Auber JSL-73 User manual

1
Multi Event Timer for Beer Brewing (JSL-73B-24, V1)
This timer is designed based on commonly used beer-brewing recipe. It can help brewers track duration
of the whole boiling process and remind brewers to add hops or other ingredients at each specific time.
The relay output of the timer should be connected to a flashing buzzer (sold separately).
1. Description of the timer.
Figure 1. Front panel of the timer
1) Top LED display: In normal operation, it shows remaining time to next event. When remaining time is
longer than 99'59”, the display will show minutes only. If the ^/MUT key is pressed, it will display the
number of the upcoming event (eg. T2, T3...). When an event time is up, it will flash the event number
(T2, T3, T4, etc) until the alarm is turned off. In programming mode, it shows the parameter to be set. In
stop watch mode (NE=1, tdIr is set to Up), it will display the duration of current event.
2) Bottom LED display: In normal operation, it displays remaining time to the final stop of the timer.
When remaining time is longer than 99’59”, the display will show minutes only. In programming mode,
it shows the set value of the parameter. In stop watch mode, it will display the duration of accumulated
time that has elapsed.

2
3) Run indicator: lit when the timer is running; flash when the timer is finished/stopped; off before timer
is started or when timer is ready to start.
4) Output indicator: turns on when relay is on; turns off when relay is off. It will be on at the end of each
event for the duration of “Ad”. This light should be synchronized with the flashing buzzer that is
connected to the relay.
5) SET key. Press and hold this key for 3 second will enter the programming mode to set nE and Ad.
Press the key momentarily to set T1, T2, etc. This key is disabled when timer is running.
6) V / RST key: Decrease and reset key. When timer is running, press it to stop the timer and return to
the beginning ready state. When timer is finished, press it to stop the timer from flashing “END” and
make the timer ready for another run. In the programming mode, pressing it will decrease the set value
of the parameter. Each time you press and release, the value will decrease by one unit. But if you press
and hold it, the value will continuously decrease, as the holding time increases, the speed of number
decreasing will accelerate. You can use this feature for large number reduction. When the number is
getting close to desired value, release the key. Then, press it momentarily for fine setting adjustment.
7) ^ / MUT key: Increase and mute key. When the timer is running, press it to allow the top display
show the number of the upcoming event. (T2 ,T3, etc). When an event time is up and relay is on,
pressing this key once will turn off the relay and mute the alarm. This function only affect the relay. It
will not interrupt the running timer. In stop watch mode, press it to restart the top display as a second
timer.
In the programming mode, pressing it will increase the set value of the parameter. Each time you press
and release, the value will increase by one unit. But if you press and hold it, the value will continuously
increase, as the holding time increases, the speed of number increasing will accelerate. You can use this
feature for large number increment. When the number is getting close to desired value, release the key.
Then, press it momentarily for fine setting adjustment.
8) START key: Start key. Pressing it will start the timer. When timer finished and flashing “END”, pressing
it once will stop the flashing, making the timer ready for the next run. Pressing second time will restart
the timer. This key is disabled when timer is running. In stop watch mode, press it to start and stop the
timer.
2. Setting the Parameters.
There are only three parameters to be setup: Number of events, alarm duration and time of each event.
1) nE, The number of events are the total number of times you want the buzzer to be on. e. g. If you only
add hops at the very beginning and want the buzzer to turn on when the boiling is done, that is one
event. If you want to add another hop in the middle of boiling, it is considered two events. Up to nine
events can be set for the process.

3
When NE=1, two counting options are offered. One is counting down, just like when NE>1. The other
one is counting up. After setting NE=1, press SET key second time and use ^ or V key to set the count
direction “tdIr” to count-up(Up) or count-down(dn). Press SET key third time to confirm.
The counting down option can be used for boiling (when only one ingredient is added), or mashing at a
fixed time. It works just as when NE>1.
The counting up option is for mashing process that is finished by specific stage of starch conversion
instead of specific time. The timer functions as a stop watch by continuously counting up. It provides a
time reference for user when it is the time to check the sweet wort. The timer will not stop
automatically and activate the relay. In this mode, pressing START button will start and stop the timer,
RST button will reset the timer to zero. Pressing the MUT button will restart the top display from zero so
that it becomes the second timer.
2) Ad, Alarm duration. It is the duration that you want the buzzer to be turned on at the end of each
event. The duration of all events are the same. Ad can be set from 0 to 200. The unit is seconds. e. g.
When Ad=5, the flashing buzzer will be on for 5 second. The number 0 and 200 have different meanings.
When Ad=0, the timer will pause at the end of each event and turn on the buzzer, user need to press the
Reset key to continue the timer. This is a feature designed for old school brewing. When Ad=200, it
become “on until cancelled”. The relay will turn on until user press the mute key. Note: When the Ad is
not set to zero, the timer counting will continue when the buzzer is on.
3) TX. Time duration of each event, X is the event number. TX is the boiling time of each ingredient as
commonly used in beer recipe. For example, if hop A needs to be boiled for 60 minutes, hop B needs to
be boiled for 10 minutes. Then set T1= 60 and T2=10. When, set the time, you need to set the longest
time first and shortest time last (T1>T2>T3>….). The value of T1 sets the up limit for T2, the value of T2
sets the up limit for T3 and so on..... If you set T1=T2, event T2 will be ignored.
3. How to set nE and Ad.
Press and hold SET for 3 seconds, display will show NE. This is for setting the number of events.
Press SET again, display will show Ad. This is for setting the alarm duration.
Press SET again to exit.
4. How to set T.
Press SET momentarily, display will show T1, use up ^ and down V key to set the value and press SET to
confirm.
Note, the parameter setting change will not be saved until SET is pressed.
5. Application Example.

4
A beer recipe requires three different hops to be boiled for different time.
1 oz Hop A. boiling for 60 minutes.
1 oz Hop B, boiling for 30 minutes.
1 oz Hop C, boiling for 1 minute
We want the buzzer connected to the timer relay to run for 10 seconds when it is the time to add Hop B
and Hop C. The buzzer will also be on for 10 seconds when the 60 minutes boiling of hop A is finished
Set nE = 3, Ad =10, T1=60, T2=30, T3=1.
6. Terminal Assignment.
5
4
3
2
1
10
9
8
7
6
OUT AC/DC
24V
COMRSTMUT
START
Figure 2. Back terminal assignments
Power for the timer needs to be connected to between terminal 9 and 10. The voltage should be 24V
AC/DC. No polarity needed for 24V DC power supply.
Terminal 7 and 8 are for relay output. Terminal 7 and 8 are Normally-open (NO) contacts. When the
relay is energized (or when the OUT LED is on), terminal 8 connects to terminal 7. The relay is a “dry
switch” that does not provide power by itself. Please see the wiring example below.
Terminal 5 is the start terminal that has the same function as the START key in the front panel. Terminal
4 is the mute terminal that function the same as the “^/MUT” key in the front panel. Terminal 3 is the
reset terminal that function the same as the “V/RST” key in the front panel. Terminal 1 and 2 are the
common contacts of the terminal 3/4/5. There are two ways to operate terminal 3, 4 and 5.
1) Connecting a normally open (NO) momentary push button switch between the terminal (3, 4 or 5) to
the COM (1 or 2). Please note, the function starts when you release (or open) the button of the switch,
not when you press down the switch.
2) Connecting a DC logic signal (TTL or CMOS or voltage in the range from 3 to 30 VDC) between the
terminal (3, 4 or 5) to the COM (1 or 2). Please note, the function is rising-edge triggered. The logic signal
should normally be at high level. The function starts when the signal goes from low to high. If you have
an inverted logic signal, you need to connect a NPN transistor between terminal and COM; add 10Kohm
resistor to the gate for signal input.

5
7. Back Terminal Wiring examples.
1) Signal controlled by switches.
5
4
3
2
1
10
9
8
7
6
START
MUT
24 V AC
RST
Figure 3. Wiring example of JSL-73.
Power (24V AC) is sent to terminal 9 and 10. The external switches on terminals 2, 3, 4 and 5 should be
momentary type. They are needed only if you want to control the timer remotely. Otherwise, you can
use the front keys on the timer. The buzzer used in this example is also optional. The buzzer is powered
by the 24V AC.
2) Signal controlled by DC logic signal
5
4
3
2
1
10
9
8
7
6
+
-
24V DC
START
Figure 4. Rising-edge triggered signal. Timer and buzzer are powered by 24V DC.

6
5
4
3
2
1
10
9
8
7
6
START
24 VAC
10ke
b
cNPN
Figure 5. Inverted logic signal
Auber Instruments
5755 North Point Parkway, Suite 99
Alpharetta, GA 30022
www.auberins.com
Email: [email protected]m Tel: [phone]
Copyright 2007-2015, Auber Instruments All Rights Reserved.
No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written
consent of Auber Instruments. Auber Instruments retains the exclusive rights to all information included
in this document.