Avalon Pendleton User manual

Small Pedestal (1250, Pendleton, Rainier)
99200127
Page 1 of 4 9/4/08 © Travis Industries, Inc.
Compatibility:
• 1250 Wood Stove
• Pendleton
• Rainier
Packing List:
• Pedestal
• (2) Dowels
• (2) 3/8-16 x 3/4” Bolts w Washers
• (2) 5/16” x 3” Lag Bolts w Washers
• Screen with (6) Staples
• Insulation
• Cover Plate (for use when using outside air on the Rainier and Pendleton)
Pedestal Attachment
NOTE: If using outside air, install it prior to attaching the pedestal (see Outside Air Installation on page 2 and 3).
The dowels insert onto
the front and back edge
of the pedestal base.
Two pedestal bolts
attach the pedestal to
the bottom of the stove.
Pedestal
9/16" Wrench
The lag bolts and washers
may be inserted through
these holes to anchor the
pedestal to the floor.
Stove

Small Pedestal (1250, Pendleton, Rainier)
99200127
Page 2 of 4 9/4/08 © Travis Industries, Inc.
Using Outside Air with the Rainier or Pendleton Wood Stove
The outside air knock-out must be removed and the cover plate installed when using outside air with the Rainier
or Pendleton wood stoves. The 1250 does not require the cover plate or knock-out removal.
Pendleton Outside Air Knock-Out
Outside Air Knock-Out
Rear Blower Knock-Outs
FRONT OF STOVE
Pendleton (45
or 90)
Rainier Outside Air Knock-Out
Outside Air Knock-Out for
Standard Pedestals
Knock-Out for
the Ash Pan
Pedestal Drop
Chute
Rear Blower Knock-Outs
Outside Air Knock-Out for Stoves on Legs
or Stoves Using Ash Pan Pedestal
FRONT OF STOVE
Pendleton Cover Plate
Make sure the button plug is installed in the
center of the cover plate. The cover plate
slides in below the ashlip and covers the air
inlet channel. It has two clips which slide over
the base of the stove, securing it in place.
Rainier Cover Plate
Remove the bridge from the cover plate.
The cover plate slides in below the ashlip
and covers the air inlet channel. It has two
clips which slide over the base of the stove,
securing it in place. Re-attach the bridge to
complete cover plate installation.

Small Pedestal (1250, Pendleton, Rainier)
99200127
Page 3 of 4 9/4/08 © Travis Industries, Inc.
Outside Air Installation – Using the Outside Air Kit (99200139)
AAA
AAA
AAA
AAA
AAA
AAA
AA
AA
AA
AA
AA
AA
AA
A
A
A
A
AA
AA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAA
AAAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
AAAAAAAAA
3" Dia. Flex Duct
(4' max. length)
Select a location between
framing members for the
wall penetration.
NOTE: If wall is thicker
than 8", attach the flex duct
to the hood then slide the
hood into place.
Hood with Rodent Screen
Silicone
Seal the area around
the tube to prevent
air from entering
through the wall.
Silicone
AA
AA
AA
AA
AA
AA
AA
AA
A
A
A
AA
AA
Remove the cover
plate on the pedestal.
Secure the flex duct to the
air duct assembly using
the included hose clamp.
Attach the outside air duct
assembly to the pedestal
with the same screws that
held the cover plate in
place.
b
c
a
Tuck insulation (included with the
pedestal) under both sides of the
pedestal and under the holes on the
base of the pedestal. This prevents air
from being
drawn from below
the pedestal.
A
e
Slide the hood
through the wall and
secure to the outside
wall with the two
included screws.
Cover Plate
d
Slide the cover plate over the flex duct
then attach the flex duct to the hood with
the included hose clamp. Secure the
cover plate to the wall with the included
screws (and drywall anchors if needed).
HINT: The flex must be fully stretched and
the ends cut square and flatted for it to fit
properly. The tube on the hood and air
duct may be crimped if necessary.
Min. 3"
Dia. Hole
8"

Small Pedestal (1250, Pendleton, Rainier)
99200127
Page 4 of 4 9/4/08 © Travis Industries, Inc.
Outside Air Installation –Through the Pedestal into the Crawl Space
This pedestal has an internal air duct that may be used to direct air to the firebox. Outside air is then drawn from
the crawl space under the stove (check with local building codes for requirements in your area). See the
directions below for installation details.
1 Determine the location of the hole placed under the pedestal. The illustration below details the location of the
pedestal in relation to the front of the stove. The hole should be at least 16 square inches.
17"
12"
23"
15-3/4"
Outside air may be drawn
from this area underneath
the pedestal
(min. 16 square inches)
Pedestal Base
(with dowels)
Top View
The faceplate of the Pendleton is 1-
1/8" in front of the forward edge of the
pedestal base.
The faceplate of the Rainier is even
with the forward edge of the pedestal
base.
The faceplate of the 1250 is 1/4" in
front of the forward edge of the
pedestal base.
FRONT
2 Attach the included screen over the hole (staples are included with the pedestal). Tuck insulation under both
sides of the pedestal and under the holes in the base of the pedestal (see step “a”on the previous page).
This prevents air from entering under the pedestal.
Staples are used to attach
the screen to the floor.
Screen is used to prevent
rodents from entering.
AA
AA
AA
AA
AA
AA
AA
AA
Insulation is used to seal the side
edges of the pedestal .
3 Attach the stove to the pedestal.