Attop F16 User manual

Please read this instruction carefully before use,
and keep it properly for reference.
Customer Service Email : [email protected]
www.attoptoys.com
Suitable for 14 years old and above
F16 User Manual
4

1
SPECIFICATIONS
DRONE
Model: F16
Weight: 174g
Max Flight Time: Approx 15 minutes
Max Flight Distance: 300 m
Max Flight altitude: 120 m
Max Flight radius: 5 m
Operating Temperature Range: 50°F to 140°F (10°C to 60°C)
Dimensions: 140 x 90 x 65 mm (Folded)
285 x 275x 65 mm (Unfolded)
CAMERA
Camera frequency: 2.4 GHz
Resolution: 1080P
Lens: FOV 90°
FPV Distance: 300m (outdoor and unobstructed)
Photo: JPEG
Video: MP4
Controllable Range: Pitch: -90° to 0°
CONTROLLER
Operating Frequency: 2.4 GHz
MAX Transmission Distance: 300m (outdoor and unobstructed)
Battery: 3x1.5V AA.
DRONE BATTERY
Capacity: 1800mAh
Voltage: 3.7 V
Battery Type: Li-Po
Energy: 6.66 Wh
Charging Temperature Range: 50°F to 140°F (10°C to 60°C)
Charging Time: 150 mins
BATTERY CHARGER
Input: 5V 2A
Output: 11.4V 1-2A

Remote Contrl Function Description
Note:The remote control automatically adjusts the frequency. Please calibrate the gyroscope and geomagnetism
before starting the flight to ensure the flight stability.Boot default GPS mode. Please turn to Indoor mode manually
when flying indoors, otherwise you can't take off.
2
Short press:Speed switch
Long press:Obstacle
avoidance
Long press:Indoor /
GPS mode switch
Short press: calibrating gyroscope.
Long press: calibrate geomagnetism
Short button: one key return
(effective in GPS mode).
Long press: headless mode
Camera steering angle“+”
Camera angle“-”
One key takeoff / landing
Long press:emergency
stop
Steering rod
Long press:ON
Throttle lever
Remote control power
Drone power
Distance display
Height display
Unlock the Drone motor icon.
(1 for locking, 2 for unlocking)
GPS mode switch
Signal
Number of satellites Photo
Headless mode
High speed Low speed
One key return
Video
Remote control display screen function description

3
(1) Remove the battery from the aircraft.
(2) Connect the battery to the specific charging
cable, and then insert the cable into the
charging equipment such as the USB power
supply.
(3) When the remote control is charged,
the indicator lights up while be off when charging completion.
Put the battery correctly according
to the electrode instructions (+,-) of
the battery box as shown
USB charging cable
Drone battery
3.Installation and startup of aircraft battery
Put the fully charged battery into the battery slot of the aircraft and hold down the
power switch until the aircraft lights up.
Remote Control and Aircraft Battery Installation and Charging Instructions
1.Remote control battery installing
2.Drone battery charging
3
1
2
5V
Note：Use an power supply with standard output voltage 5V and current greater than or
equal to 2A, otherwise there is a risk of overloading the USB cable and Battery.
The flight time is about 15 minutes and the charging time is about 120 minutes.
Aircraft installing
1.Folding

3.Pairing
Turn on the aircraft and place the aircraft on the flat ground. At this time, the aircraft indicator flashes and then
turn on the remote control. And then pairing automatically between drone and remote control. Pairing success
and completed after 2-3 seconds, the remote control handle emits "beeps" sound.
4
Short press:Gyroscope calibration
Remote Control
1.Mobile phone rack
Pull out the mobile phone handle
and clamp the mobile phone.
2.Grip installing
Take the grips under the controller and install
to specified position
4.Gyroscope calibration
The aircraft must calibrate the gyroscope before flight, press the gyroscope
calibration button briefly, and the aircraft indicator flashes into the gyroscope
calibration. After the calibration is completed, After the flash, the calibration is
completed.
Note：1. The GPS mode is default when turn on the drone.
2. Could not be change to indoor mode when the drone searched GPS signal.
Please install the propeller in the correct direction,
and lock the screw after installing the support arm
of the aircraft corresponding to the mark (A/B) on
the propeller.
2. Installation of aircraft blades

5
5.Geomagnetic calibration
After the gyroscope calibration is completed, the next step is geomagnetic calibration, press and keep the
gyroscope / geomagnetic calibration button for 2 seconds, and the tail light of the aircraft flashes into
the geomagnetic calibration. And then, take the aircraft and rotating horizontally 3-5 circles.
After the remote control handle emits a "beep" sound, then rotating the aircraft vertically, the remote control handle
emits a "beep...." sound again, and the calibration is successful.
Long press:Geomagnetic calibration
(Pic 1)
(Pic 2)
(Pic 3)
6.One key takeoff / landing
Long press:emergency stop
Note：1. In GPS mode, one key landing function could be activated when the
drone flight altitude not higher than 10m, the flight distance not longer than 5m.
2. The drone will power off automatically after 8 mins when motors not any
woking.
3. The remote control will power off automatically after 20 mins when not
any action.
Stay away from the
rotating propellers and
motors.
GPS Mode (screen show “GPS ON”):
After searched 12 GPS signals and pushing the Left stick to
the lowest left corner, and meanwhile push the right stick
to the lowest right corner (Pic 1), then the motors of the
drone start rotating. And now press one key take off buttom (Pic 2),
then the drone will be taking off.
Indoor Mode: After frequency pairing between drone and
remote control and then long press the Indoor mode buttom (Pic 3)
to change to Indoor mode (screen show “GPS OFF”).
Next, push the Left stick to the lowest left corner, and meanwhile push
the right stick to the lowest right corner (Pic 1), then the motors of the
drone started rotating. And now press one key take off buttom (Pic 2),
then the drone will take off.
Emergency stop: Long press one key take off buttom (Pic 2) to activate emergency stop when the
drone flight altitude not higher than 2m .
1 2

Controller joystick
Throttle (left joystick)
Rotation (left joystick)
6
When switching to headless mode, the aircraft will give up its front,back,
left and right directions, and take the nose direction
(one side with camera) of the aircraft at 2.4 G frequency pairing
as the forward direction.
(1)Direction definition before take-off: Put the forward direction
of the aircraft directly in front of you (there is a camera side,
and then turn on the remote control for 2.4 G frequency pairing
to complete the headless mode direction definition of this flight.
(2)Press headless mode when flying, and the remote controller keeps
making noise; The aircraft lights quickly flash and enter the headless mode;
Press the headless mode key again, and the emote control handle emits a "beep" sound and exit the
headless mode.
Long press:
Headless mode
Forward and backward (right joystick)
Left and right side flight (right joystick )
Note：1. The headless mode could not be activated when the drone in GPS mode.
2. The headless mode could be activated when the drone in indoor mode.
3. Before activate the headless mode, the drone forward direction must be
determined, that is the direction of the aircraft on the ground after startup.
Headless Mode (Only indoor mode)

7
Obstacle Avoidance Mode (Only for Indoor mode)
Camera pitch control
Through the remote control steering gear control key control camera up
and down shooting angle.
1, press the camera lens electric up button, the body lens angle up slowly
move; release the button that stop moving.
2, press the camera lens electric down button, the body lens angle down
slowly move; release the button to stop moving.
Gear 1 speed is default.
The speed switch is divided in three speeds for the flight of forward, backward and
left & right side. It defaults to gear 1 after power on. And when press the remote
control with two sounds of Beep for the gear 2, three sounds of Beep for the
gear 3 and one sound of Beep for returning to gear 1.
Speed Switch
Long press:Obstacle
avoidance
Short press:Speed
UP Down
Note：1. Gear 1 speed is the only speed when the drone in indoor mode.
2. Beginners would be suggested to use the default speed firstly to play
until you are skillful.
1. The obstacle avoidance function will be activated automatically
when the drone change to indoor mode. Please make sure 3m
space enough around the drone when operating indoor before take off.
2. Activated obstacle avoidance, the aircraft indicator flashes slowly,
the flight speed slows down automatically, the aircraft indicator flashes
and the remote control handle emits a "beep" alarm sound when
close the surrounding obstacles, and hovers in a safe range from the
stop to ensure flight safety.
1.5 meters
1.5 meters
1.5 meters
1.5 meters
Don’t touch the
Gimbal.
Obstacle
Obstacle
Obstacle
Obstacle

8
Short press:
One key return
One key return to home
Return to Home (RTH)
· The Return to Home function brings the drone back to the Home Point.
· The Home Point is the location at which the drone takes off. This location will be recorded
as the Home Point.
Failsafe RTH
If the remote control disconnect with drone when flying, the remote control handle emits a
"beep" alarm sound. The drone will automatically start the return procedure and it will fly
back to the Home Point. You can exit “Failsafe RTH” mode by pressing the “Return to Home”
button or pushing the Throttle Joystick if the controller signal is recovered.
· During the Failsafe Return procedure, the drone cannot avoid
obstacles.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

9
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Low Voltage RTH
①The “ ” symbol is displayed on the controller screen. Then the First Low Voltage
RTH will be triggered. The remote control handle emits a "beep" alarm sound. The drone will
return automatically in the following two conditions: (At this time, the drone can only fly within
a safe range of its height no more than 20m and its distance no more than 20m.)
a. When the flight distance is more than 20m, the
drone will fly automatically into the electronic fence
(H 20m x D 20m) and stay the current distance, then
exit the First Low Voltage RTH. If the flight distance
is equal to 20m, the drone will stay current distance,
then exit the First Low Voltage RTH.
b. When the flight altitude is higher than 20m, the drone
maintains its current height and then flies automatically
into the electronic fence (H 20m x D 20m), then exit the
First Low Voltage RTH. If the flight altitude is lower than
20m, the drone will ascend to 20m and fly automatically
into the electronic fence (H 20m x D 20m), then exit the
First Low Voltage RTH.
②If the drone’s lights begin to flash rapidly the “ ” symbol will be displayed in the
controller screen and the remote control handle emits “beep-beep” alarm sound. The Second
Low Voltage RTH is automatically triggered. Drone will return automatically.
1. During the Second Low Voltage RTH, the drone can not be controlled
to ascend and descend. But you could operate the Right Joystick to
change the landing position.
2. The drone cannot avoid obstacles.
1. During the First Low Voltage RTH, the drone ascends to 40m when the
flight altitude is lower than 40m and flight back then descend altitude to
20m.
2. During the First Low Voltage RTH, if the drone flight altitude is higher
than 40m, the drone will keep in current altitude and flight back then
descend altitude to 20m.
Descend
Forward
H＞20m
Flight Altitude ＞20m
Flight Distance ＞30m
Home Point Range: Radius 1.5m
Home
Point
20m
D＞20m
20m

10
Problem solving guidelines
Problem Cause Treatment mode
After the aircraft is connected
with the battery, the indicator
light flashes continuously,and
the operation is unresponsive
Aircraft and remote controller 2.4 G frequency
alignment was unsuccessful
Please re-perform 2 4G alignment
between aircraft and remote control
There is no reaction after
connecting the battery.
(1) Check whether the remote control or aircraft is
powered on
(2) Check the remote control or aircraft battery
for low voltage
(3) Whether the positive and negative plates of
the battery is in poor contact
(1) Reinstall the battery
(2) Charge or replace new batteries
(3) Confirm that the positive and negative polarities
of the battery are installed correctly
When pushing the throttle
remote lever, the motor
does not rotate, and the
indicator light of the aircraft
flashes all the time
Aircraft battery is low Charge the battery or replace a fully charged battery
The propeller of the aircraft
keeps rotating but cannot
take off
(1) Propeller deformation
(2) Aircraft battery power is insufficient
(1) Replace the spiral prize
(2) Charge the battery or replace a fully charged battery
The aircraft vibrates badly Propeller deformation Change propeller
The aircraft lost its balance
after falling The center point of gyroscope
on aircraft is wrong Re-calibrate horizontally or reboot
Re-alignment
The aircraft always drifts
in one direction
The center point of gyroscope
on aircraft is wrong Re-calibrate horizontally or reboot
Re-alignment
Note: the batteries of newly purchased products are
low voltage, please fill the battery before use!
Disclaimer
Please read this manual carefully before using our product.
This product is not recommended for people under the age of 14. By using this product,
you hereby agree to this disclaimer and signify that you have read it fully. You agree
that you are responsible for your own conduct and any damage caused while using
this product, and its consequences. You agree to use this product only for purposes
that are proper and in accordance with local regulations, terms and all applicable
polices and guidelines ATTOP may make available.

11
WiFi connection instructions
Downloading App
Scan the QR code, corresponding to either App Store™ or Google™ Play Store and
download the “ G07 Drone ” application for free.
Required Operating Systems: iOS v8.0 and later / Android v4.3 and later
Tip: Please use a smartphone that can support receiving 2.4G and 5G WiFi signals.
Connecting to Wi-Fi
①Connect your smart phone to the Wi-Fi network created by the drone. Check the drone’s
status in the “G07 Drone” app.
②Your smartphone will launch a search for the available Wi-Fi hotspot:
③Select the Wi-Fi network: F16-XXXXXX
④Wait for several seconds until your smartphone connects to the drone's Wi -Fi hotspot.
This connection is generally represented by the Wi-Fi logo appearing on your smartphone’s
screen.
⑤ Select the F16 drone and click “Start” to into the interface.
F16-XXXXXX

12
APP OPERATION INSTRUCTION
Operation Interface
Home page
More function Follow me
One key take-off/Landing
Return to Home (RTH)
Live map
Unlock
Waypoints
Point ofinsterest
Flip image
VR mode
Gestures Photo/Video
Music
Fright height
Fright distance
Vertical speed
Horizontal speed
GPS signal
WIFI signal
Drone battery power
Setting
Photo/Video mode
Shutter
Media gallery

13
Follow Me (In GPS mode)
The follow me function could be activated when the distance range is 5m-20m between player
and drone.
1. Click the“ ” icon on the app interface to enter the Follow Me function.
2. To exit Follow Me Mode, simply click the “ ” icon on the app interface again or push right
joystick, the drone stops following then hovering.
3. The Home point could not be changed when cancel follow me function.
1
2
3
4
Waypoint Flight
1. Click the“ ” icon on the app interface to enter the Waypoint flight function.
2. Draw a line on the map to create a path (maximum 20 paths). Click “ ” icon, the drone
will now fly along the path according to the points connected on the map.
3. Click the “ ” icon to deduct all the path.
4. Click the “ ” icon to navigation.
5. Click the “ ” icon to drone location
6. The drone could not fly back to the starting point after executing flight path.
7. If the flight path fails, please delect all of path and try again.
Exit the Waypoint flight mode by clicking the live transmission image .
.Waypoint flight function could not be activated when the drone battery
lower power.
·DO NOT fly the drone towards people, animals, or small/ fine objects
(e.g. tree branches and power lines) or transparent objects (e.g. glass
or water).
·There may be some deviation between the expected and actual flight
path.
.Follow me function could not be activated when the drone battery low
power.
It is recommended to enlarge the map if you want to use Waypoint. flight.

14
Gesture control (In GPS mode / In indoor mode)
Setting
1. Keep away 2m from drone and click the“ ” icon on the app interface to enter the
Gesture function.
2. activate take photo.
3. activate video /cancel video.
Tap to start setting up your drone.
Tap to calibrate the drone.
Tap to check the flight logs.
Tap to check the last recorded location of the drone.
.Point of interst function could not be activated when the drone battery
low power.
R 5m
Point of Interest (In GPS mode)
1. Click the“ ” icon on the app interface to enter the Point of Interest function.
2. The drone will flight around the point of ineresting point (Radius approx 5m) .
3. To exit Point of Interest mode, simply click the “ ” icon on the app interface again
or push right joystick to any direction.

30-Day Whole Unit Warranty For Quality-Related Issue
For 30 days after the date of purchase, we take care of all quality-related
issues with a REPLACEMENT.
Reminder : Be sure to operate your drone as directed.
90-Day Accessories Warranty For Any Reason
For 90 days after the date of purchase, we take care of all accessories
quality-related issues with an ACCESSORY REPLACEMENT.
Reminder: Be sure to maintain your drone as directed.
Guangdong Attop Technology Co., Ltd.
Linghai Industry Zone, Laimei Road, Chenghai District, Shantou,
Guangdong, China.
Website: www.attoptoys.com
Customer Service Email : [email protected]