Avalue Technology UB-A200 User manual

Part No. E2017UBA2A0R
UB-A200
ARTEMIS Anchor
Quick Reference Guide
1st Ed –11 January 2022
Copyright Notice
Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED.

UB-A200
2 UB-A200 Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

Quick Reference Guide
UB-A200 Quick Reference Guide
3
Content
1. Getting Started..........................................................................................................4
1.1 Safety Precautions....................................................................................................4
1.2 Packing List...............................................................................................................4
1.3 System Specifications...............................................................................................5
1.4 System Overview......................................................................................................8
1.4.1 Rear View................................................................................................................................ 8
1.4.2 Rear/Top View......................................................................................................................... 8
1.5 System Dimensions ..................................................................................................9

UB-A200
4 UB-A200 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x UB-A200
1 x Bracket

Quick Reference Guide
UB-A200 Quick Reference Guide
5
1.3 System Specifications
Component
Mother Board
Leverage PCBA of UB-A100 (E9697UBA1E0R)
MCU
ARM® Cortex® -M4 32-bit RISC core, 168 MHz (STM32F407VGT6)
UWB RF Specifications
Chip
DECAWAVE DW1000
Frequency
Channel 1 : 3.25~3.75 GHz for USA
Channel 2 : 3.75~4.25 GHz for USA, Europe
Channel 3 : 4.25~4.75 GHz for USA, Europe, Taiwan
Channel 5 : 6.25~6.75 GHz for China
Physical rate
110K bps
850K bps
6.8 Mbps
Power output (25℃)
-41.3 dBm
Antenna peak gain
5dBi
2.4 Wi-Fi RF Specifications
Chip
AI7688H
Protocol
802.11b/g/n
Antenna
1.5dBi
Software
UWB operating mode
TDoA
Network mode
Bridge mode
WLAN operating mode
AP
Station
AP + Station
Protocol
DHCP
Security
WPA
WPA2
External I/O
LAN Port
1 x RJ-45 (10/100Mbps), support Powered LAN (802.3af/at)
Indicator Light
All LEDs color is GREEN
Power
When power on, LED indicator remains lit.
LAN
When the data of Ethernet is transmitted, the LED indicator flashes.
UWB
When UWB work normally, the LED indicator flashes.

UB-A200
6 UB-A200 Quick Reference Guide
Wi-Fi
When the data is transmitted, the LED indicator flashes.
Others
1 x Reboot button
1 x Function button
Mechanical
Power Type
AT (*whcih means no power switch or button on chassis)
Power Connector Type
1 x DC-in
Power Requirement
+12V DC-in or Powered LAN (802.3af/at)
Mounting
Wall mount
Dimension
182 x 182 x 38mm
Weight
0.4kg
Color
White
Reliability
EMI Test
CE/FCC ClassB
Safety
UL/CB design compatible
Vibration Test
Random Vibration Operation
1 Test PSD : 0.00454G²/Hz , 1.5 Grms
2 System condition : operation mode
3 Test frequency : 5~500 Hz
4 Test axis : X,Y and Z axis
5 Test time : 30 minutes per each axis
6 IEC60068-2-64 Test Fh
Sine Vibration test (Non-operation)
1 Test Acceleration : 2G
2 Test frequency : 5~500 Hz
3 Sweep：1 Oct/ per one minute. (logarithmic)
4 Test Axis : X,Y and Z axis
5 Test time :30 min. each axis
6 System condition : Non-Operating mode
7. Reference IEC 60068-2-6 Testing procedures
Package Vibration Test
1 Test PSD : 0.026G²/Hz , 2.16 Grms
2 Test frequency : 5~500 Hz
3 Test axis : X,Y and Z axis
4 Test time : 30 minutes per each axis
5 IEC 60068-2-64 Test Fh
Mechanical Shock Test
1. Wave form：Half Sine wave
2. Acceleration Rate：10g for operation mode

Quick Reference Guide
UB-A200 Quick Reference Guide
7
3. Duration Time：11ms
4. No. of Shock：Z axis 300 times
5. Test Axis: Z axis
6. Operation mode
7 Reference IEC 60068-2-27 testing procedures
Test Eb : Shock Test
Drop Test
Packing Drop
Reference ISTA 2A, Method : IEC-60068-2-32 Test:Ed Test Ea : Drop
Test
1 One corner, three edges, six faces
2 ISTA 2A, IEC-60068-2-32 Test:Ed
Operating Temperature
0℃~ 55℃
Operating Humidity
40°C @ 95% Relative Humidity, Non-condensing
Storage Temperature
-40 ~ 75°C
Note: Specifications are subject to change without notice.

UB-A200
8 UB-A200 Quick Reference Guide
1.4 System Overview
1.4.1 Rear View
1.4.2 Rear/Top View
Connector
Label
Function
PWR
DC-IN +12V
ETH
RJ-45 Ethernet (10/100 Mbps)
USB
USB 2.0 connector (for reload firmware only)
RST 1/2
RST1：Reboot button
RST2：Combined with RST1 to form a multi-function button

Quick Reference Guide
UB-A200 Quick Reference Guide
9
1.5 System Dimensions
(Unit: mm)