Audiovox AUTO SECURITY Prestige OE3B4 Operating instructions

128-6505B
1 of 4
TRANSMITTER
PROGRAMMINGGUIDE
Model:OE3B4
The transmitters included with the security system have been pre-programmed
at the factory, with each button pre-assigned to control a specific function of the
security system. Although the security system in the vehicle has either a 3 or 4
channel receiver, depending on the model, the transmitters included with the
system are capable of transmitting 7 distinct signals. This allows you to program
each transmitter to more than one vehicle in two car families, and also allows you
to change which button(s) control certain functions of the system.
(Example: Transmitter channel 5 can be programmed to activate Receiver
channel 2.) Refer to the chart below for access to each of the transmitter channels,
and for the standard factory button assignments.
Some of the more common accessories for these additional channels are;
AS 9554 Remote Garage Door Interface
AS 9075 Remote car starter
AS 9153 Remote window roll up
AS 9256 Remote trunk release relay
TRANSMITTER SYSTEM RECEIVER
CHANNEL BUTTON CHANNEL FUNCTION
Remote Arm
1 1 Remote Emergency Panic
Remote Door Lock
Remote Disarm
2 2 Remote Emergency Panic
Remote Door Unlock/Unlock 2
3or 3
4& 4
5& 5
6 & 6 RF Channel For Options
7 7 RF Channel For Options
All 3
Buttons
Single Push Pulsed Output for Optional Accessory
Or Double Push For Additional Optional Accessory
Single Push Pulsed Output for Optional Accessory
Or Push And Hold For Extended Output
Single Push Pulsed Output for Optional Accessory
Or Push And Hold For Extended Output
Revision A: Added Pad # 73 for Circuit City Program
on last page
Revision B Added reference for PBLED 6/06

128-6505B
2 of 4
PROGRAMMINGTHE TRANSMITTERS: Itisimportant torememberthat duringprogram-
ming, each individual step of the procedure must be executed within 15 seconds of the
previous step. When the 15 second time limit is allowed to expire, the system will
automatically terminate the programming mode. This is indicated by a long chirp from the
siren and or vehicle's horn.NOTE: Some keyless entry systems will flash the interior light
to indicate a stored code. Substitute the words light flash below where indicated sounding
device will beep.
Additionally, the system will store codes from up to four different transmitters. If a 5th
transmitter is programmed to any receiver channel, then the first transmitter programmed
to that channel will be erased from the system's memory.
NOTE: Some Systems may include a Push-Button LED Switch instead of an individual
separate LED and Push-Button Switch
To Program replacement or additional transmitters:
1. Enter the vehicle, and turn the ignition key to the "on" position.
2.Press and release the valet push-button switch 3 times.
3.ThedashLED will flash one time, and thesounding device will beep one time, indicating
the system is ready to accept programming for receiver's Lock channel 1.
4.Press and hold the Lock transmitter button until the sounding device emits a long beep,
indicating the signal has been stored into memory.
5.If you have additional transmitters (up to 4) that need to be programmed, repeat step
4 for each transmitter.
Note: Single button programming units will operate your unit in the default factory mode
once the first button is programmed. If your unit is a single button programming unit
youcan exittheprogrammodeafter step5. Consult yourinstallation centerfor advise
on your system's transmitter programming method.
6.Press and release the valet push-button switch once.
7.ThedashLEDwillflashtwotimes,andthesoundingdevicewillbeeptwotimes,indicating
the system is ready to accept programming for receiver's Unlock channel 2.
8.PressandholdtheUnlocktransmitterbuttonuntilthesoundingdeviceemitsalongbeep,
indicating the signal has been stored into memory.
9.If you have additional transmitters (up to 4) that need to be programmed, repeat step
8 for each transmitter.
10. Press and release the valet push-button switch once.
11. The dash LED will flash three times, and the sounding device will beep three times,
indicating the system is ready to accept programming for receiver's channel 3.
12. Press and hold the selected Option/Trunk/Key transmitter button until the sounding
device emits a long beep, indicating the signal has been stored into memory.
13. Ifyouhave additional transmitters ( up to 4 ) thatneedto be programmed, repeat step
12 for each transmitter.
APS-55/APS-55LRA/PRO-9555a/PRO9556usesteps1-13only.
14. Press and release the valet push-button switch once.

128-6505B
3 of 4
15. The dash LED will flash four times, and the sounding device will beep four times,
indicating the system is ready to accept programming for receiver's channel 4.
16. Press and hold any button combination as shown on the front cover of this guide until
the sounding device emits a long beep, indicating the signal has been stored into
memory.
17. If you have additional transmitters (up to 4) that need to be programmed, repeat step
16 for each transmitter.
18. Press and release the valet push-button switch once.
19. The dash LED will flash four times, and the sounding device will beep four times,
indicating the system is ready to accept programming for receiver's channel 5.
20. Press and hold any unused button combination as shown on the front cover of this
guideuntilthesoundingdeviceemitsalongbeep,indicatingthesignalhasbeenstored
into memory.
21. If you have additional transmitters (up to 4) that need to be programmed, repeat step
20 for each transmitter.
NOTE: If the program switch is operated again, the circuit will recycle through the
program mode. In other words, press 1 time to access the lock function, 2 times to
access the unlock function, 3 times to access the start function. When programming
is complete simply turn off the ignition switch to exit the program mode.
22. Turnthe ignitionkey off.The soundingdevice willemit one shortbeep followedby one
long beep indicating the system has terminated the program mode.
TRANSMITTERBATTERYREPLACEMENT
You will notice a decrease in transmitter range as the battery condition deteriorates.
Transmitter battery replacement is recommended at least every 10 to 12 months,
depending upon how frequently the transmitter is used.
ThetransmitterhasasmallLEDvisiblethroughthecase.ThisLEDcanbeusedtoindicate
batterycondition. Ifthe LED doesnot illuminate,then the batteryis discharged,and must
bereplaced.
To replace the transmitter battery,
1. Remove the small phillips head screws from the
bottom cover of the transmitter.
2. Carefully unsnapthe topcover ofthe transmitterfrom
the bottom cover.
3. Remove the discharged battery, making note of the location of the + and - contacts,
and replace with a new type GP 27A 12 volt battery.
4. Replace the transmitter cover, taking care not to damage the LED or switches on the
circuit board, and secure with the small phillips head screw.

128-6505B
4 of 4
ORDER FORM FOR 3 BUTTON TRANSMITTER
MODEL NO. OE3B4
IMPORTANT: To help us expedite your order, please print all of the information legibly,
and mail this form and your payment according to the instructions below.
Note: Order Pad # 70 if your Lock & Unlock Icons are White
Order Pad # 71 if your Lock & Unlock Icons are Red.
Order Pad # 72 if you have a key icon on the large button
Order Pad # 73 if you have a trunk/key icon on the large button
Note: Transmitter model number found on back of case. ___________
1. Name : ____________________________________________________
Address: _____________________________________________________
City : _____________________ State : _______ Zip Code : ____________
2. Telephone Number : ( _______ ) _______________________________
3. Enter the total number of transmitters required here : ________________
4.List model number ofyour actual transmitter pad as shown on page 4 of this
manual: _________________________
5. The cost per transmitter is $ 65.00.
6. Enter the total amount enclosed here : ____________________________
(New York State residents must include the appropriate sales tax.)
7. Method of payment; check one of the boxes below.
!Mastercard !Visa !Check or money order * ( do not send cash )
* Make checks payable to Audiovox Corporation
8. Credit Card Number : ________________________________________
9. Credit Card Expiration Date : _____________________
Credit card purchasers can order additional or replacement
transmittersby phone. Simplydial 1- 800- 645- 4994and follow
the instructions from the operator interface.
10. Mail this form, and your check, to :
©2006AudiovoxElectronicsCorp.,150MarcusBlvd.,Hauppauge,NY,11788 128-6505B
Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y., 11788
Attn.:TRANSMITTERDEPARTMENT
"