Avalue Technology CCD-07WR2 User manual

Part No. E2017R027A0R
CCD-07WR2
7" Panel PC
Quick Reference Guide
1st Ed –25 October, 2022
Copyright Notice
Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED.

CCD-07WR2
2 CCD-07WR2 Quick Reference Guide
Federal Communication Commission Interference Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception. It is essential that only the supplied
power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
3
FCC RF Radiation Exposure Statement
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant
to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF
Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far
below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a
manner that the potential for human contact during normal operation is minimized. When nearby
persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits
established in the ANSI C95.1 standards, the distance between the antennas and the user should not
be less than 20 cm.

CCD-07WR2
4 CCD-07WR2 Quick Reference Guide
WARNING
“CAUTION – Use suitable mounting apparatus to avoid risk of injury.”
“CAUTION – This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures”
“CAUTION –Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.”
“CAUTION - Use a power cord that matches the voltage of the power outlet, which has been approved
and complies with the safety standard of your particular country.”
“WARNING – To avoid risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.”

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
5
Content
1. Getting Started............................................................................................................6
1.1 Safety Precautions ................................................................................................6
1.2 Packing List...........................................................................................................6
1.3 System Specifications ...........................................................................................7
1.4 System Overview.................................................................................................10
1.4.1 Bottom View............................................................................................................................... 10
1.5 System Dimensions.............................................................................................11
1.5.1 Front and Rear side ................................................................................................................... 11
2. Hardware Configuration...........................................................................................12
2.1 ACP-RK3568 Overviews..........................................................................................13
2.2 ACP-RK3568 Connector list.....................................................................................14
2.3 ACP-RK3568 Jumpers & Connectors settings.........................................................15
2.3.1 OTG ID select (JUSBID) ............................................................................................................. 15
2.3.2 Touch button board connector (JTB1) ........................................................................................ 15
2.3.3 General purpose I/O connector (JDIO1) ..................................................................................... 16
2.3.4 RS-485 connector (JRS485)....................................................................................................... 16
2.3.5 Camera connector (JCAM1)........................................................................................................ 17
2.3.6 A-MIC connector (JAMIC1)......................................................................................................... 17
2.3.7 DC Power-in connector (DCIN2)................................................................................................. 18
2.3.8 Speaker connector (JSPK1)........................................................................................................ 18
2.3.9 10” Touch Panel connector (J10TP) ........................................................................................... 19
2.3.10 21” Touch Panel connector (J21TP1) ....................................................................................... 19
2.3.11 Sensor connector (JSENSE)..................................................................................................... 20
2.3.12 Debug connector (JDBG1)........................................................................................................ 20
2.3.13 Serial port 1 connector (JCOM1) .............................................................................................. 21
2.3.14 RTC Battery connector (JRTC)................................................................................................. 21
2.3.15 LVDS connector (JLVDS).......................................................................................................... 22
2.3.16 MIPI Port (JMIPI)....................................................................................................................... 23
2.3.17 Backlight connector (JLVBL)..................................................................................................... 24
2.3.18 7” Touch Panel connector (J7TP1) ........................................................................................... 24

CCD-07WR2
6 CCD-07WR2 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x CCD-07WR2 Panel PC
1 x Power adapter
1 x Power cord

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
7
1.3 System Specifications
Component
Mother Board
ACP-RK3568
CPU
RK3568_Quad-core Cortex-A55 up to 2.0GHz_ Mali-G52 GPU
Memory
2GB DDR4 on board
Power Supply
DC in
Camera
2MP Camera with Digital Microphone
Wireless LAN
AW-CM276NF_ac/a/b/g/n_2x2
Bluetooth
5.0
Operating System
Android 11, Debian 10
Storage
Other Storage Device
32GB eMMC
Panel
LCD Panel
7” MIPI Panel
Resolution
600 x 1024
Touch Screen
7” USB P-CAP Touch
Touch Controller
EETI_ECX80W32
External I/O
DC in Power jack
JDCIN1: Power Jack_90D
Pwr-in 12V~24V
HDMI Port
JHDMI1: HDMI Port_90D
USB Port
JUSB1: USB Type A Host (3.0)_90D
JUSB2: USB Type A Host (3.0)_90D
Lan Port
JLAN1: 10/100/1000 Lan port_90D
Audio Port
JHP1: Headphone Jack_90D
Reset button
Reset button_90D
Speaker
1.3W Speaker x1 (Left side)
PS: From the HW side, only one issue needs to be pointed out here, because
the serious shortage of TI TPA2012D2RTJT, we decided to put only 1 Audio
Amplifiers instead. But of course, after the supply chain is getting stable later
on, we will follow our original specification with dual Audio Amplifiers.
Mechanical
Power Type
12V~24V wide voltage DC input
Power Connector
Type
DC jack
Dimension
190.86 x 123.61 x 30.5 mm
Weight
0.5 kg
Fanless
Yes

CCD-07WR2
8 CCD-07WR2 Quick Reference Guide
OS Support
Androd 11 / Debian 10
Reliability
EMI Test
CE
FCC class B, RED
Safety
2014/35/EU EN 62368-1: 2014+A11: 2017 (Second Edition)
Low Voltage Directive
Dust and Rain Test
1. PSD: 0.00454G²/Hz, 1.5 Grms
2. Operation mode
3. Test Frequency: 5-500Hz
4. Test Axis: X,Y and Z axis
5. 30 minutes per each axis
6. IEC 60068-2-64 Test:Fh
7. Storage : CF or SSD
Vibration Test
1 Test Acceleration : 2G
2 Test frequency : 5~500 Hz
3 Sweep：1 Oct/ per one minute. (logarithmic)
4 Test Axis : X,Y and Z axis
5 Test time :30 min. each axis
6 System condition : Non-Operating mode
7. Reference IEC 60068-2-6 Testing procedures
Mechanical Shock
Test
1. PSD: 0.026G²/Hz, 2.16 Grms
2. Non-operation mode
3. Test Frequency: 5-500Hz
4. Test Axis: X,Y and Z axis
5. 30 min. per each axis
6. IEC 60068-2-64 Test:Fh
Drop Test
1. Wave form：Half Sine wave
2. Acceleration Rate：10g for operation mode
3. Duration Time：11ms
4. No. of Shock：Z axis 300 times
5. Test Axis: Z axis
6. Operation mode
7. Reference IEC 60068-2-29 Testing procedures Test Eb : Bump Test
Operating
Temperature
1 One corner , three edges, six faces
2 ISTA 2A, IEC-60068-2-32 Test:Ed
Operating Humidity
0°C ~ 40°C
Storage Temperature
40°C @ 95% Relative Humidity, Non-condensing
Other Test
-20°C ~ 60°C

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
9
Note: Specifications are subject to change without notice.

CCD-07WR2
10 CCD-07WR2 Quick Reference Guide
1.4 System Overview
1.4.1 Bottom View
Connectors
Label
Function
Note
LINE-OUOT
Audio line-out connector
HDMI
HDMI connector
USB
2 x USB 3.0 connector
LAN
RJ-45 Ethernet
Reset
Reset button
DCIN
DC power-in connector

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
11
1.5 System Dimensions
1.5.1 Front and Rear side
(Unit: mm)

CCD-07WR2
12 CCD-07WR2 Quick Reference Guide
2.Hardware
Configuration
For advanced information, please refer to:
1- ACP-RK3568 included in this manual.
Note: If you need more information, please visit our website:
http://www.avalue.com.tw

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
13
2.1 ACP-RK3568 Overviews

CCD-07WR2
14 CCD-07WR2 Quick Reference Guide
2.2 ACP-RK3568 Connector list
Jumpers
Label
Function
Note
JUSBID
OTG ID select
3 x 1 header, pitch 2.00 mm
Connectors
Label
Function
Note
JHP1
Audio line-out connector
JHDMI1
HDMI connector
JUSB1/2
2 x USB 3.0 connector
JLAN1
RJ-45 Ethernet connector
JDCIN1
DC Power-in connector
JDCIN2
DC Power-in connector
2 x 2 wafer, pitch 2.00 mm
J21TP1
21”Touch Panel connector
6 x 1 FPC, pitch 0.50 mm
J10TP
10” Touch Panel connector
6 x 1 FPC, pitch 0.50 mm
JSPK1
Speaker connector
4 x 1 wafer, pitch 2.00 mm
SWRST
Reset Button
JNGFF3
M.2 B-Key socket for WWAN
JRTC
RTC Battery connector
2 x 1 wafer, pitch 1.25 mm
JSENSE
Sensor connector
5 x 2 wafer, pitch 2.00 mm
JDIO1
General purpose I/O connector
10 x 2 wafer, pitch 1.00 mm
JCAM1
Camera connector
5 x 2 wafer, pitch 2.00 mm
JCOM1
Serial port 1 connector
5 x 1 wafer, pitch 2.00 mm
JRS485
RS-485 connector
5 x 2 wafer, pitch 2.00 mm
JTB1
Touch button board connector
6 x 2 wafer, pitch 2.00 mm
JAMIC1
A-MIC connector
3 x 1 wafer, pitch 2.00 mm
JMIPI
MIPI Port
40 x 1 FPC, pitch 0.30 mm
JDBG1
Debug connector
3 x 1 wafer, pitch 2.00 mm
JLVDS
LVDS connector
40 x 1 FPC, pitch 0.50 mm
JLVBL
Backlight connector
5 x 1 wafer, pitch 2.00 mm
JSD1
Micro SD card slot
J7TP1
7” Touch Panel connector
6 x 1 FPC, pitch 0.50 mm

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
15
2.3 ACP-RK3568 Jumpers & Connectors settings
2.3.1 OTG ID select (JUSBID)
* Default
HOST*
Client Mode
2.3.2 Touch button board connector (JTB1)
Signal
PIN
PIN
Signal
LED_GREEN_R
11
12
LED_ORANGE_R
BU_BR-_3V
9
10
BU7_3V
PWRBTN_3V
7
8
BU_BR+_3V
VOL_UP_3V
5
6
VOL_DOWN_3V
LINUX_SW
3
4
BU1_TV_3V
PWR_JTB1
1
2
GND

CCD-07WR2
16 CCD-07WR2 Quick Reference Guide
2.3.3 General purpose I/O connector (JDIO1)
Signal
PIN
PIN
Signal
DIO_GP10
1
2
DIO_GP20
DIO_GP11
3
4
DIO_GP21
DIO_GP12
5
6
DIO_GP22
DIO_GP13
7
8
DIO_GP23
DIO_GP14
9
10
DIO_GP24
DIO_GP15
11
12
DIO_GP25
DIO_GP16
13
14
DIO_GP26
DIO_GP17
15
16
DIO_GP27
I2C_2_LV_SDA
17
18
I2C_2_LV_SCL
+V5S_DIO
19
20
GND
2.3.4 RS-485 connector (JRS485)
Signal
PIN
PIN
Signal
GND
2
1
GND
NC
4
3
485_422TX1+
NC
6
5
485_422TX1-
RS232_RX4
8
7
NC
RS232_TX4
10
9
+PWR_RS485

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
17
2.3.5 Camera connector (JCAM1)
Signal
PIN
PIN
Signal
GND
1
2
GND
GND
3
4
GND
USB2_HOST3_DP_R
5
6
PDM_SDI1_DMIC_R
USB2_HOST3_DM_R
7
8
PDM_CLK1_DMIC_
+CAM_VCC
(5V level)
9
10
+DMIC_VCC
(3V level)
2.3.6 A-MIC connector (JAMIC1)
Signal
PIN
GND
1
AMIC_IN
2
MIC_JD#
3

CCD-07WR2
18 CCD-07WR2 Quick Reference Guide
2.3.7 DC Power-in connector (DCIN2)
Signal
PIN
PIN
Signal
+12V_24ADPIN
1
3
+12V_24ADPIN
GND
2
4
GND
2.3.8 Speaker connector (JSPK1)
Signal
PIN
SPK_L+
1
SPK_L-
2
SPK_R+
3
SPK_R-
4

Quick Reference Guide
CCD-07WR2 Quick Reference Guide
19
2.3.9 10” Touch Panel connector (J10TP)
Signal
PIN
NC
6
GND
5
GND
4
USB2_10TP_DP
3
USB2_10TP_DM
2
+USB_5V_TS
1
2.3.10 21” Touch Panel connector (J21TP1)
Signal
PIN
+USB_5V_TS
1
USB2_21TP_DM_R
2
USB2_21TP_DP_R
3
GND
4
GND
5
GND
6

CCD-07WR2
20 CCD-07WR2 Quick Reference Guide
2.3.11 Sensor connector (JSENSE)
Signal
PIN
PIN
Signal
GND
1
2
GND
SENSE0_IRQ_R
3
4
SENSE2_IRQ_R
I2C3_SDA_3.3V_CONN
5
6
I2C5_SDA_3.3V_CONN
I2C3_SCL_3.3V_CONN
7
8
I2C5_SCL_3.3V_CONN
+3VS_SEN_CONN
9
10
+3VS_SEN_CONN
2.3.12 Debug connector (JDBG1)
Signal
PIN
DEBUG_TX2_CON
1
DEBUG_RX2_CON
2
GND
3