Autonics PSQ Series User manual

G-9
PSQ Series
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
● Pressure measurement of any gas, liquid or oil [Fluid type]
(※except substances which may corrode stainless steel 316L)
● Simultaneous display of present value (PV) and set value (SV)
※Selectable SV, pressure unit, or none display for SV display part
● Selectable NPN, PNP open collector output by parameter setting
● 3 colors for PV display part (run mode: red or green / setting mode: orange)
● 12-segment LCD display for easier value reading
● Measurement range: -100.0 to 100.0kPa, -100 to 1,000kPa
(pneumatic type: compound pressure, uid type: sealed gauge pressure)
● Analog output: voltage (1-5VDC), current (DC4-20mA)
● Parameter copy function
● Option input/output: auto shift, remote zero, hold (only for PSQ- C U - )
● Forced output control mode for device testing and maintenance
● Min. display unit: 0.1kPa, 1kPa (variable by model)
● One-touch connector type for easy wiring and maintenance
● Password setting for SV
Compact, Dual LCD Display Digital Pressure Sensor
E.g.) For calculating 760mmHg to kPa : According to above chart, 1mmHg is 0.133322kPa,
therefore 760mmHg will be 760×0.133322kPa=101.32472kPa.
Features
Pressure Conversion Chart
to
from Pa kPa MPa kgf/cm2mmHg mmH2O psi bar inHg
1Pa 1 0.001 0.000001 0.000010197 0.007501 0.101972 0.000145038 0.00001 0.0002953
1kPa 1000.000 1 0.001 0.010197 7.500617 101.971626 0.145038 0.01 0.2953
1MPa 1000000 1000 1 10.197162 7500.61683 101971.626 145.038243 10 295.299875
1kgf/cm298066.5 98.0665 0.098067 1 735.55924 10000.0005 14.223393 0.980665 28.959025
1mmHg 133.322368 0.133322 0.000133 0.001359 1 13.595099 0.019337 0.001333 0.039370
1mmH2O 9.80665 0.009807
-
0.000099 0.073556 1 0.00142 0.000098 0.002896
1psi 6894.733 6.89473 0.006895 0.070307 51.714752 703.016716 1 0.068947 2.036014
1bar 100000.0 100.0000 0.100000 1.019716 750.062 10197.1626 14.503824 1 29.529988
1inHg 3386.388 3.386388 0.003386 0.034532 25.40022 345.315507 0.491156 0.033864 1
Pneumatic type
Fluid type
Ordering Information
Pressure port
Option Input/Output
Cable
Pressure range
Applicable fluid
Applicable fluid
Appearance
Item
Applied uid
Pressure port Pneumatic type Fluid type
Rc1/8
R1/8
NPT1/8
-
R1/4
-
NPT1/4
-
9/16-18UNF
-
No mark NPN or PNP open collector output
UNPN or PNP open collector output +
analog output or external input type
No mark Cable type
CConnector type
01 100kPa
11,000kPa
CCompound pressure
No mark Pneumatic type (air, non-corrosive gas)
BFluid type (gas, liquid, oil)
Q
Regular square type (30×30mm), dual display
PS Pressure Sensor
PS CQ 01 C Rc1/8
Please read “Safety Considerations”
in the instruction manual before using.

G-10
PSQ Series
Specifications
※( ) is Max. pressure display range. ※For using mmH2O unit, multiply display value by 100.
Type MPa kPa kgf/cm² bar psi mmHg inHg mmH2O
Compound
pressure
-
-100.0 to 100.0
(-101.3 to 110.0)
-1.020 to 1.020
(-1.033 to 1.122) -1.000 to 1.000 (-1.013 to 1.100) -14.50 to 14.50 (-14.70 to 15.95) -750 to 750 (-760.0 to 825.1) -29.5 to 29.5 (-29.91 to 32.48) -102.0 to 102.0 (-103.3 to112.2)
-
-100 to 1000
(-101 to 1100) -1.020 to 10.20 (-1.030 to 11.22) -1.000 to 10.00 (-1.01 to 11.00) -14.50 to 145.0 (-14.65 to 159.5) -750 to 7500 (-757.6 to 8251) -29.5 to 295 (-29.83 to 324.8) -102.0 to 1020 (-103.0 to 1122)
Pressure and Max. Pressure Display Range
Pressure type Gauge pressure (In case of uid type, standard pressure are sealed gauge pressure※1)
Type NPN or PNP open collector output type NPN or PNP open collector output+
analog output or external input type
Model PSQ- C01 - PSQ- C1 - PSQ- C01 U- PSQ- C1 U-
Rated pressure range -100.0 to 100.0kPa -100 to 1,000kPa -100.0 to 100.0kPa -100 to 1,000kPa
Display&Setting
pressure range -101.3 to 110.0kPa -101 to 1,100kPa -101.3 to 110.0kPa -101 to 1,100kPa
Min. display unit 0.1kPa 1kPa 0.1kPa 1kPa
Max.
pressure
range
Pneumatic type 2 times of rated pressure 1.5 times of rated pressure 2 times of rated pressure 1.5 times of rated pressure
Fluid type 3 times of rated pressure
Applied uid • Pneumatic type: air, non-corrosive gas
• Fluid type: air, non-corrosive gas and fluid that do not corrode stainless steel 316L
Power supply 12-24VDCᜡ (ripple P-P: max. 10%)
Allowable voltage range 90 to 110% of rated voltage
Current consumption Max. 50mA Max. 50mA (analog output: max. 70mA)
Control output NPN or PNP open collector output
Load voltage: max. 30VDCᜡ Load current: max. 100mA Residual voltage: max. 2VDCᜡ
Hysteresis※2Min. display interval
Repeat error ±0.2% F.S. ± min. display interval
Response time Select one; 2.5ms, 5ms, 10ms, 25ms, 50ms, 100ms, 250ms, 500ms, 1,000ms, 5,000ms
Protection circuit Output short over current protection circuit
Analog
output※3
Voltage
output
-
Output voltage: 1-5VDCᜡ ±2.5% F.S.
Linear: max. ±1% F.S.
Resolution: 1/2,000
Output impedance: approx. 240Ω
Response time: 50ms
Current
output
-
Output current: DC4-20mA ±2.5% F.S.
Linear: max. ±1% F.S.
Resolution: 1/2,000
Output impedance: approx. 100kΩ
Response time: 50ms
External input※3
(Auto shift/
Remote zero/Hold)
-
ON voltage: max. 0.4VDCᜡ
OFF voltage: 5-Vin or open
Resolution: 1/2,000
Output impedance: approx. 100kΩ
Display digits Present value (PV) display part, setting value (SV) display part: 4-digit
Display method 12-segment LCD method
Min.
display
interval
MPa 0.001 0.001 0.001 0.001
kPa 0.1 1 0.1 1
kgf/cm20.001 0.01 0.001 0.01
bar 0.001 0.01 0.001 0.01
psi 0.02 0.2 0.02 0.2
mmHg 1 - 1 -
inHg 0.1 - 0.1 -
mmH2O 0.1 - 0.1 -
Display accuracy 0 to 50℃: max. ±0.5% F.S., -10 to 0℃: max. ±1% F.S.
Insulation resistance Over 50MΩ (at 500VDC megger)
Dielectric strength 1,000VAC 50/60Hz for 1min
Vibration 1.5mm amplitude at frequency of 10 to 55Hz (for 1min) in each X, Y, Z direction for 2 hours
Environ-
ment
Ambient temp. -10 to 50℃, storage: -20 to 60℃
Ambient humi. 30 to 80%RH, storage: 30 to 80%RH
Cable (fluid type) Ø4mm, 5-wire, 3m (AWG24, core diameter: 0.08mm, number of cores: 40, insulator out diameter: Ø1mm)
Protection structure • Pneumatic type: IP40 (IEC standard) • Fluid type: IP65 (IEC standard)
Material • Pneumatic type - Front case: polycarbonate, rear case: polycarbonate, pressure port: brass-nickel plated
• Fluid type - Front case: polycarbonate, rear case: polyamide 6, pressure port: stainless steel 316L
Approval ,
Weight※4• Pneumatic type: approx. 165g (approx. 80g) • Fluid type: approx. 210g (approx. 125g)
※1: The unit is sealed structure. It is based on atmospheric pressure 101.3kPa.
※2: In hysteresis output mode, it is variable.
※3: Select one between analog output (voltage or current) and external input.
※4: The weight includes packaging. The weight in parenthesis is for unit only.
※For using mmH2O unit, multiply display value by 100.
※
Environment resistance is rated at no freezing or condensation.

G-11
Compact, Dual LCD Display Digital Pressure Sensor
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
Unit Description 1. Present value (PV) display part (green, red, orange by setting/status)
RUN mode: Displays PV.
Setting mode: Displays parameter.
2. Setting value (SV) display part (green)
RUN mode: Displays setting value, unit, etc.
Setting mode: Displays SV.
3. Output indicator (OUT1, OUT2) (orange): Turns ON while the control output turns ON.
4. Mkey
RUN mode: Press the M key for over 2 sec to enter parameter 1 group.
Press the M key for over 4 sec to enter parameter 2 group.
Setting mode: Press the M key to select the setting items.
Press the M key for over 2 sec to return RUN mode.
5. , key
RUN mode: Press the , key to set preset value of output operation mode.
Press the M+ keys to set key lock/unlock.
Press the + keys to adjust zero point.
Press the M+ keys to set peak hold.
Preset value setting mode: Press the , key to increase/decrease setting value.
Setting mode: Changes the parameter.
Dimensions
3
4 5
1
2
(unit: mm)
Accessory
Pneumatic type
R1/8 model 8mm
NPT1/8 model
※A
20
12 20
2-M3
30
32.7
24.8 7.9
Rc(PT)1/8"
Fluid type
R1/8 model (standard) 8mm
Rc1/8 model 0mm
R1/4 model 11.5mm
NPT1/4 model
9/16-18UNF model
(metal gasket sealing method)
15.4mm
※A
30
30
33.5
30 12.3 A
Inside
M5 Tap
Ø4, 3m
17
32.7
24.8 7.9 A
Inside M5 Tab
20 2-M3
20
Connector cable (PSO-C01, Pneumatic/Fluid type)
※Ø4mm, 5-wire, 2m
( AWG24, core diameter: 0.08mm,
number of cores: 40,
insulator diameter: Ø1mm)

G-12
PSQ Series
Dimensions
Accessory
Bracket A (Pneumatic type)
20
20
30
20
40
45
15
4.2
1.6
13
3-Ø3.2
Ø4.2
Bracket C (Fluid type)
4-Ø3.2
Ø22 20
20
40
36
55
15
22
3.5
4.2
30
Bracket B (Pneumatic type)
25
35 Ø4.2
4.2
6
22
20
40
45
3-Ø3.2
20
30
1.6
(unit: mm)
(panel thickness 0.8 to 3.5mm)
36
+0.5
0
( panel thickness: 0.5 to 7mm)
31
0
-0.4
<When 'N' units are installed in series>
31
0
-0.4
31×N+3.5×(N-1)
Min. 55
Integrated installation set (Pneumatic/Fluid type)
Separate installation set (Pneumatic type)
28.2
40
30
40
42 35 26
3
20
25.8
<Rear panel bracket><Front panel bracket>
Front cover (PSO-P01)
Front cover (PSO-P02)
Panel cut-out
Front/Rear pael bracket set (PSO-B04)
Panel bracket (PSO-B02) Panel cut-out
6.75
7
37
41
34.2
42
39.8
34.2
34.2
9
9
16.9
34.4
30.5
3
Sold separately
42
9.7
40
40
5.7
1
M5 gender (PSO-Z01, Pneumatic type)

G-13
Compact, Dual LCD Display Digital Pressure Sensor
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
Input/Output Circuit and Connections
NPN open collector output type
NPN open collector output+
analog output or external input type
PNP open collector output+
analog output or external input type
PNP open collector output type
Setting for Each Mode
Main circuit
Main circuit
Output short
over current
protection circuit
Load
Main circuit
(brown) +V
(blue) 0V
(black) OUT1
(white) OUT2
12-24VDC
Output short
over current
protection circuit
Load
(brown) +V
(blue) 0V
(black) OUT1
(white) OUT2
12-24VDC
Load
Load
※ : output impedance ※ : output impedance
(brown) +V
(blue) 0V
(black) OUT1
(white) OUT2
12-24VDC
(orange) analog output/
external input
Load
Load
(brown) +V
(blue) 0V
(black) OUT1
(white) OUT2
12-24VDC
(orange) analog output/
external input
Load
Load
RUN
mode
Preset value settingZero-point adjustment
Parameter 2 groupKey lock
High/Low peak hold
,
+for over 1 sec
※It sets reference pressure to the current
atmospheric pressure as zero.
for over 1 sec
for over 1 sec
Output short
over current
protection circuit
Output short
over current
protection circuit
Output short
over current
protection circuit
Output short
over current
protection circuit
Main circuit
Output short
over current
protection circuit
Output short
over current
protection circuit
Zero-point Adjustment
1. To set zero atmospheric pressure forcibly, press the + keys over 1 sec in RUN mode with the opened pressure port.
2. Zero point adjustment is completed, the PV display part displays )0.
※Please execute zero-point adjustment regularly.
※
If executing zero-point adjustment
when external pressure over ±5% of
rated pressure is applied, ERR1 ashes
ve times during pressing the keys.
Remove external pressure and
execute zero point again.
for over 4 sec
M
for over 2 sec
M
Parameter 1 group
for over 2 sec
M
M
M+
M+
Press over 1 sec
1 2
M

G-14
PSQ Series
Parameter Setting
※After entering parameter 1/2 group, if there is no additional key input for 60 sec, it maintains previous setting value and it returns to RUN mode.
※Press the , key to set the setting value.
※After entering parameter 1/2 group, press the M key for over 2 sec to return to RUN mode.
※When pressing the M key once returning RUN mode from parameter 1 group, 2 group within 2 sec, it enters the previous parameter group.
※Some parameters are activated/deactivated according to the setting of other parameters. Refer to the description of each parameter.
Parameter Group
Parameter 1 group
Parameter name Setting range Description
Factory
default
OUT1 OUT1 operation
mode
EASY
HYsM
WIN
AUTO
fOUT
Easy
Hysteresis
Window comparison
Auto sensitivity setting
Forced output control
Select OUT1 operation mode.
※
When setting OUT1 operation mode as auto sensitivity setting mode [AUTO] or
forced output control mode [fOUT], OUT2 operation mode is set automatically
same as the setting value of OUT1 operation mode.
EASY
OUT2 OUT2 operation
mode
OFF
EASY
HYsM
WIN
OFF
Easy
Hysteresis
Window comparison
Select OUT2 operation mode. OFF
I/O※1Analog output/
External input
A-V
A-C
SHFT
ZERO
HOLD
Analog voltage output
Analog current output
Auto shift
Remote zero
Hold
Select analog output/external input operation mode.
Auto shift: When reference pressure of the pressure sensor changes, It
corrects present pressure to reference pressure and by moving
detection level as much as fluctuation level.
Remote zero: I t is the same function as auto shift but remote zero
makes the measured pressure as 0 forcibly.
Hold: The function to hold present value (PV) and control output while
signal is input.
※
When OUT1 operation mode is set as [fOUT] or applied pressure
is higher/lower than the display pressure range, auto shift [SHFT],
remote zero [ZERO] functions are not available.
A-V
ShOT※1Auto shift
applied terminal
OUT1
OUT2
ALL
OUT1
OUT2
OUT1 & OUT2
Select auto shift applied terminal.
※
Appears when Analog output/External input is [SHFT]. OUT1
ZeOT※1Remote zero
applied terminal
OUT1
OUT2
ALL
OUT1
OUT2
OUT1 & OUT2
Select remote zero applied terminal.
※
Appears when analog output/external input is [ZERO]. OUT1
NoNC Output type
OUT1 OUT2
NO
Normally Open OFF
※
Appears when OUT2 operation mode is [OFF].
NC
Normally Closed OFF
1O2O
Normally Open Normally Open
※
Appears when OUT1 operation mode is [AUTO],
or OUT2 operation mode is [HYsM], [WIN].
1O2C
Normally Closed Normally Open
1C2O
Normally Closed Normally Open
1C2C
Normally Closed Normally Closed
NO
SPD Response time @5,5,10,25,50,100,250,
500,1000,5000
It can prevent control output from chattering by changing response time.
※ If the response time is getting longer, the detection will be more stable
but present value (PV) might be different from the real pressure
value.
@5
CLOR PV display color
R-ON
G-ON
RED
GREN
Normal: Green / Output: Red
Normal: Red / Output: Green
Fixed red
Fixed green
Select the present value (PV) display and the color linked output. R-ON
DISP Color linked
output
OUT1
OUT2
ALL
OUT1
OUT2
OUT1 & OUT2
Select the color linked output.
※ Appears when OUT2 operation mode is not [OFF] and PV display color
is set as [R-ON] and [G-ON].
OUT1
UNIT Display unit
KPA
MPA
KGF
BAR
PSI
MMHG
INHG
H2O
kPa
MPa
kgf/cm2
bar
psi
mmHg
inHg
mmH2O
Select the display unit.
※
For using mmH2O unit, multiply display value by 100. KPA
※1: Appears only in NPN or PNP open collector output + analog output or external input model.

G-15
Compact, Dual LCD Display Digital Pressure Sensor
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
Parameter Setting
Parameter 2 group
Parameter name Setting range Description
Factory
default
SUB SV display part
STD
UNIT
OFF
Standard
Unit
OFF
Select the display type at the SV display part in RUN mode.
Standard [STD]: Display setting value (SV) always.
Unit [UNIT]: Display pressure unit normally. When pressing , key,
display setting value (SV) for 5 sec.
None [OFF]: It does not display any value normally. When pressing ,
key, display setting value (SV) for 5 sec.
※ If select unit [UNIT] or None [OFF], changing setting value (SV) is
available when setting value is displayed.
STD
COPY Parameter copy
OFF
ON
ON-L
OFF
ON
ON with key lock
This function is for copying parameter settings of Master to Slave 1:1.
※ For the details, refer to '▣ Functions - ◎ Paprameter Copy'. OFF
INIT Parameter reset OFF
ON
OFF
Reset parameter setting
Reset the parameter settings. OFF
PWD Password
0000
to
9999
-
Set the 4-digit password.
[0000]: Disable password
[0001]: Only checking parameters
0000
sOUT Control output
switching
NPN
PNP
NPN
PNP Select type of control output. NPN
HYS Hysteresis for
easy mode
1
to
11111111
Bar type
(Min: 1ea , Max: 8ea)
Set the hysteresis for easy mode.
Rated pressure range Hysteresis per 1 Bar
-100.0 to 100.0kPa 0.1kPa
-100.0 to 1,000kPa 1kPa
※ Appears when OUT1 or OUT2 operation mode is easy mode.
※ Although the display unit is changed, standard unit of hysteresis for
easy mode is not changed.
111
High/Low Peak Hold
※Clearing Max./Min. pressure value.
1. Press the M+ key for over 1 sec in RUN mode
and set the peak hold.
2. High peak is displayed on present value (PV)
display, and low peak is displayed on setting value
(SV) display.
3. Press the + key for over 1 sec, initialize high/
low peak value.
Clearing Max./Min. pressure value
Retained maximum and minimum
pressure value will flash every 0.5 sec
M+
for over 1 sec +
for over 1 sec
※When the memorized Max. pressure is higher
than the rated pressure, it displays HHHH.
When it is lower than the rated pressure,
it displays LLLL.
Analog Output Scale Adjustment
only for NPN or PNP open collector output+analog output or external input type model
Output
PV
A-04 A-20
20mA
21.6mA
4mA
2.4mA
10%
F.S.
10%
F.S.
Output
PV
A-1V A-5V
5VDC
5.4VDC
1VDC
0.6VDC
10%
F.S.
10%
F.S.
This function is to diagnose malfunction of the system caused by parasitic pressure through memorizing input the max./min. pressure
occurred from the system.
M

G-16
PSQ Series
Preset Setting
● NPN or PNP open collector output(OUT1/2)
1. Select OUT1/2 operation mode [OUT1/2] to use in parameter 1
group.
( OUT1/2 operation mode: easy, hysteresis, window comparison, auto
sensitivity setting, forced output control)
2. Enter the preset setting mode from RUN mode.
( set items are displayed in the order of OUT1 - OUT2)
3. Set the value for each item.
●Analog output/External input
1. Select analog output/extenal input mode [I/O] to use in
parameter 1 group.
( Analog output/extenal input: analog voltage output, analog current
output, auto Shift, remote zero, hold)
2. Enter the preset setting mode from RUN mode.
( analog output/external input items are displayed after OUT1 -
OUT2)
3. Set the value for each item.
Setting guide
To enter the preset setting mode, press the , key in RUN mode.
Press the , key to change preset value, the M key to move to the next mode.
If there is no additional key or the M key input for over 2 sec during setting, the value is automatically set and it returns to RUN mode. (except
forced output control mode)
●Note
Setting items and setting value are displayed at the setting value (SV) display part alternatively.
Operation mode (easy, hysteresis, window comparison, auto sensitivity setting) that can be set separately per each output (OUT1/OUT2)
display parameter name with identification number.([
ST
]: [
ST1
]/[
ST2
])
When changing pressure unit or analog output/extenal input, the preset value is initialized corresponding to changed item.
When changing operation mode, the preset value is reset for the changed mode.
●Preset setting by output operation mode
Output
operation
mode
Preset Setting range
Factory default
-100.0 to
100.0kPa
-100 to
1,000kPa
EASY Easy PPressure detection
level
Min. display pressure＜[P] ≤ Max. display pressure
05)0 0500
HYsM
Hysteresis
ST Pressure detection
level
Min. display pressure＜[ST] ≤ Max. display pressure
05)0 0500
HYS Hysteresis level
Min. display pressure ≤ [HYS]＜[ST]
-5)0 0000
WIN
Window com-
parison
LO
Pressure detection
level low-limit
Min. display pressure ≤ [LO] ≤ Max. display pressure
- (3 × min. display unit)
-5)0 0000
HI
Pressure detection
level high-limit
[LO] + (3 × min. display unit) ≤ [HI] ≤ Max. display pressure
05)0 0500
AUTO Auto sensitivity
setting
ST1
Pressure detection
level 1
Min. display pressure ≤ [ST1] ≤ Max. display pressure
- 1% of rated pressure
-5)0 0000
ST2
Pressure detection
level 2
[ST1] + 1% of rated pressure ≤ [ST2] ≤ Max. display pressure
05)0 0500
SET
Pressure detection
level
SET
=(ST1+ST2)
2
, [
ST1
] ≤ [
SET
] ≤ [
ST2
]
Pressure detection level [SET] can be selectable by pressing
the , key.
00)0 0250
fOUT Forced output
control
- - - - -
A-V Analog voltage
output
A-1V 1V output SV 0% F.S. ≤ [A-1V] ≤ 100% F.S. `0)0 0000
A-5V 5V output SV [A-1V] + 10% F.S. ≤ [A-5V] ≤ 100% F.S. or
0% F.S.≤ [A-5V] ≤ [A-1V] - 10% F.S. 10)0 1000
A-C Analog current
output
A-04 4mA output SV 0% F.S. ≤ [A-04] ≤ 100% F.S. `0)0 0000
A-20 20mA output SV [A-04] + 10% F.S. ≤ [A-20] ≤ 100% F.S. or
0% F.S. ≤ [A-20] ≤ [A-04] - 10% F.S. 10)0 1000
Setting example
OUT1: Hysteresis mode
OUT2: Window comparison mode
Run mode
M for over
2 sec
05)0
HI2
Pressure
detection level 2
low-limit value
Pressure
detection level 2
high-limit value
LO2 -5)0
Hysteresis
level 1 -5)0
HYS1
Pressure
detection
level 1
ST1 05)0 OUT1:
Hysteresis
mode
OUT2:
Window
comparison
mode
,
M
M
M
4mA
output
SV
20mA
output
SV
OUT1, OUT2 Preset setting
A-04 `0)0
10)0
A-20
Setting example
Analog current output scale
M
M
M

G-17
Compact, Dual LCD Display Digital Pressure Sensor
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
Hysteresis mode [HYsM]
Set the hysteresis of pressure detection.
Set the pressure detection level [ST1, ST2] and hysteresis [HYS1, HYS2].
ST2
HYS2
ST1
HYS1
Time
Time
Time
Time
Time
Pressure
h
h
ST2/ HYS2
ST1/ HYS1
ST1/ HYS1
ST2/ HYS2
OUT1 N.O. ON
OFF
ON
OFF
ON
OFF
ON
OFF
OUT2 N.O.
OUT1 N.C.
OUT2 N.C.
Preset Setting
Supported operation mode list
NPN or PNP open collector output
OUT1 OUT2
EASY Easy
OFF OFF
EASY Easy
HYsM Hysteresis
WIN Window comparison
HYsM Hysteresis
OFF OFF
EASY Easy
HYsM Hysteresis
WIN Window comparison
WIN Window comparison
OFF OFF
EASY Easy
HYsM Hysteresis
WIN Window comparison
AUTO Auto sensitivity setting
fOUT Forced output control
※
Analog output (voltage or current) and external input (auto
shift/remote zero/hold) are not available at the same time.
Analog output※
A-V Analog voltage output
A-C Analog current output
External input※
SHFT Auto shift
ZERO Remote zero
HOLD Hold
●Preset setting by external input mode
External input mode Preset Setting range Factory
default
SHFT Auto shift ShIN Auto shift
correction value※
Min. preset setting value
＜
[ShIN]
＜
Max. preset setting value 00)0
ZERO Remote zero ZeIN Remote zero
correction value※
Min. preset setting value
＜
[ZeIN]
＜
Max. preset setting value 00)0
HOLD Hold
- - - -
※Apply 0VDC to orange cable over 1ms to operate auto shift or remote zero mode.
※ Press the + for over 1 sec to delete set auto shift correction.
Easy mode [EASY]
Set the hysteresis of pressure detection automatically.
Set the pressure detection level [P1, P2].
P2
HYS
P1
HYS
Time
Pressure
Time
Time
Time
Time
P2
P1
P2
P1
OUT1 N.O. ON
OFF
ON
OFF
ON
OFF
ON
OFF
OUT2 N.O.
OUT1 N.C.
OUT2 N.C.
※It is possible to set the hysteresis value in hysteresis for easy
mode of parameter 2 group.
Output Operation Mode
※PSQ Series has 5 output operation mode. Use the proper operation mode in accordance with the desired
application of detection.

G-18
PSQ Series
Output Operation Mode
Window comparison output mode [WIN]
It detects pressure at the desired range.
Set high-limit value of pressure detection level [HI1, HI2], and
low-limit value of pressure detection level [LO1,LO2].
Hysteresis is fixed as Min. display interval.
Time
Time
Time
Time
Time
Pressure
ON
OFF
ON
OFF
ON
OFF
ON
OFF
※1: Min. display interval
※1
※1
※1
※1
HI2
HI1
LO2
LO1
LO1/ HI1
LO1/ HI1
LO2/ HI2
LO2/ HI2
OUT1 N.O.
OUT2 N.O.
OUT1 N.C.
OUT2 N.C.
Auto sensitivity setting mode [AUTO]
It sets the proper detection sensitivity automatically.
It sets by the two pressure points [ST1, ST2].
Hysteresis is fixed as Min. display interval.
The pressure detection level [SET] is shown in the below formula.
(ST1 +ST2)
2
SET
=
Pressure ※1: Min. display interval
※1
※1
※1
ST1/ ST2
SET
SET
ST1/ ST2
OUT1 N.O.
OUT2 N.O.
OUT1 N.C.
OUT2 N.C.
ST2
SET
ST1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Time
Time
Time
Time
Time
Forced output control mode [fOUT]
RUN mode
fOUT
Regardless of setting value, it maintains comparison output OFF
and displays present pressure.
Set OUT1 operation mode [OUT1] of parameter 1 group as
[fOUT] and return to RUN mode. The PV display part displays the
measured pressure and the SV display part displays [fOUT].
During forced output control mode, press the or key to turn
ON/OFF OUT1, 2 manually.
RUN mode
RUN modeRUN mode Forced output
control mode
OUT1
OUT2
Time
ON
OFF
ON
OFF
M M
Time
M
M