ATV VD650WDR User manual

INSTRUCTION MANUAL
WDR Super High Resolution
Day & Night Color Camera

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the m
anufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plu
g. A polarized plug has two blades with one wider than the other. A gro
unding type plug has two blades and a third grounding prong. The wid
e blade or the third prong are provided for your safety. If the provided p
lug does not fit into your outlet, consult an electrician for replacement o
f the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from th
e apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use cau
tion when moving the cart/apparatus combination to avoid injury from ti
p-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-su
pply cord or plug is damaged, liquid has been moisture, does not oper
ate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE B
Y QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RIS
K OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OT
HER THAN THAT CONTAINED IN THE OPERATING INSTRUCTION
S UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use Certified/Listed Class 2 power source only.

CONTENTS OF PACKAGE
The package contains the following
Camera in Housing ------------------------------------------------------------------1
Instruction Manual (This Document) --------------------------------------------1
Accessory Kit for Installing ---------------------------------------------------------1
Drilling guide label -------------------------------------------------------------------1
TABLE OF CONTENTS
INTRODUCTION ---------------------------------------------------------------------------------------4
CAMERA CONNECTIONS --------------------------------------------------------------------------5
INSTALLATION-----------------------------------------------------------------------------------------6
LENS ADJUSTMENT ---------------------------------------------------------------------------------8
DC AUTO IRIS LENS ---------------------------------------------------------------------------------8
OPERATING CAMERA-------------------------------------------------------------------------------9
CAMERA ADJUSTMENT ----------------------------------------------------------------------------9
EXTERNAL DIMENSION ----------------------------------------------------------------------------16
SPECIFICATIONS -------------------------------------------------------------------------------------17
3

INTRODUCTION
The camera provided high-quality image using SONY Wide Dynamic 1/3” Super-HADII
PS 960H CCD and digital signal processing LSIs.
Features:
•1/3” Super-HADII PS 960H CCD
•Super high-resolution of 650TV lines
•0.4 lux(Color), 0.04 lux(B/W), 0.001 lux(Low-Shutter) @ F1.4 Sensitivity
•C/CS, back-focus cam for easy adjustment
•Auto Electronic Shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter
modes [1/60(1/50) ~ 1/10,000]
•On Screen Display (OSD)
•Auto and Manual white balance modes
•Support Line-Lock external synchronization
•Digital PTZ
•Digital Effect (H/V reverse, 180 degree rotate, inverse, freeze)
•2D-NR, 3D-NR (DNR Demo)
•Back Light Compensation
•Back Light Masking (MAX. 15 area)
•Excessive High-Light Compensation
•Wide Dynamic Range (~x512)
•Various Detection Method (zone detection, motion trace, face trace, mine area,
absent detection, cross object counting, entrance counting)
•Day & Night(Auto, Manual, External, Filter delay)
•Various Alarm Method (Period, Snooze, Polarity Select)
•Privacy Mask or Mosaic (MAX. 15 area/4-point polygonal/transparency)
•Scene Change Detection
•Sens-Up (~x32)
•White Pixel Remove
•Frame Control (Auto, 1~7 sec)
•System Lock (4-Digit password)
•RS-485 Remote camera control
•Compatible with Video, DC type lenses with OSD select
•Quick connect for Video or DC lens with 4-pin connector
•Operates in 12VDC or 24VAC
•User Certified / Listed Class 2 power source only
4

CAMERA CONNECTIONS
Connection Cable Description
COLOR Description
RED AC24V/DC12V
WHITE AC24V/DC12V
ORANGE ADKEY
BROWN GND
BLUE RS485(-)
GREEN RS485(+)
YELLOW ALARM OUT
GRAY DN EXT-IN
BLACK&WHITE DN EXT-OUT
BLACK GND
SKY BLUE UTP+(optional)
PINK UTP- (optional)
1) External Day/Night Control : To select Day/Night mode using external equipment,
by connecting control lines to the appropriate terminals.
DAY&NIGHT OUTPUT (Black&White)
Is the camera function that can turn on an external IR LED Lamp by detecting
the sensitivity on the AGC level when the D&N mode is set "AUTO" on the
OSD menu of the camera
5
DAY&NIGHT EXTERNAL INPUT (Gray)
Is the camera function that can be switched to DAY Mode or NIGHT mode by
receiving the D&N on/off signal from external light sensor or IR LED LAMP.
This needs the D&N Mode to be set to "External" on the OSD menu of the
camera to work
DAY&NIGHT INPUT
Gray
GND
Black Close contact: NIGHT
Open contact: DAY
●
●
GNDBlack
DAY&NIG
Black&White ●5V/10mA : IR LED ON (NIGHT)
●0V : IR LED OFF (DAY)
2) Alarm Out
Motion detection signals are output through this port. (YELLOW AND GND)
Active state is configurable.
3) Power Input Terminal
RED & WHITE : DC Power is recommended to use the DC power supply that can
support inrush current over 0.75A
4) Camera Control
GREEN : RS 485+
BLUE : RS 485-

5) UTP (optional)
Video signal through out the UTP Cable (SKY BLUE(+) & PINK(-) )
6) External AD Key Control (optional)
INSTALLATION
45mm
3mm
Black/GND
White/AD output
GND Terminal/Brown
AD Key Terminal/Orange
Remote Control (optional)
1m 95mm
1. Loosen the four torx screws located midway up the front of the housing leave the
screws intact in the front portion. (Fig. 1)
2. Drill the mounting location, using the bottom of the housing as a Drilling guide label.
(Fig. 2)
3. Attach the housing to the ceiling using suitable fasteners, M6x35 tapping screws are
supplied only use if they are suitable. (Fig. 2)
4. Closing the housing using the loosen torx screws. (Fig. 3)
Torx screws
M5x10 (4x)
Torx screws
M5x10 (4x)
Seal around
the housing
Figure 1 Figure 2 base tightly
i
6

Mounting Screw
M6X35(4x) Plastic Anchor(4x)
Ceiling
Drilling
Guide Label
Rubber Washers(4x)
Figure 3
MOUNTING HOUSING TO
AN ELECTRICAL BACK BOX
The housing can also
be mounted on a 4s or 2s
electrical box.
Electrical box
Torx screws
UNC 8-32 x 0.75
7

LENS ADJUSTMENT
Field of view: Adjust setting
from Telephoto (T) to wide (W)
field of View.
Focus: Adjust lens focus from
near (N) to infinity.
DC AUTO IRIS LENS
2.6-6mm 4-9mm 2.8~12mm 6-50mm
Image Size 1/3” CCD 1/3" CCD 1/3" CCD 1/3" CCD
Focal Length 2.6-6.0mm 5% 4.0-9.0mm 5% 2.8-12mm 5% 6.0-50mm 5%
Aperture
Ratio 1 : 1.6 5% 1 : 1.6 5% 1 : 1.4 5% 1 : 1.6 6.9%
Angular
Field of View
(Degree)
DIAGONAL
2.6mm : 134.6
6mm : 59.2
DIAGONAL
4mm : 92.4
9mm : 39.2
2.8mm : 119.9
12mm : 28.8
DIAGONAL
6mm : 58.6
50mm : 7.1
8

OPERATING CAMERA
① Enter Button
② Up Button
③ Down Button
④ Left Button
⑤ Right Button
⑥ Spot Video Output
⑦ UTP(Optional)
CAMERA ADJUSTMENT
<White Balance>
1) Auto(Auto White Balance) : AWB mode (1800ºK ~10500ºK)
2) Push/Hold : Push&Hold Mode.
To find the Optimal setting for the current luminance environment in this mode,
set the direction towards a sheet of white paper and select Hold and press enter
button. If the environment changes, readjust it.
3) CRS Mode(Color Rolling Suppression) : Decrease color rolling effect.
This operation take some time about 10 seconds and user can stop this
operation by pressing enter button.
When CRS Mode is on, color tone can be weak.
4) Indoor : Set color temperature to indoor (3200ºK)
5) Outdoor : Set color temperature to outdoor (6300ºK)
6) FL(Fluorescent Light) : Set color temperature to fluorescent light fixed gain.
7) User(User Set White Balance) : Adjust red or blue gain.
R(R-GAIN):Adjust R-GAIN value (0-255)
B(B-GAIN):Adjust B-GAIN value (0-255)
<Auto Exposure>
1) SHT(s)(Electronic Shutter) : Select Shutter mode.
Auto(1/60(1/50) ~ 1/100,000 Auto run, Manual 8 step from 1/60(1/50) ~1/10,000).
2) FLC(Flicker-less) : Flicker-less On/Off.
3) AGC(Auto Gain Control) : AGC Gain(Off, Low, Middle, High)
4) Sens-Up(Slow Shutter) : Maximum Low-Shutter select. (x2-x32 and Off)
5) Offset Add : Force the picture to turn up at low luminance environment.
<BLC/WDR>
1) Normal AE : BLC/WDR function off.
2) WDR(Wide Dynamic Range) : Wide dynamic range mode on.
3) EHLC(Excessive High Light Compensation) : EHLC mode on.
9

10
excessive lighting compensation is performed when the weighting on the
high-brightness side is increased.
4) Auto(Auto Weighting BLC) : Auto weighting BLC on.
5) Spot(User Setting BLC area) : Spot metering mode on.
Posi : OSD mode to adjust the position of the spot metering area.
Size : OSD mode to adjust the size of the spot metering area.
6) Zone(Preset BLC area) : Fixed metering area mode. (1-9).
<Mask>
1) Mask: Select mask area(1-15).
2) Func: Select mask function.(Privacy, BLM, Both, Off).
Privacy : Area to screen on the display.
BLM : Back Light Mask.
Selected BL Mask area that will be except of the auto exposure
If there is a high light installed in a limited environment such as an
apartment parking garage or gas station entrance, removing the high light
makes it possible to view car license plates efficiently.
Both : Privacy function and BLM function on.
Off : Function off.
3) Edit : Mask area edit.
Edit mode take effect during Func not Off.
Size : adjust the size of the Privacy and BLM mask area.
Posi : adjust the position of the Privacy and BLM mask area.
Tilt : adjust tilting of Privacy and BLM mask area.
Color: Select Privacy and BLM mask (0-14).
Transparency: Select Privacy mask transparency (Default 3/0-3).
Mosaic: Select Privacy and BLM mask mosaic On/Off
Adj. Mosaic: Adjust Privacy and BLM mask mosaic level (0-31).
<Detection>
Func : Detection function selection.
Sens Down : Adjust to Motion Sensitivity using left/right Buttons.
1) OFF : Detection function off.
2) Zone : Area motion detection mode.
Zone : Select Motion detection zone (Zone1-4).
Func : Select Motion detection on/off.
Size : Press Enter button to adjust the size of the Motion detection area.
Posi : Press Enter button to adjust the position of the Motion detection area.
Link Zoom : Select Motion detection with D-PTZ function that On/Off .
When the motion triggered in the area, move to the area with D-PTZ.
3) Motion Trace : Motion trace mode on.
Tracks an object through a scene and generates an alarm.
4) Face Trace : Face Trace mode on.
Tracks face through a scene and generates an alarm.
Sens Down : lower value is more widen the scope to judge face. (0~127)
Min Size : Minimum face size configuration (0 : minimum face size is to none)

11
The result of face trace can be inaccuracy.
5) Mine : Mine area mode.
By this function, User can draw motion detection area with free dotting
Set Mine : Press the Enter button to Set Mine mode.
< > : Move : Mine Zone move using the Left and Right buttons.
UP:Set : Mine Zone setting using the Up button.
DN:Clr : Mine Zone clear using the Down buttons.
ENT:End : Press the Enter button to set Mine mode end.
Clr All : Press the Enter button to set Mine area clear.
Display : Select Mine Display On/Off.
6) Absent : Press the Enter button to Absent detection mode.
Absent : Detect object appeared or removed the scene.
Sens Down : Adjust sensitivity of Absent check(0-255).
In low luminance environment, the accuracy is down of the result.
Because object color is effect to auto exposure, the accuracy is down of the result
If the object is too big, the accuracy is down of the result.
7) Cross : Cross counting mode.
Zone : Select Cross Zone using the Left and Right buttons (Zone 1, Zone 2).
Size : Adjust the size of the Cross zone.
Posi : Adjust the position of the Cross zone.
Direction : Select Cross Direction.
Alarm Cnt : Set alarm out cross count. Alarm count number is delaying number
before output alarm.
Reset Cnt : Cross count reset.
If object is passing so fast through the two area, counting is not operating. In this case,
adjust to expand space between two area or decrease size of area.
If passing object is too long, counting result can be inaccuracy. In this case, adjust to
expand space between two area or adjust to decrease size of area.
If two object passing the area in the same time, the results can be inaccuracy.

8) Entrance : Entrance counting mode. The object move in through the entrance,
counting number increases.
Size : Press Enter button adjust the size of the Entrance zone.
Posi : Press Enter button adjust the Position of the Entrance zone.
Alarm Cnt : Set alarm out entrance count. Alarm count number is delaying
number before output alarm.
Reset Cnt : Entrance count reset.
Crossing object is not considered. / Several objects will not be detected.
If the distance is increases between the camera and entrance, the result can be
inaccuracy.
Several Object
Crossing Object
Camera Installed at the ceiling
Crossing object is none
One object is passing.
The distance is too long
<Picture/DNR>
1) Sharpness : Adjust sharpness of outlines (0~15)
2) Resolution : Select high resolution mode (Low/Mid/High)
3) 2D-NR : Select 2D noise reduction level (0~6)
2D-NR : Noise reduction on a frame
4) 3D-NR : Select 3D noise reduction level (0~31)
3D-NR : Noise reduction through the several frame
5) DNR Demo : Select DNR Demo Display On/Off using the Left and Right Buttons
None DNR Effect
Display DNR Applied Display
<Effect/Special>
1) d-Effect(Digital Effect) : Select digital Flip/Rotate state (Off/Rotation/Mirror/V Flip )
2) Nega : Select negative color state(on/off)
3) d-PTZ (Digital Pan, Tilt, Zoom) : Adjust d-PTZ.
Func : Press the Enter button to turn digital zoom on/off.
Zoom : Use the Left and Right buttons adjust to digital zoom(0-255).
12
Pan&Tilt : Press the Enter button to access the Pan&Tilt.
Use the Left and Right buttons adjust to digital pan

13
Enter button to reset digital pan and tilt.
h rate for output video. This function is useful to
e to ON/OFF, and Auto. video is being refresh
gured interval.
een two frame.
When object start moving, The output video possible to cut a little time.
Use the Up and Down buttons adjust to digital tilt
Press the Enter button to exit.
PT Reset(Pan & Tilt Reset) : Press the
4) Freeze : Select the still mode on/off
5) Frame Control: Select term of refres
reduce the recording to data storage.
Func : Select frame control mod
Auto mode : When motion is not detected, output
in configured interval. And when the motion is detected, output video is
switched to real time video.
ON : Always refresh in confi
OFF : Always real time video.
Renewal(sec) : Select an interval betw
6) ScnChg/Unfoc : Select scene change/unfocus detection On/Off . reaking or …)
In low luminance environment, the accuracy is down of the result.
Inform that whether scene have been changed or not. Detect b
changing in the watching scene (Spray, Screen Camera, Changing Scene
This function is linked with alarm out
In very low luminance environment, operation is not be performed.
It is not be performed when moving object is exist.
<System Setup>
1) Cam Info : Camera ba
sic information display CCD Type/Lens Type
: Configuration Lock. ock”, User must to input 4-character
Default password is “0000”.
Cam ID/Baud rate/Protocol/Firmware Ver./
2) General Setup
System Lock
When system lock is set to “L
password to enter OSD menu.
Change PID : Change the administrator’s password o input the character. m.
Move cursor with OSD Key and Press Enter t
Comm(RS 485 Communication) : Press the Enter button to access the Com
Cam ID : Select the camera ID (001 - 255).

14
A. Title character
tle ing
ed (2400/4800/9600/19200).
Title : Edit camera title.
Display : Display item select. splay On/Off.
Perio in/5min/Cont.)
l Setup Menu. ult)
: DC, Video, Manual Lens selected Iris : adjust AE Speed
ss the Enter button to
st AE base reference level. DR Ref. rence Level. e.
ed (2400/4800/9600/19200).
Title : Edit camera title.
Display : Display item select. splay On/Off.
Perio in/5min/Cont.)
l Setup Menu. ult)
: DC, Video, Manual Lens selected Iris : adjust AE Speed
ss the Enter button to
st AE base reference level. DR Ref. rence Level. e.
Baud Rate : Select serial communication speBaud Rate : Select serial communication spe
Protocol : RS-485 protocol. (COMMAND/FASTRAX/PELCO-D/Pelco-D)Protocol : RS-485 protocol. (COMMAND/FASTRAX/PELCO-D/Pelco-D)
Title Site_0
B. Delete
C. Character table
D. Command line
- Clear : Clear Ti
- Cancel: Cancel edit
- Accept: Save TitleSave Title
Cam ID : Camera ID diCam ID : Camera ID di
Title : Title display On/Off.Title : Title display On/Off.
Alarm .Alarm .
d : Alarm out period (5sec/10sec/20sec/30sec/1md : Alarm out period (5sec/10sec/20sec/30sec/1m
Snooze : Alarm out snooze(Off/5sec/10sec/20sec/30sec/1min/5min)Snooze : Alarm out snooze(Off/5sec/10sec/20sec/30sec/1min/5min)
Active pol : Alarm output active state configuration. (Low, High)Active pol : Alarm output active state configuration. (Low, High)
System InitSystem Init
Cancel : Back to GeneraCancel : Back to Genera
Confirm : Initialize all data. (Factory DefaConfirm : Initialize all data. (Factory Defa
3) Lens3) Lens
IrisIris
DC lens and video lens can adjust AE SpeedDC lens and video lens can adjust AE Speed
Normal AE Ref (Auto Exposure Reference Level) : PreNormal AE Ref (Auto Exposure Reference Level) : Pre
access the AE Ref.
Ref Lvl : Adju
access the AE Ref.
Ref Lvl : Adju
WDR Ref : Press the Enter button to access the WWDR Ref : Press the Enter button to access the W
Ref Lvl : Adjust the WDR long-time control Base RefeRef Lvl : Adjust the WDR long-time control Base Refe
4) LLC(Line Lock Control) : Press the Enter button to access the Line Lock mod4) LLC(Line Lock Control) : Press the Enter button to access the Line Lock mod
Func : Select Line Lock function On/Off using the Left and Right buttons.Func : Select Line Lock function On/Off using the Left and Right buttons.
Phase : Adjust Line Lock sync phase using the Left and Right buttons. (0~100)Phase : Adjust Line Lock sync phase using the Left and Right buttons. (0~100)
☞< > ENT:Del
lear Cancel Accept
ABCDEFGHIJKLM
C
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-. 0123456789
A
B
C
D

15
Activate only AC power inputted.
5) White Pixel
Det Exe : Press Enter button to turn White Pixel Compensation mode Start.
ENT to Adj : Press Enter button to start White Pixel Compensation start.
Proc : Process to find white pixel.
Done : Process ended
Det Count : Result of white pixel detection.
Func : Select erasing white pixel function On/Off using the Left and Right buttons.
Det Level : Select the judgment level of white pixel using the Left and Right
buttons (1~16)
Det View : Select display of detected white pixel.
6) Day/Night
Mode : Select D&N mode.
Auto : Filter operates automatically according to brightness.
Day : The camera outputs the video image only in color.
Night : The camera outputs the video image only in black and white.
Ext : This menu automatically converts the COLOR Mode into the B/W
Mode or vice versa depending on illumination with an external sensor.
Night Mode : Select B/W Burst On/Off
Delay(s) : Adjust the working time of the filter when D&N mode is Auto (1-60 sec).
D>N Level : Select switching level Day to Night when D&N mode is Auto (0-15).
N>D Level : Select switching level Night to Color when D&N mode is Auto (0-15).
<Bottom Line Menus>
When user entered in main menu and sub-menus, following menus will be appeared.
I. Main Manu (menu in bottom lines)
A. Exit : Save & Exit.
B. Load : Load Default Value.
II. Sub Menu (menu in bottom lines)
A. Return : Return to previous menu.
B. Exit : Save & Exit
1) Exit Menu
Save&Exit : Current environment values save.
Exit : Disappear menu osd.
2) Load Default Setup
Yes : Load default to current configuration. and return to previous menu.
No : No operation, and return to previous menu.

EXTERNAL DIMENSION
Window Size
0.1 in. (2.5mm thick),
impact-resistant P.C (LEXAN)
3.93 in. (10cm) diameter
Cable Entry One 1" opening holes
Weight / Shipping 1.54 lb. (0.7kg) / 2.11 lb. (0.96 kg)
16

SPECIFICATIONS
MODELNTSCPAL
Imagesensor1/3"Super‐HADIIPS960HCCD
Effectivepixels976x494976x582
Scanningsystem2:1interlace
Scanningfrequency15.734KHz(H),59.94Hz(V)15.625KHz(H),50Hz(V)
Sync.systemInternal/Linelock
Resolution650TVL
Min.illumination0.4Lux(COLOUR),0.04Lux(B/W),0.001Lux(Low‐shutter)
Videooutput1.0Vp‐p(75ohm,composite)
S/NRatio50dB(AGCOFF)
G
E
N
E
R
A
L
CameraControlRS485(Faxtrax,PelcoD,PelcoP)
WhiteBalanceAuto/CRS/Push&Hold/Indoor/Outdoor/FL/User
ExposureAuto/ManualShutter/Flickerless/LowLightControl/OffsetAdd
BLC/WDREHLC/AUTO/SPOT/ZONE/BLMWDR:x512(LevelAdjust)
AGCControlLow/Middle/High/Off
ShutterSpeed1/60‐1/10,000(Auto:1/100,000)1/50‐1/10,000(Auto:1/100,000)
Sens‐Upx32
Day/Night Auto/Day/Night/Ext
VideoAnalyticsZone/Motiontrace/Facetrace/Minefield/Absent/Cross/Entrance/
SceneChangeDetection
D‐Zoom~x256(Zoom)/D‐PTZSupport
DNR2DNR,3DNR:GainAdjust,DNRDemo
PrivacyZoneMax15(Tilt,Color,Transparency,Mosaic)
CameraTitleAlphaNumeric
DisplayOn/Off(CamID,Title)
CamID001~255
EffectV‐Flip/Mirror/Rotation/Nega&Posi/Freeze/Sharpness
BadPixel Adj/Done(Max64point),Detectedpixeldisplay
SystemLockLock/Unlock(needPasswordinputwhenLocked)
FrameControlAuto,Off~7Sec(Useforsavingstorage)
LanguageEnglish
F
U
N
C
T
I
O
N
OtherFunctionAdminPassword,AlarmSetting(Period,Snooze,Polarity)
PowersourceDC12V/AC24V±10%
Powerconsumption4.5Watts
P
O
W
E
RPowerinput2‐PinTerminalblock
VideooutputBNC,UTP(optional)
Autoirisoutput4‐Pinminidinjack(standardconnection)
LensmountFixedMount
Lenstype2.8mm~12.0mm/F1.4D&NDCIRISVari‐FocalLens
OperatingTemp.‐10ºCto+50ºC
OperatinghumidityLessthan90%
E
T
C
Externaldimension146(W)x114(H)x/Weight:770g
17

5030xxxxA
18