Teltonika RUT240 User manual

RUT240
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

DATASHEET // RUT240
HARDWARE
POWER SOCKET PINOUT
FRONT VIEW
BACK VIEW
2
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
Mobile network
type LEDs
SIM holder
Reset button
WiFi antenna
connector Mobile AUX antenna connector Mobile MAIN antenna connector
LAN LED WAN LED
LAN port WAN port
Power socket
Power LED
Mobile signal
strength indication
LEDs

3
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps
Possibility to use different PDNs for multiple network access and services (not available in standard FW)
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS,
scheduled SMS, SMS autoreply, SMPP
Operator black/white list
Band lock, Used band status display
Auto APN
Direct connection (bridge) between mobile ISP and device on LAN
Router assigns its mobile WAN IP address to another device on LAN
Passthrough
APN
Bridge
SSID stealth mode and access control based on MAC address
Up to 50 simultaneous connections
WiFi users
SSID
Black/White list
Band management
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, RIPng, OSPF6)
Static and dynamic IP allocation, DHCP Relay, Relayd
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPnP, SSH, DHCP, Telnet
client, SNMP, MQTT, Wake On Lan (WOL)
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
Connection monitoring
Network protocols
VoIP passthrough support
Routing
DHCP
Port forward, traffic rules, custom rules
Traffic priority queuing by source/destination, service, protocol or port, traffic priority queuing by source/destination, service,
protocol or port, WMM, 802.11e
Supported >25 service providers, others can be configured manually
VRRP, Mobile, Wired and WiFi WAN options, each of which can be used as backup, using automatic Failover
Balance your internet traffic over multiple WAN connections
Load balancing
DDNS
Network backup
Possibility to mount remote file system via SSH protocol (not available in standard FW)
SSHFS (optional)
Firewall
QoS / Smart Queue
Management (SQM)
Status Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID
Multiple PDN (optional)
WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation
IEEE 802.11b/g/n, Access Point (AP), Station (STA)Wireless mode
WiFi security
1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
1 x WAN port (can be configured to LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto
MDI/MDIX
WAN
LAN
SMS
MOBILE
Mobile module
WIRELESS
ETHERNET
NETWORK
Captive portal (Hotspot), internal/external Radius server, built in customizable landing page
Wireless Hotspot
DATASHEET // RUT240
Pre-shared key, digital certificates, X.509 certificates
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN,
SYN-RST, X-mas, NULL flags, FIN scan attacks)
Attack prevention
Authentication
Firewall
Port and tag based VLAN separation
Set up custom data limits for the SIM card
VLAN
Mobile quota control
Blacklist for blocking out unwanted websites, whitelist for specifying allowed sites only
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
WEB filter
Access control
SECURITY
FEATURES
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

Respond to one ID in range [1;255] or any
Allow access through WAN
Allow Remote Access
ID filtering
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS
TCP Slave functionality
Custom registers
MODBUS TCP SLAVE
4
Multiple clients and server can be running simultaneously, 12 encryption methods
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC,
AES-192-CBC, AES-256-CBC
01, 02, 03, 04, 05, 06, 15, 16
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB,
BADC)
OpenVPN Encryption
VPN
OpenVPN
Firmware update from sever, automatic notification
FOTA
HTTP/HTTPS, status, configuration, FW update, CLI ,troubleshoot, event log, system log, kernel log
MONITORING & MANAGEMENT
WEB UI
MODBUS TCP MASTER
IKEv1, IKEv2, supports up to 4 x VPN IPsec tunnels (instances), with 5 encryption methods (DES, 3DES, AES128, AES192, AES256)
GRE tunnel
IPsec
GRE
Client/Server services can run simultaneously
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the programs' code
PPTP, L2TP
Stunnel
SSTP client instance support
ZeroTier VPN
SSTP
ZeroTier
SSH (v1, v2)
SMS status, SMS configuration, send/read SMS via HTTP POST/GET
SSH
SMS
Reboot, Status, WiFi on/off, Mobile data on/off, Output on/off
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
Call
TR-069
MQTT Broker, MQTT publisher
SNMP (v1, v2, v3), SNMP trap
MQTT
SNMP
Management API over HTTP/HTTPS
JSON-RPC
MODBUS TCP status/control
Teltonika Remote Management System (RMS)
MODBUS
RMS
Supported functions
HTTP(S), MQTT, Azure MQTT
Allows sending commands and receiving data from Modbus Master through MQTT broker
MODBUS DATA TO SERVER
Protocol
MQTT GATEWAY
MQTT gateway
Supported data formats
WireGuard VPN client and server supportWireGuard
DATASHEET // RUT240
IoT PLATFORMS
Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer,
Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID,
Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server
Azure IoT Hub
Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal
Strength, WAN Type and IP
Cumulocity
Allows monitoring of: Device data, Mobile data, Network info, Availability
Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
Clouds of things
ThingWorx
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

5
SYSTEM CHARACTERISTICS
FIRMWARE / CONFIGURATION
FIRMWARE CUSTOMIZATION
POWER
PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM)
Atheros Hornet, MIPS 24Kc, 400 MHz
CPU
64 MB, DDR2
16 MB, SPI Flash
RAM
FLASH storage
Update FW from file, check FW on server, configuration profiles, configuration backup, restore point
WEB UI
Update FW/configuration from server
Update FW/configuration for multiple devices
FOTA
RMS
Update FW without losing current configuration
Keep settings
RutOS (OpenWrt based Linux OS)
Operating system
Busybox shell, Lua, C, C++
SDK package with built environment provided
Supported languages
Development tools
4 pin industrial DC power socket
Connector
9 – 30 VDC, reverse polarity protection, surge protection >33 VDC 10us max
Passive PoE over spare pairs (available from HW revision 0007 and batch number 0010). Possibility to power up through LAN
port, not compatible with IEEE802.3af, 802.3at and 802.3bt
Input voltage range
PoE (passive)
< 6.5 W Max
Power consumption
2 x RJ45 ports, 10/100 Mbps
Ethernet
1 x Digital Input, 1 x Digital Output on 4 pin power connector
3 x Connection type status LEDs, 5 x Connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED
I/Os
Status LEDs
1 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V, external SIM holder
SIM
1 x 4 pin DC connector
2 x SMA for LTE, 1 x RP-SMA for WiFi antenna connectors
Power
Antennas
Reboot/Factory reset button
Reset
DATASHEET // RUT240
PHYSICAL SPECIFICATION
OPERATING ENVIRONMENT
Aluminium housing with DIN rail mounting option, plastic panels
83 x 25 x 74 mm
125 g
Casing material
Dimensions (W x H x D)
-40 C to 75 C
10 % to 90 % non-condensing
Operating temperature
Operating humidity
Bottom and sideways DIN rail mounting slots
Weight
Mounting options
IP30
Ingress Protection Rating
REGULATORY & TYPE APPROVALS
CE/RED, FCC, IC/ISED, EAC, RCM, PTCRB, RoHS, WEEE, Wi-Fi Certified, CCC, Anatel, GCF, REACH, Thailand NBTC, Ukraine UCRF,
SDPPI (POSTEL)
Verizon, AT&T
Regulatory
Operator
ECE R10 (E-mark)
Vehicle
INPUT/OUTPUT
1 x Digital input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high
Input
1 x Digital open collector output, max output 30 V, 300 mA
SMS, EMAIL, RMS
Output
Events
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

EN 61000-4-3:2006 + A1:2008 + A2:2010
EN 61000-4-4:2012
RS
EFT
EN 61000-4-5:2006
Surge immunity
(AC Power Line)
EN 61000-4-5:2014, clause 7.1 of ITU-T K21
EN 61000-4-6:2009
Surge immunity
(Ethernet ports)
CS
EN 61000-4-11:2004
DIP
6
EMI IMMUNITY
Draft EN 301 489-1 V2.2.0, Draft EN 301 489-17 V3.2.0, Draft EN 301 489-52 V1.1.0
FCC 47 CFR Part 15B (2017), ANSI C63.4 (2014)
EN61000-4-2:2009
Standards
RF
EN 300 328 V2.1.1, EN 301 511 V12.5.1, EN 301 908-1 V11.1.1, EN 301 908-2 V11.1.1, EN 301 908-13 V11.1.1
FCC 47 CFR Part 15C (2017), FCC 47 CFR Part 2 (2017), FCC 47 CFR Part 22H (2017), FCC 47 CFR Part 24E (2017), FCC 47 CFR Part
27C (2017)
RSS-Gen Issue 4 (2014), RSS-247 Issue 2 (2017), RSS-132 Issue 3 (2013), RSS-133 Issue 6 (2013), RSS-139 Issue 3, RSS-130 Issue 1
AS/CA S042.1:2018, AS/ACIF S042.3:2005, AS/CA S042.4:2018, AS/NZS 4268:2017
Standards
SAFETY
IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013
AS/NZS 60950.1:2015
EN 50665:2017, EN 62311:2008
FCC 47 CFR Part 1 1.1310
RSS-102 Issue 5 (2015)
Standards
ESD
DATASHEET // RUT240
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

7
DATASHEET // RUT240
1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
2. Use login information shown in image A when prompted for authentication.
3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters,
including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with
the router's WebUI before you change the password.
4. When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the
router's main operating parameters.
5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting
the antennas or changing the location of your device to achieve the best signal conditions.
A. B.
admin
admin01
Bytes received/sent*
SIM card slot in use
Data connection state
State
-65 dBm
Connected
Registered (home); OPERATOR; 4G (LTE)
Ready
348.7 KB / 223.5 KB
LOGIN TO DEVICE
1. Push the SIM button with the SIM needle.
2. Pull out the SIM holder.
3. Insert your SIM card into the SIM holder.
4. Slide the SIM holder back into the router.
5. Attach Mobile and WiFi antennas.
6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
7. Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to
LAN port.
HARDWARE INSTALLATION
*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.
Bundled accessories specifications*
Radio specifications
RF technologies
Max RF power
2G, 3G, 4G, WiFi
33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@ WiFi
Mobile antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector
Power adapter Input: 0.4A@100-240VAC, Output: 9VDC, 1A, 4-pin plug
WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector
TECHNICAL INFORMATION
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

8
STANDARD PACKAGE CONTAINS*
• Router RUT240
• 9 W PSU
• 2 x LTE antennas (swivel, SMA male)
• 1 x WiFi antenna (swivel, RP-SMA male)
• Ethernet cable (1.5 m)
• SIM Adapter kit
• QSG (Quick Start Guide)
• RMS Flyer
• Packaging box
DATASHEET // RUT240
WHAT'S IN THE BOX?
* For all standard order codes standard package contents are the same, execpt for PSU.
ROUTER RUT240 9 W PSU
1 X WIFI ANTENNA (SWIVEL, RP-SMA
MALE)
ETHERNET CABLE (1.5 M)
2 X LTE ANTENNAS (SWIVEL, SMA
MALE)
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
SIM ADAPTER KIT

9
DATASHEET // RUT240
PRODUCT CODE PACKAGE CONTAINSHS CODE HTS CODE
STANDARD ORDER CODES
RUT240 06E000
For more information on all available packaging options – please contact us directly.
851762 8517.62.00 Standard package with Euro PSU
RUT240 01U000 851762 8517.62.00 Standard package with US PSU
RUT240 02U000 851762 8517.62.00 Standard package with US PSU
PRODUCT CODE FREQUENCYREGION (OPERATOR)
AVAILABLE VERSIONS
RUT240 *8****
The price and lead-times for region (operator) specific versions may vary. For more information please contact us.
1 - Router is not certified on T-Mobile, Bell network (In progress).
Europe, the Middle East, Africa,
Korea, Thailand, India, Malaysia
4G (LTE-FDD): B1, B3, B7, B8, B20, B28A
4G (LTE-TDD): B38, B40, B41
3G: B1, B8
2G: B3, B8
RUT240 *0**** Europe, the Middle East, Africa,
Korea, Thailand, India, Malaysia
4G (LTE-FDD): B1, B3, B5, B7, B8, B20
4G (LTE-TDD): B38, B40, B41
3G: B1, B5, B8
RUT240 *1**** North America (AT&T, Bell, T-Mobile)1
RUT240 *2**** North America (Verizon)
4G (LTE-FDD): B2, B4, B12
3G: B2, B4, B5
4G (LTE-FDD): B4, B13
2G: B3, B8
RUT240 *4**** South America, Australia, New
Zealand, Taiwan
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B28
4G (LTE-TDD): B40
3G: B1, B2, B5, B8
2G: B2, B3, B5, B8
RUT240 *7**** Global
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B12,
B13, B18, B19, B20, B25, B26, B28
4G (LTE-TDD): B38, B39, B40, B41
3G: B1, B2, B4, B5, B6, B8, B19
2G: B2, B3, B5, B8
RUT240 *0*00G Europe, the Middle East, Africa,
Korea, Thailand, India (Vodafone)
4G (LTE-FDD): B1, B3, B5, B7, B8, B20
4G (LTE-TDD): B38, B40, B41
3G: B1, B5, B8
2G: B3, B8
RUT240 *6**** Europe, the Middle East, Africa,
Korea, Thailand, Malaysia
4G (LTE-FDD): B1, B3, B7, B8, B20, B28A
3G: B1, B8
2G: B3, B8
RUT240 *5**** Japan
4G (LTE-FDD): B1, B3, B8, B18, B19, B26
4G (LTE-TDD): B41
3G: B1, B6, B8, B19
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.

10
DATASHEET // RUT240
MOUNTING OPTIONS
DIN RAIL KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
35mm DIN Rail
Low carbon steel
57g
Philips Pan Head screw #6-32×3/16, 2pcs
82 mm x 46 mm x 20 mm
V
DIN RAIL KIT
DIN Rail adapter
Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx
ORDER CODE HTS CODEHS CODE
PR5MEC00
For more information on all available packaging options – please contact us directly.
73269098 7326.90.98
SURFACE MOUNTING KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
Flat surface mount
ABS + PC plastic
2x5 g
Philips Pan Head screw #6-32×3/16, 2pcs
25 mm x 48 mm x 7.5 mm
V
DIN RAIL KIT
Surface mounting kit
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEHS CODE
PR5MEC12
For more information on all available packaging options – please contact us directly.
73269098 7326.90.98
COMPACT DIN RAIL KIT
Parameter
Mounting standard
Material
Weight
Screws included
Dimensions
RoHS Compliant
Value
35mm DIN Rail
ABS + PC plastic
6.5 g
Philips Pan Head screw #6-32×3/16, 2pcs
70 mm x 25 mm x 14,5 mm
V
DIN RAIL KIT
Compact plastic DIN Rail adapter (70x25x14,5mm)
Philips Pan Head screw #6-32×3/16, 2pcs
ORDER CODE HTS CODEHS CODE
PR5MEC11
For more information on all available packaging options – please contact us directly.
73269098 7326.90.98
Copyright © 2021, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.