Avalue Technology SID-15WR1 User manual

Part No. E2017S5R1A1R
SID-15WR1
15.6" Panel PC with Rockchip RK3288 SoC, 2G RAM, 16G
eMMC
Quick Reference Guide
2nd Ed –27 September 2021
Copyright Notice
Copyright 2021 Avalue Technology Inc., ALL RIGHTS RESERVED.

SID-15WR1
2 SID-15WR1 Quick Reference Guide
FCC Statement
Federal Communication Commission Interference Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception. It is essential that only the supplied
power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Quick Reference Guide
SID-15WR1 Quick Reference Guide
3
FCC RF Radiation Exposure Statement
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant
to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF
Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far
below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a
manner that the potential for human contact during normal operation is minimized. When nearby
persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits
established in the ANSI C95.1 standards, the distance between the antennas and the user should not
be less than 20 cm.
WARNING
“CAUTION –Use suitable mounting apparatus to avoid risk of injury.”
“CAUTION - Use a power cord that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular country.”
“WARNING –To avoid risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.”
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2021 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that

SID-15WR1
4 SID-15WR1 Quick Reference Guide
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

Quick Reference Guide
SID-15WR1 Quick Reference Guide
5
Content
1. Getting Started............................................................................................................6
1.1 Safety Precautions ................................................................................................6
1.2 Packing List...........................................................................................................6
1.3 System Specifications ...........................................................................................8
1.4 System Overview.................................................................................................11
1.4.1 I/O View...................................................................................................................................... 11
1.5 System Dimensions.............................................................................................12
2. Hardware Configuration...........................................................................................13
2.1 SID-15WR1 connector mapping..........................................................................14
2.1.1 Serial port connector (COM)...................................................................................................... 14
2.1.2 RJ-45 Ethernet connector (LAN) ............................................................................................... 14
2.1.3 HDMI connector (HDMI) ............................................................................................................ 15
2.1.4 USB2.0 connector (USB2.0)...................................................................................................... 15

SID-15WR1
6 SID-15WR1 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x SID-15WR1 Panel PC
1 x Power adapter
1 x Power cord
1 x Screw
1 x Antenna

Quick Reference Guide
SID-15WR1 Quick Reference Guide
7
Definitions
Warning! Class I Equipment. This equipment must be earthed. The power plug must be
connected to a properly wired earth ground socket outlet. An improperly wired socket
outlet could place hazardous voltages on accessible metal parts.
Caution! Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions."
Warning! For RTC battery, current statement in the manual is acceptable.
There is danger of explosion if the battery is mishandled or incorretly replaced.
Replace only with the same type of battery. Do not disassemble it or attempt to
recharge it outside the system. Do not crush, puncture, dispose of in fire, short the
external contacts, or expose to water or ther liquids. Dispose of the battery in accordance with local
regulations and instructions from your service provider.

SID-15WR1
8 SID-15WR1 Quick Reference Guide
1.3 System Specifications
Component
Mother Board
ACP-RK3288B
CPU
RockChip RK3288-W Cortex-A17, Quad Core 1.8GHz
CPU Cooler (Type)
Aluminum type w/ Shielding cover
Memory
2GB DDR3L on board
Power Supply
DC-in 12V~24V wide voltage DC input support
Adapter
AC/DC adapter 12V/5A, screw type
Wireless LAN
802.11 b/g/n Wireless LAN on board
Bluetooth
Bluetooth 4.0 on board
Operating System
Android 8.1
Storage
Solid State Drive
16GB eMMC on board
Panel
LCD Panel
- BOE NV156FHM-N42 15.6” TFT-LCD
- 16:9 wide screen, 1920 x 1080
- eDP Interface
Touch Screen
ACDC DY1562W-4262
- Projective Capacitive, Multi touch, 10 points
- Hardness: ≥6H
- Transmission: ≥85%
- USB Interface
Touch Controller
Silicon Works-SW4101D
External I/O
Serial Port
1 x DB9 for RS-232(Tx/Rx, Default)
USB Port
2 x USB 2.0 ports (Type A), Option 3th USB 2.0 port
Video Port
1 x HDMI 2.0 port (Type A)
Audio Port
1 x Line out jack (Audio/Green)
LAN Port
1 x Gigabit Ethernet (RJ-45 connector)
Wireless LAN
Antenna
1 x Dipole Antenna
Switch
1x Power button w/ LED
Others
1 x Reset button
Power Requirement/Mechanical
Power Type
12V~24V wide voltage DC input
Power Connector
Type
2.5mm DC-in jack

Quick Reference Guide
SID-15WR1 Quick Reference Guide
9
Construction
Metal
Color
Black
Dimension
391.2 x 239.2 x 48.1mm
Weight
3.59 kg
Fanless
Yes
IP Rating
Front IP65
Reliability
EMI Test
CE/FCC Part 15, Subpart B
Safety
IEC-60950-1 & EN 60950-1
Dust and Rain Test
Front Panel IP65
Random Vibration
Test
Test Standard: Reference IEC60068-2-64 Testing procedures
1. System condition: Operation mode
2. PSD: 0.00454G²/Hz , 1.5 Grms
3. Test Frequency : 5-500Hz
4. Test Axis : X,Y and Z axis
5. Test time: 30 minutes per each axis
6. Storage : eMMC
Sine Vibration Test
(Non-operation)
Test Standard: Reference IEC60068-2-6 Testing procedures
1. System condition : Non-Operating mode
2. Test Acceleration : 2G
3. Test frequency : 5~500 Hz
4. Sweep：1 Oct/ per one minute. (logarithmic)
5. Test Axis : X,Y and Z axis
6. Test time :30 min. each axis
Packing Vibration
Test
Test Standard: Reference IEC60068-2-64 Testing procedures
1. Non-operation mode
2. PSD: 0.026G²/Hz , 2.16 Grms
3. Test Frequency : 5-500Hz
4. Test Axis : X,Y and Z axis
5. Test time: 30 min. per each axis
Mechanical Shock
Test
Test Standard: Reference IEC60068-2-29 Testing procedures
1. System Condition: Operation
2. Wave form: Half-Sine wave
3. Acceleration: Rate: 10g
4. Duration: Time: 11ms
5. No. of Shock: Z axis 300 times
6. Test Axis: Z axis
Packing Drop Test
Reference ISTA 2A, Method: IEC-60068-2-32 Test:Ed
1. Test Phase: One comer, three edges, six faces
2. Packing weight: around 1.5kg

SID-15WR1
10 SID-15WR1 Quick Reference Guide
3. Test high: 96.5cm (Based on product weight
Operating
Temperature
0°C ~ 40°C (32°F ~ 104°F)
Operating Humidity
40°C @ 95% Relative Humidity, Non-condensing
Storage Temperature
-20°C ~ 60°C (-4°F ~ 140°F)
Note: Specifications are subject to change without notice.