Controller:
To disassembly, press the battery
buckle button, and pull back to take
it out.
(3) Mobile Device Holder Using
Pull up the position of controller.
Adjust the Mobile Device Holder up and
place the moblie onto the holder.
This aircraft is folding structure, please do open up all four propellers before taking off.
1
1. Speed switch
2. Left stick (Altitude Control / Turn L/R)
3. Power switch
4. One key take off
5. Circle fly
6. One key landing
7. One key return
8. Headless function
9. Right stick (Movement control)
10. Gyro calibration
11. Forward trimming
12. Right trimming
13. Backward trimming
14. Left trimming
15. Filming
16. Take Photo
13
31
2
2
5V
1
2
14
29
10
11
12
3
4
5
6
7
16
13
15
8
┐╠╚ 25.400
AAA 1.5V
AAA 1.5V
AAA 1.5V
battery
case
X-PACK 18 Operation Manual
Suitable for 14 years old and above
Customer Service Email : [e-mail]
www.attoptoys.com
Charging Guide for battery
1. Connect the USB cable with power supply, the USB LED solid on, indicate the
USB cable is power on.
2. Connect the battery with USB cable. If the USB LED solid on, the charging is
completed. Otherwise, it means charging. Please use the drone when fully charged.
Note：Use an power supply with standard output voltage 5V and current greater than or
equal to 2A, otherwise there is a risk of overloading the USB cable and Battery.
The flight time is about 9-10 minutes and the charging time is about 120 minutes.
Low battery warning
When the drone is flying, the indicator lights on the drone are flashing, and the remote
control handle emits a "beep" alarm sound, indicating that the drone power is too low.
At this time, the drone needs to return and charge.
Get 24/7 assistance at
Use camera or QR scanner to scan
Or Visit: https://attop.afterservice.vip

4 5
6 7
12
2
7. Aircraft Functions
5. How To Fly
6.Using the Remote Controller
Left Stick Right Stick
Ascend / Descend Forward / Backward
Turn left / Turn Right Left-side Fly / Right-side Fly
(1) Switch On the Power
First power on the drone
(Keep pressing for 2-sec
and place it on a flat ground
or surface.)
Power on the Remote
(3) Gyroscope calibration
(4) Activate motors for taking-off
Press the Calibration button for the gyro calibration.
(For the aircraft fly more stable if operate this step
before activate motors everytime).
1
1
(2) Frequency pairing
2
2
After activated the motors, press “One key take off” (or push up the Left stick directly)
to fly. Press “One key landing” (or keep pushing down the Left stick directly) to land.
Emergency Stop
In case of emergency status, push the
Left stick to the right corner, meanwhile
push the Right stick to the left corner at
the same time, the drone will immediately
stop and drop off.
Push the Left stick to the lowest left corner, and meanwhile push the right stick to the
lowest right corner, (Or just push the left stick to the top) then the motors of the drone
start rotating.
OR
After powered on the drone, both indicator lights on
the drone and controller are flashing. Push the Left
stick to the top, and then down to the lowest, after
2 secs, the indicators will go steady, that means the
frequency paired successfully.
OR
(5) Take off / Landing
360° Flip Function
TRIMMING ON THE FLYING ACTIONS
1. Short press the Right Stick
2. Push the stick to right, the drone will rotate 360° toward right direction
1. Short press the Right Stick
2. Push the stick to top, the drone will rotate 360° toward front direction.
1. Short press the Right Stick
2. Push the stick to left, the drone will rotate 360° toward left direction.
1. Short press the Right Stick
2. Push the stick to bottom, the drone will rotate 360° toward back direction.
Adjustment for deviated flying to
Front/Backward
If it leans forward, press the down trimmer.
If it leans backward, press the up trimmer.
Adjustment for deviated flying to sideward
If it leans left, press the right trimmer.
If it leans right, press the left trimmer.
trimmer
(forward/backward)
trimmer
(sideward fly)
360°
flip
360°
flip
1
1
1
2
2

8 9
10 11
Front
Back
Origin Headless ModeHeadless Mode
Front
Back
Front
Back
(13) Filming
(14) Take Photo
Speed Adjustment
Take photo / Filming
Users are recommended to stay same orientation as the drone head is facing when the
drone takes off.
Under Headless Mode, the forward direction is the direction that the head of drone faces
when the drone takes off.
In order to make sure the users can tell drone’s direction, we suggest that users better to
stay in the same orientation as the drone facing when it takes off.
Then no matter which direction the head is facing, the drone will lock the controlled
direction as the remote controller, easy to control back the drone.
Press the Headless function button, when the indicator lights slowly flashing,
means it is in Headless Mode.
Press the Headless function button again, when the indicator lights stop flashing,
means deactivate Headless Mode.
Speed ± The drone is set to low speed by default.
Press the Speed button to change the speed gear while flying.
There is 3 gears, each gear has a “beep” notice voice, the
default speed is the most slowly one, when press one time you
will hear "beep beep", then go into the second speed gear, and
press again with "beep beep beep" to the final fastest speed.
Remark: Beginners would be suggested to use
the default speed firstly to play until skillful.
8.Headless Mode Function
9.One key return
Length of main wing: 152mm
Aircraft: 190X226X73mm
Total weight: 148g±2g
Battery: 3.7V 1100mAh
Charging time: About 120 mins
Flight time: 9-10 mins
Gyroscope: built-in
Working temperature: -10°C to 40°C
Remoter controller: 2.4G
Motor: 85X20 4pcs
TF card support: NO
Camera Lens: 1080P
Wifi Transmission Range : 60-80 meters
Working frequency: 2.4G
Battery: 3xAAA
(in a wide open area with no electromagnetic interference)
Camera Parameters
Remote Controller Parameters
10.Aircraft Parameters
Press Take photo button. Please make sure to open the app on your smart phone
before using it, then you can review the photos taken in the media file of app or in
your mobile image file.
Press the Filming button to start and press again to finish and save the video.
Please make sure to open the app on your smart phone before using it, then you can
review the videos taken in the media file of app or in your mobile image file.
Note : The Video and Take Photos switch only for WiFi version.
One Key Return
The remote toward the tail of drone and press the button, then the drone
will fly toward its back following a path parallel to remote direction. The LEDs
on the drone keep flashing when the drone is returning.
Press the button again or move the Right Control Stick, forward to cancel
this function, or the drone will keep flying back.
Note: Please deactivate Headless function and make sure the remote
toward the tail of drone before activate the Return function .

12.Battery Using Attention
12 13
14 15
The aircraft is mostly made of PA fiber or
polyethylene as well as other main materials for
electronic products. Therefore, it must be kept
from the source of heat and exposure to sunlight
so as to avoid possible damage of deformation or
even meltdown due to high temperatures.
This product is suitable for users over 14 years
old. Since the remote-control quadcopter may pose
a certain degree of difficulty for learners at the
beginning, it is recommended for it to be operated
under the guidance of experienced people for the
sake of safe flight.
Safe usage
of the battery
Keep away from
source of heat
Never operate the
product alone
CAUTION
WARNING
FORBIDDEN
Batteries are to be inserted with the correct
polarity. The supply terminals are not to be
short-circuited. Different types of batteries or new
and used batteries are not to be mixed.
The exhausted batteries are to be removed from
the toy. For long time storage, please take them
out to prevent battery leakage.Please dispose
abandoned batteries in accordance to the laws and
regulations of the corresponding region to prevent
pollution to the environment.
Remote-control models of quadcopter are dangerous merchandise. Their flight must be
operated away from the crowd. Such factors as man-made improper assembly or mechanical
damage, poor control of the electronic equipment, as well as the unfamiliar manipulation may
lead to unexpected flight accidents, such as uncontrolled flight and aircraft damage. Users are
advised to pay attention to the flight safety and understand that they are held responsible for
any accident caused by negligence.
CAUTION
Special drone for Indoor and
outdoor should stay away from
barriers
This product is a remote-control drone, that suitable for in indoor using and
outdoor environments (the outdoor wind power less than Force 2). To fly this
drone, please choose appropriate obstacle-free indoor and outdoor sites
with proper distance kept from the crowd or pet animals. Please don’t
operate the product in any unsafe environments, such as places of heat,
wires, power supply, etc., so as to prevent the quadcopter from the risks of
fire and electric shock resulting from collision, ditching, and entangling of
the drone.
FORBIDDEN
FORBIDDEN
FORBIDDEN
FORBIDDEN
Safe usage of the lithium battery
Away from moist environments
Never misuse the product
The interior of the aircraft is also composed of many sophisticated electronic
components so it must absolutely be kept away from moisture or water vapor.
Don’t operate the aircraft in the bathroom or on rainy days; otherwise water
vapor may get inside of the aircraft and cause mechanical parts and
electronic components to malfunction leading to expected accidents.
Please do not disassemble or modify the product. For any upgrade, repair
or maintenance, please use the parts specified in our catalog to ensure the
safety of the structure. Please make sure the product is used within the
limits of operation. Don’t overload the product, and don’t use it in any other
illegal ways than prescribed by safety concerns and laws.
Lithium batteries are more dangerous than others. Be sure to read carefully
and follow the following precautions before using it. We will not be held
responsible for any damages caused by any improper use of the battery.
To avoid the danger of explosion or fires, it is forbidden to use other
chargers than the one made by our factory. Such actions done to the
battery as impact, dismantling, reverse connection of the positive and
negative poles, and burning are forbidden. Avoid metal objects from
contacting the positive and negative poles of the battery, which may cause
short circuit. Please prevent sharp items from piercing the battery, and
avoid the risk of battery fire. Please be careful when charging the battery.
Make sure that the battery is charging within your sight. Keep it out of the
reach of young children so as to avoid dangers. Don’t charge the battery
when the battery is heated after use. Otherwise, it may cause the battery to
expand, change, explode or even catch fire, threatening the safety of life
and property. To dispose of the battery, please recycle the battery in strict
compliance with the waste disposal laws and regulations of local countries
or regions in order not to pollute the environment.
SAFETY AND PRECAUSTIONS
11. FAQ
Matters needing attention
（1）Rechargeable batteries are to be removed from the toy before being charged.
（2）Non-rechargeable batteries are not to be recharged.
（3）Rechargeable batteries are only to be charged under adult supervision.
（4）Only used to charging 2S Li-ion or Li-polymer battery pack. if not, the charger or battery may
be damaged .
（5）During charging, the charger should be put in dry and ventilated place and far away from
heat source and inflammable and explosive substance.
（6）Never immediately charge your battery pack as soon as the flight is finished, or when
its temperature doesn’t cool down. Otherwise the battery will take a risk in swelling, even a fire.
（7）Ensure the correctness of polarity before connection the battery to charger.
（8）Avoid drop and violence during the process of charging. drop and violence will result in
internal short circuit of the battery.
（9）For the sake of safety, please use original charging equipment and battery pack .
please change new one in time when the flying time is becoming shorten due to long time usage .
（10）If it is retained in the charger for a long time after saturated, the battery may automatically
discharge. When the charger detects that the voltage of individual cells is lower than the
rated voltage, it will re-charge until saturated. Frequently charging and discharging will
shorten the lifetime of your battery pack. It is advised that please cut off the power and took
off the battery after the charging is saturated.
Maintenance of battery pack
（1）The battery pack should be put in dry and ventilated place. The storage temperature of
environment is ranged from 18°C to 25°C.
（2）Please avoid frequent charging and excessive discharging the battery pack in order to
prolong its life cycle.
（3）It is a must to maintain the battery pack before long-term storage. That is to charge the
battery to the level of 50-60% saturation.
（4）If the storage term is over 1 month, it is advised to monthly check the voltage of every cell
of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please
refer to the above article （3）.
（5）From the view point of protection, new battery pack should be motivated before usage.
That is to charge and discharge 3-5 times, but discharge is not less than the level of 70%
saturation. This process will make the battery lifetime longer and voltage more stable.
ISSUES CAUSE SUGGESTIONS
1
2
3
4
After the battery is
insertedin the drone,
indicator lights on
drone keep flashing,
no response to
operations
No response after
battery is inserted in
the drone
Motor does not run
when operating the
throttle stick and the
indicator lights on
drone keep flashing
Main motor blades
spin but the drone
won’t fly
1. Some of the blades
have been deformed
2. Battery power is
not enough
1. Replace the main
blade
2. Charge the battery or
replace it with a fully
charged battery
Power for the Li-Poly
battery is not enough
Charge the battery or
replace it with a
full-charged battery
1.Check if the power
for remote and drone
is full charged.
2.Connection of the
poles are not good
1.Open the remote
battery case and make
sure if the battery is
inserted in right position
2. Use a fully charged
battery
3. Reinstall the battery
and confirm whether it is
good connecting with the
poles well.
Frequency matching
between remote and
receiver not successful
Reoperate the frequency
matching for remote
and drone (please refer
to P.4 for details)
13.Disclaimer
Please read this manual carefully before using our product.
This product is not recommended for people under the age of 14. By using this product,
you hereby agree to this disclaimer and signify that you have read it fully. You agree
that you are responsible for your own conduct and any damage caused while using
this product, and its consequences. You agree to use this product only for purposes
that are proper and in accordance with local regulations, terms and all applicable
polices and guidelines ATTOP may make available.

16 17
1918
Description of ATTOP GO drone WIFI Version
How to connect the WIFI Signal
This version of drone comes with the WIFI Live Stream Camera.
1, Download the app “ATTOP CLUB ” from App Store / Google Play.
2, Power on the drone.
3, Go to the WIFI setting on phone/device, choose the WIFI signal
of the drone (X-PACK 18+No.) , and connect it.
4, Now open the app of the drone, and Slip to Select The Drone
“X-PACK 18” then enjoy to play it.
SCAN,AND DOWNLOAD APP
Attention: When the drone is at the statue of low battery, it might
unable to be connected successfully.
pic 1
1Enter to the Interface of this drone after selection.
2Media Folder : After taking photos and videos, you can review
them from this folder.
After connecting the WIFI signal between the drone and mobile
device, and open the APP, we can Slip to Select The Drone
“X-PACK 18” see the screen as image above.
Ready to fly
After connecting the WIFI signal and enter into the operation
interface, press the “”ON/OFF button” to open the sticks.
Wait for 2 seconds till the lights of the drone stop flashing
then press the “Calibration button” to calibrate the drone if first
time play.
Push the Left Control Stick to the top and then release. Now the
rotors of the drone start rotating, that activate the motors.
(see pic 1)
Press the “One Key Take Off ” to fly up the drone (or push up the
Left Contol Stick slowly), to take off. Press the “One Key Landing”
(or keep pushing down the Left Control Stick directly) to land the
drone.
2
1
3
4
Ascend / Descend / Turn left / Turn right
Go forward / Go backward / Left side flying / Right side flying
Gesture control
Music
Speed mode: 30%,60%,100%
360° flip
Headless mode
Gravity Control (press it to perform this function, by changing
your action of shaking device to control the drone flying)
Flight path mode
Voice control
VR mode
Return home page
On/Off for control interface
Switch to take video
Switch to take photo
Go Forward / Backward trimmer
Left / Right side flying trimmer
EMERGENCY STOP !!!
One key take off
One key landing
Calibration
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
1
2
12
3 4 5 6 7 8 9 10 11 12
13
14
15
16
17
18
19
20
21
Step 1
Step 2
Step 3
Step 4

20 21
2, Control with the remote controller
(IF your drone with controller)
1, Power on the drone and power on the remote, after pairing the
frequency between the remote and drone (the lights of the drone
and controller become permanent), then connect the WIFI signal
between your device and the drone.
2, Put the device to the clamp of the remote controller, then go to the
app interface to play the FPV flying.
3, Press the “Picture”button on interface or on controller, to take
picture. Press the “Video” button on interface or on controller, to
take video. After taking you can review the files from the media
folder, or from your album file of your device.
APP operation method
Ascend / Descend / Turn left / Turn right
Go forward / Go backward / Left side flying / Right side flying
Gesture control
Music
Speed mode: 30%,60%,100%
360° flip
Headless mode
Gravity Control: Switch “Gavity Sense Mode ”, wave the
mobile phone as image showed below, the drone will move as
same direction movement.
Flight path mode: Press and you can draw a flying route
plan on the screen, the drone will fly according to the route
you designed.
1
2
3
4
5
6
7
8
9
Voice control: Unlock the motors and the rotors of the drone start
rotating, then press and say “Take off ” / “Landing” /
“Forward” / “ Backward” / “Left side” / “Right side” six voice
instructions, the drone will reflect correspondent actions.
10
19
20
21
VR mode: Suitable for VR glasses using.
Return home page
On/Off for control interface
Switch to take video
Switch to take photo
After taking photos and videos, you can review them from
Home page Media Folder or your album file of your mobile device.
Note: The APP needs your access allowance to phone album,
when first activate this function.
Go Forward / Backward trimmer
Left / Right side flying trimmer
EMERGENCY STOP:In case of an emergency, press
the drone will immediately stop functions and drop off.
One key take off
One key landing
Calibration
11
12
13
14
15
16
17
18
1.Turn Right 2.Turn Left 3. Forward 4.Backward
Customer Service Email : [e-mail]
www.attoptoys.com
Name of App：ATTOP CLUB
Apply to IOS \ Android system (Note: Apply to Android 2.3 or above
such as SAMSUNG, SONY, HUAWEI and etc.
But cannot guarantee the phone of other brands with Android system
could operate stably.)
22
30-Day Whole Unit Warranty For Quality-Related Issue
For 30 days after the date of purchase, we take care of all quality-related
issues with a REPLACEMENT.
Reminder : Be sure to operate your drone as directed.
90-Day Accessories Warranty For Any Reason
For 90 days after the date of purchase, we take care of all accessories
quality-related issues with an ACCESSORY REPLACEMENT.
Reminder: Be sure to maintain your drone as directed.
Note: The APP needs your access allowance to use
microphone,when first activate this function.