AudioCodes Mediant 2000 User manual

Fast Track Installation Guide
For Nortel H.248, SIP, H.323, MGCP
Version 4.2
Document #: LTRT00904 Rev 001

Mediant 2000
Mediant 2000 2 Document #: LTRT-00904 Rev 001
Declaration of Conformity
We AudioCodes Ltd, declare under our sole responsibility that the products:
Mediant 2000
To which this declaration relates, is in conformity with all applicable essential requirements
following the provisions of the European Directive 1999/5/EC
The conformity assessment procedure used for this declaration is the Annex-II of the Directive.
Eli Nir
V.P. R&D
25 September 2003.
Este producto està en conformidad con la directiva Europea 1999/5
Dette produkt er i overensstemmelse med Europæiske Direktiver 1999/5
Dieses Produkt ist konform mit der europäischen Richtlinie 1999/5
Ce produit est conforme aux exigences de la Directive européenne 1999/5
Questo prodotto è conforme con la normativa europea 1999/5
Este producto està em conformidade com as Diretrizes Européia 1999/5
Tuote on eurooppalaisen säännöstön mukainen 1999/5
Denna product följer europeiska direktiv 1999/5
Το προιόν, είναι σύµφωνο µετους κανονισµούς της Ευρωπαικής Κοινώτητας 1999/5
Tæki þetta er í samræmi við tilskipun Evrópusambandsins 1999/5
Dette produktet er i samhørighet med det Europeiske Direktiv 1999/5
Network Information and Intent of Use
The product is for access to ISDN at 2048 kb/s and for access to G.703 Leased lines at 2048
kb/s. Network Compatibility
The product supports all the Telecom networks in EU that comply with TBR4 and TBR13.
Telecommunication Safety
The safety status of each port is declared and detailed in the table below:
Ports Safety Status
E1 or T1 TNV-1
Ethernet (100 Base-T) SELV
TNV-1: Telecommunication network voltage circuits whose normal operating
voltages do not exceed the limits for SELV under normal operating
conditions and on which over voltages from telecommunication
networks are possible.
SELV: Safety extra low voltage circuit.

Fast Track Installation Guide Declaration of Conformity
Version 4.2 3 February 2004
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA.
On the bottom of this equipment is a label containing a product identifier in the format
US:AC1ISNANMED2KDC. If requested, this number must be provided to the telephone
company.
The telephone company may make changes in the facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens, the telephone
company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service
Should you experience trouble with this telephone equipment, please contact:
AudioCodes Inc.
San Jose, CA USA
Tel: [phone]
Do not attempt to repair this equipment!
Facility Interface Code: 04DU9.BN, 04DU9.DN, 04DU9.1KN, 4DU9.ISN
Service Order Code: 6.0N
USOC Jack Type: RJ21X or RJ48C
It this gateway causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer as soon as possible. You will also be
advised of your right to file a complaint with the FCC if you believe it is necessary.
Safety Warning
The unit may contain a Class I Laser/LED emitting device, as defined by 21 CFR 1040 and
IEC825. Avoid staring into the beam.
Prior to installation, always correctly connect the chassis to a safety ground according to
local laws. Only authorized, qualified service personnel must install and service this device.

Mediant 2000
Mediant 2000 4 Document #: LTRT-00904 Rev 001
Refer to the following AudioCodes manuals for additional information:
Mediant 2000/MGCP-MEGACO User’s Manual, Document #: LTRT-00727
Mediant 2000/H.323 User’s Manual, Document #: LTRT-00699
Mediant 2000/H.323 Release Notes, Document #: LTRT-00696
Mediant 2000/SIP User’s Manual, Document #: LTRT-00725
Mediant 2000/SIP Release Notes, Document #: LTRT-00726
TrunkPack/Mediant Series Release Notes, Document #: LTRT-00619
VoPLib User's Manual, Document #: LTRT-00844.
VoPLib API Reference Manual, Document #: LTRT-00840
Trademarks
AC logo, AudioCodes, AudioCodes logo, Mediant, MediaPack, NetCoder, Stretto,
TrunkPack, VoicePacketizer and VoIPerfect, are trademarks or registered
trademarks of AudioCodes Limited. All other products or trademarks are property
of their respective owners.
Customer Support
Customer technical support and service are provided by AudioCodes’
Distributors, Partners, and Resellers from whom the product was purchased. For
Customer support for products purchased directly from AudioCodes, contact
[e-mail].
Abbreviations and Terminology
Each abbreviation, unless widely used, is spelled out in full when first used. Only
industry-standard terms are used throughout this manual. Mediant 2000 refers to
all versions: MGCP, MEGACO, H.323 and SIP, except where identified
individually.
Notice
This Fast Track Installation Guide describes quick installation of the AudioCodes
Mediant 2000 MGCP, MEGACO, H.323 or SIP Media Gateway, operating with software
version 4.2. Information contained in this document is believed to be accurate and
reliable at the time of printing. However, due to ongoing product improvements and
revisions, AudioCodes cannot guarantee the accuracy of printed material after the Date
Published nor can it accept responsibility for errors or omissions. Updates to this
document and other documents can be viewed by registered Technical Support
customers at www.audiocodes.com under Support / Product Documentation.
© 2004 AudioCodes Ltd. All rights reserved.
This document is subject to change without notice.
Refer to the current release notes that may be included with your documentation or
hardware delivery.
Date Published: Feb-11-2003 Date Printed: Feb-12-2004

Fast Track Installation Guide Contents
Version 4.2 5 February 2004
Table of Contents
1Quickly Setting Up the Mediant 2000.........................................................................6
2Installing the Mediant 2000.........................................................................................7
2.1 Unpacking .....................................................................................................7
2.2 Package Contents ...............................................................................................7
2.3 Installing the Mediant 2000 in 19-inch Rack or on Desktop.................................8
2.3.1 Installing a Mediant 2000 in a 19-inch Rack ...........................................8
2.3.2 Installing the Mediant 2000 on a Desktop...............................................8
2.4 Cabling the Mediant 2000 ...................................................................................8
3Getting Started...........................................................................................................12
3.1 Correlating PC / Mediant 2000 IP Address & Subnet Mask ..............................12
3.2 Accessing AudioCodes’ Embedded Web Server ..............................................13
3.3 Setting Mediant 2000 IP Address / Subnet Mask ..............................................13
3.4 Restoring Your PC’s IP Address / Subnet Mask ...............................................13
4Configuring MGCP-MEGACO Parameters...............................................................14
5Configuring H.323 Parameters .................................................................................16
6Configuring SIP Parameters .....................................................................................18
7Monitoring Channels – All Protocols.......................................................................19
8Trunk Configuration ..................................................................................................21
9Downloading Software Updates...............................................................................23
10 Monitoring/Diagnosing the Mediant 2000................................................................25
List of Figures
Figure 2-1: Mediant 2000 Front Panel (16 trunks)............................................................... 7
Figure 2-2: Mediant 2000 Rear Connectors (16 trunks, AC power) .................................... 9
Figure 2-3: Mediant 2000 Rear Panel Cabling (16 trunks, AC power) .............................. 10
Figure 2-4: 50-pin Female Telco Board-mounted Connector ............................................ 10
Figure 2-5: Mediant 2000 Rear Panel Cabling (8 trunks, DC power)) ............................... 11
Figure 2-6: Pinout of RJ-48c Trunk Connectors................................................................ 11
Figure 2-7: Pinout of RJ-45 LAN Connectors.................................................................... 11
Figure 3-1: Enter Network Password Prompt.................................................................... 13
Figure 4-1: Mediant 2000/MGCP-MEGACO Quick Setup................................................. 14
Figure 5-1: Mediant 2000/H.323 Quick Setup ................................................................... 16
Figure 5-2: Trunk Group Table.......................................................................................... 17
Figure 5-3: Tel to IP Routing Table ................................................................................... 17
Figure 6-1: Mediant 2000/SIP Quick Setup....................................................................... 18
Figure 7-1: Trunk & Channel Status.................................................................................. 19
Figure 7-2: Specific Channel Status Details...................................................................... 20
Figure 8-1: Trunk Configuration Screen ............................................................................ 21
Figure 9-1: Downloading Software Updates...................................................................... 24
Figure 10-1: Mediant 2000 Front Panel............................................................................. 25
List of Tables
Table 2-1: Mediant 2000 Cables and Cabling Procedures.................................................. 9
Table 2-2: E1/T1 Connections on each 50-pin Telco Connector....................................... 10
Table 3: Mediant 2000 Default IP Address / Subnet Mask................................................ 12
Table 10-1: Mediant 2000 Front Panel LED Indications.................................................... 25

Mediant 2000
Mediant 2000 6 Document #: LTRT-00904 Rev 001
1 Quickly Setting Up the Mediant 2000
 To quickly set up the Mediant 2000, follow these 7 procedures:
Install the Mediant-2000
Configure Call Control
Parameters
Set Mediant 2000
IP & Subnet Mask
Access the Embedded
Web Server
Correlate PC's IP/Subnet
Mask with Mediant 2000
Cable & Connect
1
2
3
4
6
Configure Trunks'
PSTN Protocol
7
5
Configure
MGCP
Parameters
Configure
MEGACO
Parameters
Configure
H.323
Parameters
Configure
SIP
Parameters
Refer to Section 2.4
Refer to Section 3.1
Refer to Section 3.2
Refer to Section 3.3
R
e
f
e
r
to
Sect
i
o
n 2
Refer to Sections 4 to 6
Refer to Section 8

Fast Track Installation Guide Installing the Mediant 2000
Version 4.2 7 February 2004
2 Installing the Mediant 2000
2.1 Unpacking
 To unpack:
 Open the carton and remove packing materials
 Remove the Mediant 2000 Media Gateway from the carton
 Check that there is no equipment damage
 Check, retain and process any documents
 Notify AudioCodes of any damage or discrepancies
 Retain any diskettes or CDs
2.2 Package Contents
Ensure that the Mediant 2000 package contains (in addition to the device):
 For the dual AC power supply version of the Mediant 2000 (documented in
this Guide), two AC power cables are supplied; for the single AC power
supply version of the Mediant 2000, 1 AC power cable is supplied.
 CD (software and documentation)
 Plastic envelope containing 2 brackets and bracket-to-device screws for 19-
inch rack installation option
Figure 2-1: Mediant 2000 Front Panel (16 trunks)
The 8-trunk device’s front panel is similar to the 16-trunk device’s front panel
(refer to Figure 2-1), except for trunks 9-16 and corresponding LEDs.
The 4-trunk, 2-trunk and 1-trunk devices’ front panels are similar in appearance
to the 8-trunk device’s front panel.
If the device supports 1 trunk, only the first LED is functional; if 2 trunks, the first
two LEDs are functional; if 4 trunks, the first four LEDs are functional.
cPCI board locking
screws
cPCI latch Front panel LEDs (refer to
Section 10) cPCI latch
A
udioCodes’ TP-1610 cPCI
board, 16-trunk configuration

Mediant 2000
Mediant 2000 8 Document #: LTRT-00904 Rev 001
2.3 Installing the Mediant 2000 in 19-inch Rack or on
Desktop
AudioCodes’ Mediant 2000 can be installed, as required, on a desktop or in a
standard 19-inch rack. Refer to Section 2.4 for cabling the device.
2.3.1 Installing a Mediant 2000 in a 19-inch Rack
Two brackets, supplied in a plastic envelope, must be attached to the flanks of
the device to enable installation in a rack.
 To install the Mediant 2000 in a 19-inch rack:
1. Remove the 2 screws nearest the front panel on either side of the device.
2. Align a bracket over 2 holes on one side (so that the bracket’s larger holes
face front) and with the 2 replacement screws supplied, screw in the bracket.
3. Perform the same procedure on the other side.
4. Insert the Mediant 2000 into the rack, line up the bracket holes with the rack
frame holes, and use 4 standard rack screws (not supplied) to secure the
brackets to the rack frame, and cable it as in Section 2.4. Note that there is an
option for additional rear brackets.
2.3.2 Installing the Mediant 2000 on a Desktop
No brackets are required. Simply place the device on the desktop in the position
you require and cable it as in Section 2.4.
2.4 Cabling the Mediant 2000
Refer to Table 2-1 on page 9 for the rear panel cables and cabling procedures.
Refer to Figure 2-2 for the rear connectors on the 16- trunk version. Refer to
on page 10 for the rear connectors on the 8-trunk version. Note that the Mediant
2000 is available in all configuration combinations, i.e., AC or DC, in the 16-trunk,
8-trunk, 4-trunk, 2-trunk or 1-trunk device. The 16-trunk AC and the 8-trunk DC
configuration combinations are illustrated here as representative.

Fast Track Installation Guide Installing the Mediant 2000
Version 4.2 9 February 2004
Figure 2-2: Mediant 2000 Rear Connectors (16 trunks, AC power)
Table 2-1: Mediant 2000 Cables and Cabling Procedures
Cable Cabling Procedure
10/100 Base-T
Ethernet cable
Connect the 10/100 Base-T RJ-45 ETHERNET port directly to the PC
network port with a crossed Ethernet cable (when changing the IP
address). After changing the IP address, connect both ports to the IP
network, using standard Ethernet cables. One port is for redundancy.
50-pin Telco
cable
Customers assembling the 50-pin Telco cable connector must wire it
according to the pinout in Figure 2-4 and Table 2-2 on page 10. Attach
the (male) Telco cable connector to the 50-pin (female) connector on
the Rear Transition Module (RTM). Connect the other end to the
PBX/PSTN switch.
Grounding Permanently connect the device to a suitable ground with the
grounding screw on the rear connector panel, using 14-16 AWG wire.
Power cable
(for single AC) Connect the 100-240V~50-60 Hz power socket to the mains using the
supplied cord (with the single AC power supply version of the device).
Two power
cables (for dual
AC)
Connect each of the dual 100-240V~50-60 Hz power sockets to
separate mains circuits (for power source redundancy) using the two
supplied cords (with the dual AC power supply version of the device)
DC power cord Connect the wire’s 2-pin female to its mating on the terminal block. The
DC version is equipped with a -48 VDC (floating) inlet. Use #14-16
AWG cables for the DC connection.
 To cable the Mediant 2000, take the following 6 steps:
1. Connect the power supply using either the IEC32 connector cable (supplied)
for the AC version (refer to Figure 2-2 and Figure 2-3) or the 2-pin connector
for the DC version (refer to to Figure 2-5).
Two 50-pin
Telco female
connectors
Two
Ethernet
RJ-45
p
orts
Grounding
screw Dual IEC320
type inlets

Mediant 2000
Mediant 2000 10 Document #: LTRT-00904 Rev 001
2. When using the 16-trunk device (with two 50-pin Telco E1/T1 connectors on
the RTM), connect a cable to the connector labeled “Trunks 1→8”; connect
the 2nd cable to the connector labeled “Trunks 9→16”. These two 50-pin
female Telco connectors on the RTM are shown in Figure 2-4 on page 10
and detailed in Table 2-2 on the same page.
Figure 2-3: Mediant 2000 Rear Panel Cabling (16 trunks, AC power)
Figure 2-4: 50-pin Female Telco Board-mounted Connector
125
26
50
Pin Numbers
Table 2-2: E1/T1 Connections on each 50-pin Telco Connector
E1/T1 Number
1 to 8 9 to 16 Tx Pins (Tip/Ring) Rx Pins (Tip/Ring)
1 9 27/2 26/1
2 10 29/4 28/3
3 11 31/6 30/5
4 12 33/8 32/7
5 13 35/10 34/9
6 14 37/12 36/11
7 15 39/14 38/13
8 16 41/16 40/15
3. When using an 8-trunk device (or 4 or 2 or 1-trunk device) with eight RJ-48c
E1/T1 ports (or 4 or 2 or 1, respectively), connect E1/T1 cables to the ports
(labeled “Trunks 1 to 8” in the case of the 8-trunk device) (refer to Figure 2-5
on page 11).
Category 5 LAN
cables, connected
to the ETHERNET 1
and 2 RJ-45 ports
Two 50-pin Telco
connector cables,
each supporting 8
trunks
Dual AC power
cables, for
redundancy
Grounding
screw

Fast Track Installation Guide Installing the Mediant 2000
Version 4.2 11 February 2004
RJ-48c trunk connectors are wired according to Figure 2-5 below.
Figure 2-5: Mediant 2000 Rear Panel Cabling (8 trunks, DC power))
Figure 2-6: Pinout of RJ-48c Trunk Connectors
1 2 3 4 5 6 7 8 3, 6, 7, 8
not connected
body = shield
1 = Rx-
2 = Rx+
4 = Tx-
5 = Tx+
RJ-48c Trunk Connector and Pinout
4. Connect a Category 5 LAN cable to an Ethernet RJ-45 port (and the other as
optional redundancy/backup) to your IP network. Connect the other end of
the Category 5 LAN cable to your IP network. The RJ-45 connectors are
wired according to Figure 2-7.
5. Permanently connect the device to a suitable ground with the grounding
screw on the rear connector panel, using 14-16 AWG wire.
Figure 2-7: Pinout of RJ-45 LAN Connectors
1 2 3 4 5 6 7 8
RJ-45 LAN Connector and Pinout
4, 5, 7, 8
not connected
1 = Tx+
2 = Tx-
3 = Rx+
6 = Rx-
6. Power up the device; installation is now complete.
Category 5 LAN
cable, connected to
the ETH 1 RJ-45 port
8 RJ-48c ports,
each supporting
a trunk
2-pin connector
for DC
Grounding
screw

Mediant 2000
Mediant 2000 12 Document #: LTRT-00904 Rev 001
3 Getting Started
AudioCodes’ Mediant 2000 application software already resides in the device’s
flash memory when it is supplied (with factory default parameters). Mediant 2000
devices are also supplied with an Embedded (integrally stored) Web Server,
used to configure the device and monitor it during run time. Modifications made
to the Mediant 2000 via the Embedded Web Server (not explicitly requiring a
reset) are “on-the-fly” and do not affect service.
AudioCodes’ Embedded Web Server enables Users to:
 Set the Mediant 2000 device’s IP address & Subnet Mask (refer to Section
3.3 on page 13)
 Configure control protocol parameters:
 MGCP/MEGACO (refer to Section 4 on page 14)
 H.323 (refer to Section 5 on page 16)
 SIP (refer to Section 6 on page 18)
 Monitor trunk and channel status (refer to Figure 7-1 on page 19)
 Download software updates (refer to Section 9 on page 23)
3.1 Correlating PC / Mediant 2000 IP Address &
Subnet Mask
Before using your Web browser to access the Mediant 2000 device’s Embedded
Web Server, change your PC’s IP address and Subnet Mask to correspond with
the Mediant 2000’s factory default IP address and Subnet Mask, shown in Table
3. For details on changing the IP address and Subnet Mask of your PC, refer to
Windows™ Online Help (Start>Help).
Table 3: Mediant 2000 Default IP Address / Subnet Mask
E1/T1 Trunks IP Address Subnet Mask
Trunks 1-8 10.1.10.10 255.255.0.0
Trunks 9-16 10.1.10.11 255.255.0.0
Note: The two IP addresses (one IP address for Trunks 1-8 and one for Trunks 9-16)
refer to two different modules (AudioCodes’ TPM-1100), which reside in the
same board (AudioCodes’ TP-1610) inside the Mediant 2000.
Note: Write down the IP Address and Subnet Mask you assign the device. Do the
same when defining User Name and Password (refer to Section 3.2 on page
13). If the Embedded Web Server is unavailable (for example, if you’ve lost your
User Name and Password), use AudioCodes’ BootP/TFTP Server to access the
device, “reflash” the load and reset the password (refer to the Mediant 2000
User’s Manual for detailed information on using a BootP/TFTP server to access
the Mediant 2000).

Fast Track Installation Guide Getting Started
Version 4.2 13 February 2004
3.2 Accessing AudioCodes’ Embedded Web Server
 To access the Embedded Web Server:
1. Open any standard Web-browsing application such as Microsoft™ Internet
Explorer™ (Ver. 5.0 and higher) or Netscape™ Navigator™ (Ver. 7.0 and
higher).
2. Specify the IP address of the Media Gateway in the ‘Address’ field (e.g.,
http://10.1.10.10); the Embedded Web Server ‘Enter Network Password’
screen appears, shown in Figure 3-1.
Figure 3-1: Enter Network Password Prompt
3. Enter the User Name (default: Admin), and Password (default: Admin),. Note
that the User Name and Password fields are case-sensitive. Click OK; the
‘Quick Setup’ screen is accessed, shown respectively in Figure 4-1 on page
14 (MGCP/MEGACO), Figure 5-1 on page 16 (H.323), and Figure 6-1 on
page 18 (SIP).
3.3 Setting Mediant 2000 IP Address / Subnet Mask
 To set the Mediant 2000 IP Address / Subnet Mask:
 In ‘Quick Setup’, set the Mediant 2000 ‘IP Address’ and ‘Subnet Mask’ fields
under ‘IP Configuration’ to correspond with your network IP address settings;
click ‘RESET’ and click OK in the prompt.
3.4 Restoring Your PC’s IP Address / Subnet Mask
After setting the Mediant 2000 IP address/Subnet Mask, restore your PC’s IP
address and Subnet Mask to what it originally was. If necessary, restart your PC
and re-access the Mediant 2000 via the Embedded Web Server with its new IP
address, to configure the device (refer to Section 4).

Mediant 2000
Mediant 2000 14 Document #: LTRT-00904 Rev 001
4 Configuring MGCP-MEGACO Parameters
This section describes configuration of basic MGCP-MEGACO parameters, using
a standard Web browser such as Microsoft™ Internet Explorer™ (Ver. 5.0 and
higher) or Netscape™ Navigator™ (Ver. 7.0 and higher) to access the
Embedded Web Server.
 To configure basic MGCP-MEGACO parameters take th next 12 steps:
Figure 4-1: Mediant 2000/MGCP-MEGACO Quick Setup
1. Define fields “DNS Primary Server IP” and “DNS Secondary Server IP” (if
your network features a DNS server; clarify with your Network
Administrator).
2. Under the section “Trunk Configuration”, select “Protocol Type” and
“Framing Method”. (For E1 trunks, always set the Framing Method to
Extended Super Frame). Note that the Trunk Configuration parameters
are global, and apply to all trunks. To configure trunks per trunk, refer to
Section 8 on page 21.
3. Select the Clock Master (the trunk clock source) from the drop-down list:
Choose either ‘Recovered’ (the clock is recovered from the trunk; default)
or ‘Generated’ (the trunk clock source is provided by the internal/TDM
bus clock source, depending on the parameter ‘TDM Bus Clock Source’
(Advanced Configuration > TDM Bus Settings)
4. Select the Line Code. Choose either B8ZS (bipolar 8-zero substitution)
for T1 trunks only; HDB3 (high-density bipolar 3) for E1 trunks only; or
AMI (for both T1 and E1).
5. Define the “Call Agent IP” if your network doesn’t feature a DNS server
that will automatically define the Call Agent’s IP address. If you have a
DNS server, the field is optional.

Fast Track Installation Guide Configuring MGCP-MEGACO Parameters
Version 4.2 15 February 2004
6. Define the “Call Agent Port”. The default is 2427.
7. Enter the “Call Agent Domain Name”. When using the DNS server
option, enter the Domain Name of the Call Agent operating with the
Mediant 2000. The DNS server will automatically deduce the Call
Agent’s IP address from the Domain Name.
8. Assign a name to the device in the “Gateway Name” field. (For example:
‘gateway1.com’). Ensure that the name you choose is the one that the
Call Manager/Agent is configured with to identify your Mediant 2000.
9. If you’re working with MGCP, define an “Endpoint Prefix”. Ensure that the
prefix you choose is the one that the Call Manager/Agent is configured
with to identify your device.
10. Define a “Trunk Name”. Ensure that the name you choose is the one that
the Call Manager/Agent is configured with to identify your Mediant 2000.
11. If you’re working with MEGACO, define an “Endpoint Name”. Ensure that
the name you choose is the one that the Call Manager/Agent is
configured with to identify your device.
12. Click the RESET button and click OK in the prompt; wait approx. 60
seconds; the Ready and LAN LEDs on the front panel are lit green. Now
you can operate your phones according to your specific configurations.
Use the “Advanced Configuration” and “Protocol Management” screens to modify
all other Mediant Gateway parameters.
For detailed directions of operating under Web management control, refer to
Section 6.2 of the Mediant 2000/MGCP-MEGACO User’s Manual, Document #:
LTRT-00698.
Now continue with Section 7 Monitoring Channels – All Protocols on page
19 until the end of this guide.

Mediant 2000
Mediant 2000 16 Document #: LTRT-00904 Rev 001
5 Configuring H.323 Parameters
This section describes configuration of basic H.323 parameters, using a standard
Web browser such as Microsoft™ Internet Explorer™ (Ver. 5.0 and higher) or
Netscape™ Navigator™ (Ver. 7.0 and higher) to access the Embedded Web
Server.
 To configure basic Mediant 2000/H.323 parameters:
Figure 5-1: Mediant 2000/H.323 Quick Setup
1. Set the parameters under the ‘H323 Parameters’ section, shown in Figure
5-1:
•When using a Gatekeeper set the “Working with Gatekeeper” field to
“Yes” and specify the primary Gatekeeper’s IP address in the
“Gatekeeper IP Address” field.
•Leave parameters “Enable Annex D/T.38 Fax Relay” and “Coder” at their
defaults unless your technical requirements differ.
2. Open the “Trunk Group Table” and configure the E1/T1 “B” channels to be
activated (refer to Figure 5-2 on page 17). For example, for four T1 trunks,
enter “0-95” in the “Channels” field and the starting phone number, such as
1001, in the adjacent “Phone Number” field; phone numbers 1001 to 1096
are automatically allocated to the channels. These are virtual numbers, used
only to define enabled B-channels. For eight T1 trunks, set the “Channels”
field to “0-191”.
3. After configuring, press the ‘SUBMIT’ button and close the window.

Fast Track Installation Guide Configuring H.323 Parameters
Version 4.2 17 February 2004
Figure 5-2: Trunk Group Table
4. Open the “Tel to IP Routing Table” (when working without a Gatekeeper, this
internal routing table must be defined). Configure the “Destination Phone
Prefix” (the prefix of the called number) and its associated “IP Address”. In
Figure 5-3 (example), an incoming call with the called number starting with
10xx or 20xx is sent to IP address 10.2.32.160. When a Gatekeeper is used,
the routing table can be used optionally as fallback.
Figure 5-3: Tel to IP Routing Table
5. After configuring, click the ‘SUBMIT’ button and close the window. Reset the
device by clicking the ‘RESET’ button in the main screen. Wait about 60
seconds and refresh the Web page.
6. For trunk configuration, refer to Section 8 on page 21.
Use the “Advanced Configuration” and “Protocol Management“ screens to modify
all other H.323 parameters.
For detailed directions of operating under Web management control, refer to the
Mediant 2000/H.323 User’s Manual, Document #: LTRT-00699 Rev H01.
Now continue with Section 7 Monitoring Channels – All Protocols on page
19 until the end of this guide.

Mediant 2000
Mediant 2000 18 Document #: LTRT-00904 Rev 001
6 Configuring SIP Parameters
This section describes configuration of basic SIP parameters, using a standard
Web browser such as Microsoft™ Internet Explorer™ (Ver. 5.0 and higher) or
Netscape™ Navigator™ (Ver. 7.0 and higher) for Embedded Web Server access.
 To configure basic Mediant 2000/SIP parameters:
Figure 6-1: Mediant 2000/SIP Quick Setup
1. Set the parameters under the ‘SIP Parameters’ section, shown in Figure 6-1:
•Enter the Mediant 2000 Domain Name in the field ‘Gateway Name’. If the
field is not specified, the Mediant 2000’s IP address is used instead
(default).
•Leave the field ‘Working with Proxy’ at its default (‘No’) when no Proxy is
used (when only the internal routing fields are used to route the phones).
Otherwise, when working with Proxy, select ‘Yes’ and enter the IP
address of the Proxy IP Server in the field ‘Proxy IP Address’.
•If the ‘Proxy Name’ field is used, it will replace the "Proxy IP Address" in
all SIP messages. This means that messages will still be sent to the
physical “Proxy IP Address” but the “TO” field will contain the ‘Proxy
Name’ instead.
•Configure ‘Enable Registration’ to ‘Yes’ or ‘No’. ‘No’ = the Mediant 2000
will not register to the Proxy (default); ‘Yes’ = the Mediant 2000 will
register to the Proxy at power up.
•Select the coder that best suits your VoIP system requirements. The
default coder is: G7231 (30 msec).

Fast Track Installation Guide Monitoring Channels
Version 4.2 19 February 2004
Note: From this step on, routing the phones in the internal routing tables is similar in
SIP and H.323, therefore refer to Step 2 on page 16, until the reset in Step 5.
(Note that the equivalent of the Gatekeeper in H.323 is the Proxy in SIP.)
For detailed directions of operating under Web management control, refer to
Section 6.2 of the Mediant 2000/SIP User’s Manual, Document #: LTRT-00725
Rev 001.
Use the “Advanced Configuration” and “Protocol Management” screens to modify
all other SIP parameters.
Now continue with Section 7 below, until the end of this guide.
7 Monitoring Channels – All Protocols
 To monitor status & detail of all channels take these 2 steps:
1. Click the ‘Status & Diagnostics’ menu>’Channel Status’; the ‘Channel Status’
screen opens (Figure 7-1), the color-coding showing the Status of each
channel individually.
Figure 7-1: Trunk & Channel Status
2. To view the status of a specific channel, click on it and the Specific Channel
Status Details are displayed as shown in Figure 7-2 on page 20.

Mediant 2000
Mediant 2000 20 Document #: LTRT-00904 Rev 001
Figure 7-2: Specific Channel Status Details