Autronica AutroGuard V-430 Release Note

utronica Fire And Security AS

Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
COPYRIGHT ©
This publication, or parts thereof, may
not be reproduced in any form, by any
method, for any purpose.
Autronica Fire and Security AS and its
subsidiaries assume no responsibility
for any errors that may appear in the
publication, or for damages arising from
the information in it. No information in
this publication should be regarded as a
warranty made by Autronica Fire and
Security AS. The information in this
publication may be updated without
notice.
Product names mentioned in this
publication may be trademarks. They
are used only for identification.
E-1676
This product contains static-sensitive devices. Avoid any electrostatic discharge.
The WEEE Directive
When the marking below is shown on the
product and/or its literature, it means that
the product should not be disposed with
other household wastes at the end of its
life cycle. During waste treatment, disposal
and collection, please separate the
product from other types of wastes and
recycle it responsibly to promote the
sustainable reuse of material resources.
This product should not be mixed with
other commercial wastes for disposal.

Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Table of Contents
1. Introduction......................................................................1
1.1 Scope ................................................................................................1
1.2 The Manual .......................................................................................1
1.3 Target Audience................................................................................1
1.4 Reference Documentation.................................................................1
1.5 Downloading Technical Documents..................................................1
1.6 Technical Terms and Abbreviations..................................................2
1.7 Document Revision Log....................................................................3
2. Safety................................................................................4
2.1 Important Safety Information.............................................................4
2.2 Intended Use.....................................................................................5
2.3 Safety Notice.....................................................................................5
2.4 Safety Regulations............................................................................5
2.4.1 National Standards and Regulations ......................................5
2.4.2 Mounting, Installation, Commissioning and Maintenance.......6
2.4.3 Modifications to the products ..................................................6
2.5 Compliance with Standards and Directives.......................................6
2.6 Environment Compatibility.................................................................7
2.6.1 Recycling.................................................................................7
2.6.2 Disposal ..................................................................................7
3. Protector Overview..........................................................8
3.1 Product Decription.............................................................................8
3.2 Series / Variants................................................................................9
3.2.1 Protector Variants Without Integrated Alarm Devices ............9
3.2.2 Protector Variants With Integrated Alarm Devices .................10
3.3 Details for Ordering ...........................................................................11
3.3.1 Ordering Information V-430 ....................................................11
3.3.2 Ordering Information V-530 ....................................................12
3.3.3 Ordering Information V-100 ....................................................13
3.3.4 Ordering Information V-110/V-120..........................................13
3.3.5 Ordering Information Accessories...........................................13
3.4 Labeling.............................................................................................14
3.4.1 Marking on Protector (bottom)................................................15
3.4.2 Marking on Protector Base (inside).........................................16
3.4.3 Marking on Protector Top, EX only.........................................17
3.5 QR code and Data Matrix Code........................................................18
3.5.1 QR and Data Matrix Code Information....................................18
3.5.2 QR Code Placement on Protector ..........................................18
3.5.3 Data Matrix Code Placement on Protector Base’s
Tagholder................................................................................19
3.6 Tag Holder for Labels........................................................................19
3.7 Dimensions and Outlines ..................................................................20
3.7.1 Protector Base ........................................................................20
3.7.2 Protector with Visual Alarm Device (VAD)..............................20
3.7.3 Protector without Visual Alarm Device (VAD).........................21
3.7.4 Protector for Retrofit Mounting onto BWA-100/BWA-101
(Height) ...................................................................................21

Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security AS
Page 2
4. Technical Specifications.................................................22
4.1 Protector and Base............................................................................22
4.2 Integrated Sounder............................................................................23
4.3 Tones.................................................................................................23
4.4 Sound Pressure Levels for Tones.....................................................24
4.5 Integrated VAD..................................................................................28
5. Functional Description....................................................29
5.1 General..............................................................................................29
5.2 Chamber Design ...............................................................................29
5.3 DYFI3D ...............................................................................................30
5.3.1 DYFI3D - Particle/Smoke Signature Analysis ..........................30
5.3.2 DYFI3D - Dynamic Filtering......................................................31
5.4 Sensitivity Classes for Environmental Adaptivity ..............................32
5.5 Operation Classes.............................................................................32
5.6 Heat Response Categories...............................................................33
5.7 SelfVerify® 2.0 Function ...................................................................34
5.8 Cover Detection.................................................................................34
5.9 Protector “Alive Signal”......................................................................35
5.10 LED Behavior ....................................................................................35
6. Visual Alarm Device (VAD)..............................................36
6.1 Compliance with EN54-23.................................................................36
6.2 Coverage Volume..............................................................................36
6.3 Category C –Ceiling Mounted Devices............................................37
6.4 Category O........................................................................................38
6.5 Visual Alarm Device (VAD) Intensity.................................................38
6.5.1 Consideration Factors for VAD Sensitivity Settings................38
6.5.2 VAD Intensity Settings ............................................................38
6.5.3 VAD Intensity - White VAD and Red VAD ..............................39
6.6 Flash Rate.........................................................................................39
7. Audible Alarm Devices....................................................40
7.1 General..............................................................................................40
7.2 Sound Pressure Level.......................................................................40
7.3 Sound and Pulse Patterns.................................................................40
8. Planning ...........................................................................41
8.1 Reference to National/Local Regulations..........................................41
8.2 Enviromental Requirements..............................................................41
8.2.1 Location / Required Space......................................................41
8.3 Area Coverage and Monitoring Distance ..........................................42
8.3.1 Smoke Detection.....................................................................42
8.3.2 Heat Detection ........................................................................43
8.4 Current Consumption on Detection Loop..........................................44

Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
9. Mounting Instructions .....................................................45
9.1 Cable Entries/Exits on the Protector Base........................................45
9.1.1 Cable Entry for Concealed Conduit Wiring.............................45
9.1.2 Cable Entries/Knockout Stampings for Surface-mounted
Wiring......................................................................................46
9.2 Mounting the Protector Base.............................................................47
9.2.1 Considerations Before Mounting.............................................47
9.2.2 Template for Marking and Drilling Holes.................................48
9.2.3 Mounting for Concealed Conduit Wiring.................................49
9.2.4 Mounting onto a Ceiling Box / Wall Box..................................50
9.2.5 Mounting onto a Conduit Box..................................................51
9.2.6 Mounting for Surface-mounted Wiring....................................52
9.3 Connecting Loop Cables...................................................................53
9.3.1 Cable Requirements ...............................................................53
9.3.2 Wire Routing Arrangement Inside Protector Base..................54
9.3.3 Wire Insulation Stripping.........................................................55
9.3.4 Spring Cage Connection.........................................................56
9.3.5 Connections - Overview..........................................................57
9.3.6 Loop Connections...................................................................57
9.3.7 LED Connection......................................................................58
9.3.8 Branch-offs..............................................................................58
9.4 Alignment Marks on the Protector.....................................................60
9.5 Mounting the Protector onto the base...............................................61
9.6 Locking/Unlocking the Protector to the Base ....................................62
9.7 Removing the Protector from the Base.............................................63
9.8 Retrofit mounting onto Existing AutroSafe Base
BWA-100/BWA-101...........................................................................63
9.9 Labeling the Protector Base / Tag Holder.........................................64
9.10 Protector Cover .................................................................................64
10.Configuration...................................................................65
10.1 Introduction........................................................................................65
10.2 Configuration - AutroSafe..................................................................65
10.3 Site Configuration System Settings...................................................66
10.3.1Detector Defaults –LED on Alarm/LED Alive Blink................66
10.3.2Sound and Pulse Patterns ......................................................67
10.4 Adding System Units.........................................................................68
10.5 AutroGuard Default Settings .............................................................70
10.5.1Set AutroGuard Defaults Menu...............................................70
10.5.2Multi.........................................................................................71
10.5.3Ex............................................................................................71
10.5.4Ex/S.........................................................................................72
10.5.5Sounder...................................................................................72
10.5.6Visual Alarm Device (VAD).....................................................73
10.5.7Postfix .....................................................................................73
10.6 AutroGuard Individual Settings .........................................................74
10.6.1Fire Alarm Devices..................................................................74
10.6.2Automatic Test Mode..............................................................74
10.6.3Cover Detection Sensitivity.....................................................75
10.6.4Heat Response Categories.....................................................75
10.6.5Operation Classes...................................................................76
10.6.6Sensitivity Settings for Environmental Adaptivity....................76
10.6.7Visual Alarm Device (VAD).....................................................77
10.6.8Sound Pressure Level - Sounders..........................................79
10.7 Matching Protectors/Bases with AutroSafe Configurations ..............80

Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security AS
Page 4
11.Testing and Maintenance................................................81
11.1 SelfVerify® 2.0 Function ...................................................................81
11.2 Visual Inspection ...............................................................................81
11.3 Manual Testing..................................................................................82
11.3.1Introduction .............................................................................82
11.3.2Test Equipment.......................................................................82
11.3.3Automatic Test Mode..............................................................82
11.4 Cleaning Procedure...........................................................................83
11.5 Replacing a Protector (Hot Swap).....................................................83
12.Accessories .....................................................................84
12.1 Locking Tool for Locking the Protector to the Base ..........................84
12.2 QR Code Reader...............................................................................84
12.3 WAS-2000 and AS2000 Loop Diagnostic Tool.................................85
12.4 Cover.................................................................................................85
12.5 Air Duct Sampling Unit......................................................................86
12.6 Air Duct Sampling Unit –Stainless Steel..........................................87
12.7 Conduit Box.......................................................................................88
12.8 Telescope Removal Tool...................................................................89
12.9 Ground Device ..................................................................................89
12.10 Test Gas............................................................................................89
12.11 Testfire / Solo 365 Test Tool.............................................................90
13.Index.................................................................................91

Introduction
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 1
1. Introduction
1.1 Scope
This handbook provides all relevant technical information for the
AutroGuard® Multicriteria Protector, including a desciption of all
variants, technical specifications, functionality, planning, mounting,
configuration, plus testing and maintenance.
1.2 The Manual
Ensure that this Technical Handbook is read and understood before
installing/operating/maintaining the equipment. Pay attention to the
Safety Instructions. Instructions are listed in chapter 2 and repeated
where appropriate in this Technical Handbook.
1.3 Target Audience
The handbook is intended to be used by project engineers and
qualified service and technical personnel who are responsible for the
installation, commissioning and maintenance of the protector. It is
also useful for sales personnel.
1.4 Reference Documentation
The table below shows an overview of the technical documentation
for the protector.
Document Name
Part number
AutroGuard-V430-datasheet, English
Doc-1004268
AutroGuard-V530-datasheet, English
Doc-1004269
AutroGuard-V100-datasheet, English
Doc-1004270
AutroGuard-V110-120-datasheet, English
Doc-1004271
AutroGuard-technical-handbook, English
Doc-1004339
AutroGuard-sound-pressure-levels, English
Doc-1004281
1.5 Downloading Technical Documents
All relevant technical documents can be downloaded from the
Autronica product web at www.product.autronicafire.com/products

Introduction
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 2
1.6 Technical Terms and Abbreviations
The following technical terms are specifically related to the
AutroGuard® Multicriteria Protector.
Term
Explanation
FAD
Fire Alarm Devices include visual or audible alarm devices
(sounders)
FPE
Fire Protection Eqiupment. Fire control or fighting equipment,
e.g. extinguishing installation.
VAD
Visual Alarm Device (beacon, flash)
Sounder
An audible alarm device
Coverage Volume
With reference to EN54-23, the AutroGuard® Multicriteria
Protector features two categories in respect to Coverage Volume:
C, ceiling mounted devices
O, open class devices
Refer to chapter 6.2 for more detailed information.
VAD Intensity
The AutroGuard® protector’s integrated VAD can be configured
to have different intensities in order to meet the required
illumination at the premises. The AutroGuard® protector’s VAD
emits a white or red light and different VAD intensities (low,
medium, high and open) can be configured (with reference to
Coverage Volume).
Flash Rate
Measured in Hz. 1Hz flash rate is equal to one flash every second.
0,5Hz flash rate is equal to one flash every two seconds.
Cover Detection
An add-on feature to the AutroGuard® Multicriteria Protector. If
a dust cap or any other object covers the air inlet, a fault message
will appear. Refer to chapter 5.8 for more detailed information.
Sensitivity Classes
The AutroGuard® Multicriteria Protector can be programmed to
high, medium and low sensitivity classes for use in different
environments.
Heat Response Categories
Heat Response Categories (Heat Classes) apply to AutroGuard®
Multicriteria Protectors with Operation Classes Multi and Heat
only.
Protector head
The protector head for the AutroGuard® Multicriteria Protector
contains the housing, the detection chamber, all sensors,
audible/visible devices, printed circuit board and the rotatable
bajonet ring.
Protector base
The protector base (socket) for the AutroGuard® Multicriteria
Protector, containing a connector for detection loop cables,
circuit board, microcontroller.
Bajonet ring
Rotatable bajonet ring on the protector head used to easily
connect the protector to the base.

Introduction
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 3
1.7 Document Revision Log
Revision
Date
Description
Revision 1
2020-06-29
Officially approved by Autronica Fire and Security AS

Safety
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 4
2. Safety
2.1 Important Safety Information
IMPORTANT SAFETY INFORMATION. READ ENCLOSED WARNINGS
AND SAFETY INFORMATION.
THIS MANUAL CONTAINS PRODUCT SAFETY WARNINGS, WARRANTY
DISCLAIMERS, LIMITATIONS OF LIABILITY
PRODUCT WARNINGS
THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION
BY, AN EXPERIENCED PROFESSIONAL. AUTRONICA FIRE AND
SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR
ENTITY BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL FIRE RELATED PRODUCTS.
A PROPERLY INSTALLED AND MAINTAINED PRODUCT/SYSTEM MAY
ONLY REDUCE THE RISK OF EVENTS SUCH AS FIRE, SMOKE; IT IS NOT
INSURANCE OR A GUARANTEE THAT SUCH EVENTS WILL NOT OCCUR,
THAT ADEQUATE WARNING OR PROTECTION WILL BE PROVIDED, OR
THAT THERE WILL BE NO DEATH, PERSONAL INJURY, AND/OR
PROPERTY DAMAGE AS A RESULT.
AUTRONICA FIRE AND SECURITY
BATTERY OPERATED SENSORS, DETECTORS AND PANEL ACCESSORIES
HAVE A LIMITED BATTERY LIFE. WHILE THESE PRODUCTS ARE
DESIGNED TO PROVIDE SOME WARNING OF IMMINENT BATTERY
DEPLETION THE ABILITY TO DELIVER SUCH WARNINGS IS LIMITED
AND SUCH WARNINGS MAY NOT BE PROVIDED IN ALL
CIRCUMSTANCES. PERIODIC TESTING OF THE SYSTEM IN ACCORANCE
WITH THE INSTRUCTIONS PROVIDED IN THE USER MANUAL IS THE
ONLY WAY TO ENSURE ALL SENSORS, DETECTORS AND PANEL
ACCESSORIES ARE FUNCTIONING PROPERLY.

Safety
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 5
WARRANTY DISCLAIMERS
TO THE MAXIMUM EXTENT PERMITTED BY LAW, AUTRONICA FIRE
AND SECURITY HEREBY DISCLAIMS ALL WARRANTIES AND
REPRESENTATIONS, WHETHER EXPRESS, IMPLIED, STATUTORY OR
OTHERWISE INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH
RESPECT TO ITS PRODUCTS AND RELATED SOFTWARE. AUTRONICA
FIRE AND SECURITY FURTHER DISCLAIMS ANY OTHER IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS.
AUTRONICA FIRE AND SECURITY MAKES NO REPRESENTATION,
WARRANTY, COVENANT OR PROMISE THAT ITS PRODUCTS AND/OR
RELATED SOFTWARE (I) WILL NOT BE HACKED, COMPROMISED
AND/OR CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE
ADEQUATE WARNING OR PROTECTION FROM, FIRE , SMOKE; OR (III)
WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS.
2.2 Intended Use
The protector is intended for use in Autronica fire detection systems
and with the environmental conditions described in this handbook.
2.3 Safety Notice
Throughout this handbook you will find safety notices for the
purpose of notifying important installation, operation, or
maintenance information that is NOT HAZARD RELATED.
2.4 Safety Regulations
2.4.1 National Standards and Regulations
Products from Autronica Fire and Security are developed and
manufactured in compliance with international safety standards. Any
additional national or local safety standards that apply where the
equipment is installed and operated, must also be taken into account
together with the safety regulations in the product documentation.

Safety
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 6
2.4.2 Mounting, Installation, Commissioning and Maintenance
Anyone installing, commissioning, using or maintaining Autronica Fire
and Security products must follow the instructions in this handbook
and other applicable handbooks or standards in order to ensure safe
operation of the products and services.
2.4.3 Modifications to the products
Modifications to the products mentioned in this handbook shall not
be carried out. If a fault or malfunction occurs, the product in
question shall be replaced with a new one. Contact your local
Autronica contact or dealer for further information.
Autronica Fire and Security AS disclaims all liability or responsibility
for any injuries or death, damage, faults, malfunctioning and safety
risks that may occur due to the use of a product that has been
modified.
2.5 Compliance with Standards and Directives
Our product portal http://product.autronicafire.com/certificates/
provides information about certificates, standards and approval
bodies for all variants of the AutroGuard® Multicriteria Protector.
Refer also to Technical Specifications, chapter 4.

Safety
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 7
2.6 Environment Compatibility
2.6.1 Recycling
The product is manufactured using materials and procedures which
comply with current environmental protection standards EMC, RoHS,
LVD and WEEE.
2.6.2 Disposal
The WEEE Directive
The product is considered an electronic device for disposal in
accordance with the European Guidelines. The device must be
disposed through channels provided for this purpose.
The product should not be disposed with other household wastes at
the end of its life cycle. During waste treatment, disposal and
collection, please separate the product from other types of wastes
and recycle it responsibly to promote the sustainable reuse of
material resources. This product should not be mixed with other
commercial wastes for disposal.
Make sure to comply with all local and currently applicable laws and
regulations.

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 8
3. Protector Overview
3.1 Product Decription
The AutroGuard® Multicriteria Protector and its base are designed for
use with Autronica’s interactive fire detection systems.
The AutroGuard® Multicriteria Protector features two heat sensors
and a smoke chamber. The type of operation can be configured to fit
the application, Heat, Optical or Multi Sensor.
AutroGuard® protectors can be delivered in a combination with
integrated sounder, LED indicator and EN54-23 approved visual alarm
device (VAD).
The protector range comprises series V-430 and the SIL2-certified
series V-530. Specific Ex ia or Ex ic versions of the V-530 series are
available for use in use in intrinsically safe areas EX zone 0, 1 and 2.
(See next chapter for information on variants).
The AutroGuard® bases are prepared for easy mounting and
fastening of the protector. The loop diagnostic tool AS2000 can be
used to scan all loops, view the loop topology and type of bases,
verify connections and detect possible short-circuits or breaks on the
loops before protectors are mounted.
Autronica provides also several different variants of protectors
specifically intended for retrofit purposes. These protectors can easily
be mounted onto an existing AutroSafe base (BWA-100/BWA-101).
Autrosafe fire panels support configurations of mixed loops
consisting of both legacy AutroSafe detectors and AutroGuard®
protectors.
Protector (mounted on base)
Base

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 9
3.2 Series / Variants
3.2.1 Protector Variants Without Integrated Alarm Devices

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 10
3.2.2 Protector Variants With Integrated Alarm Devices

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 11
3.3 Details for Ordering
For information about part numbers for AutroGuard® variants, please
visit the Autronica product portal at
http://product.autronicafire.com.
Use the type configuration matrixes in the following chapters when
ordering a variant of the V-430 or V-530 series.
3.3.1 Ordering Information V-430
Use the following matrix to find the correct part number. The
example below shows the type key for a marine certified V-430
including Cover Detection & SelfVerify® 2.0, integrated sounder and
integrated white VAD.
Model
Description
V-430
AutroGuard® multicriteria protector
Type
Extra functions / alarm
methods
Blank
No alarm unit
S
Sounder
VADW
White VAD
VADR
Red VAD
S-VADW
Sounder and white VAD
S-VADR
Sounder and red VAD
Type
Colour
Blank
White RAL9010
BK
Black RAL9005
CC
Customized color
Type
Feature
Blank
No extra features
CD
Cover detection and SelfVerify® 2.0
Type
Additional certification to EN54
Blank
No additional certification
M
MED (Marine certification)
V-430
S-VADR
CD
M
Example
Part no.: 116- V-430-S-VADW/CD/M
116-

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 12
3.3.2 Ordering Information V-530
Use the following matrix to find the correct part number. The
example below shows the type key for an intrinsically safe V-530 for
zones 0, 1 and 2.
Model
Description
V-530
AutroGuard® multicriteria protector with SIL2 approval
Type
Additional functions / alarm types
Blank
No additional function/output
EXIA
Intrinsically safe for zone 0, 1 and 2. ATEX / IECEX / CSA / INMETRO to be specified.
EXIC
Intrinsically safe for zone 2. ATEX / IECEX / CSA / INMETRO to be specified.
S-VADW
Sounder and white VAD*
Type
Colour
Blank
White RAL9010
BK
Black RAL9005
CC
Customised colour
Type
Extra features
Blank
No extra features
HS
Extra high sensitivity**
Example
Part number: 116-V-530-EXIA
*SIL2 approval is not available for sounder and VAD functions, only for the detection
part.
** The extra high sensitivity feature is only available with EXIA and EXIC protectors.
V-530
EXIA
116-

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 13
3.3.3 Ordering Information V-100
Part number
Description
116-V-100
V-100 Standard Base, White.
116-V-100-BK
V-100 Standard Base. Black.
116-V-100-CC
V-100 Standard Base. Customized color to be specified.
116-V-100/M
V-100 Standard Base with marine certification. White.
116-V-100-BK/M
V-100 Standard Base with marine certification. Black.
116-V-100-CC/M
V-100 Standard Base with marine certification. Customized color to be specified.
3.3.4 Ordering Information V-110/V-120
Part number
Description
116-V-110
V-110 SIL2 base, with external LED output. White.
116-V-110-BK
V-110 SIL2 base, with external LED output. Black.
116-V-110-CC
V-110 SIL2 base, with external LED output. Customized color to be specified.
116-V-120
V-120 Ex ia/Ex ic SIL2 base, without external LED output. White.
116-V-120-BK
V-120 Ex ia/Ex ic SIL2 base, without external LED output. Black.
116-V-120-CC
V-120 Ex ia/Ex ic SIL2 base, without external LED output. Customized color to be specified.
3.3.5 Ordering Information Accessories
Part number
Description
116-WAS-2000
AS2000 loop diagnostic too
116-100001215
Air duct sampling unit
116-100001248
Air duct sampling unit in stainless steel
116-100001180
Conduit box 20 mm
116-100001181
Conduit box 25 mm
Part no. not yet available
Telescope removal tool
116-WBJ-5/07
Test gas
116-WBJ-10
Testifire smoke and heat sensor test tool
116-100000927
Detector cover

Protector Overview
Technical Handbook, AutroGuard Multicriteria Protector Series V-430, V-530, V-100, V110 and V-120,
AutroGuard-Technical-Handbook, Doc-1004339, Revision 1, 2020-06-29,
Autronica Fire and Security
Page 14
3.4 Labeling
For information on details regarding marking*, see reference
numbers in drawings on the following pages.
* Note that this overview is intended to show the placement of different markings if
available.
Drawing
Reference
Marking on protector bottom
DOC-1003908
Marking on protector top
DOC-1003788
Marking on protector base
DOC-1003909
Marking
Ref. no.
Autronica logo
10
Type
11a
Part number
11b
Serial number
11c
SW version
11d
CE mark
12a
CPR number
12b
MADE IN (CoO)
12c
EN54 -5
13a
EN54 -7
13b
EN54 -29
13c
EN54 -3
13d
EN54 -23
13e
EN54 -31
13f
EN54 -17
13g
ROHS
14
WEEE Trashbin
15
QR-code (Datasheet)
16
MED wheelmark
20
EAC
21
Ctp
22
(Marking for future UL approval)
23
+FM approval
24
2D-Code. Socket (Unique Id) (serial number, type, part
number, version).
25
ATEX certificate
30
IECEX certificate
31
Ex data
32
ATEX/IECEX WARNING
33a
CSA Ex cert
34
CSA EX WARNING
33b
INMETRO Ex cert
36
INMETRO Ex WARNING
36b