Avantree TC026 User manual

5. Charging
When the LED flashes RED, you should recharge the device. It normally takes
about 2 hours to fully charge the battery. The LED will stay RED when charging and
will turn off when charging is complete.
Charging Requirement
You can connect TC026 via the supplied micro USB cable to your own USB
chargers (wall charger/travel charger/car charger, etc.) with 5V/500mA-1A or PC
USB port. It’s ok to use most mobile phone chargers on the market.
Note: We suggest you fully charge the device at least every two months.
- 9 -
5). What is the PIN code?
If a PIN code is required for pairing, try 0000 (four zeroes), 8888 (four eights), 1111
(four ones), or 1234.
6). Can I use TC026 while charging?
Yes, you can. But it will automatically turn itself off when charging. Please turn
TC026 on again, it will automatically reconnect to the last device.
Note: The USB outputs of some TVs or laptops are unstable. When used while
charging, we suggest you connect to a wall charger instead of a USB port.
More video user guide for TC026 on Youtube.com
Telephone support: booking from Avantree.com
More FAQs and instructions on support.avantree.com
Email support: [email protected]
7. Product Specifications
• BT version: 4.1
• BT profile: A2DP, AVRCP
• Operational range: Class II, 10M
• Working time: Up to 9 hours in RX mode; Up to 10 hours in TX mode.
• Charging time: 2 hours
• Product weight: approx. 21g
• Product size: 55*38*10.5mm
- 12 - - 14 -
- 2 -
2. As a Bluetooth Transmitter
2.1. Bluetooth Pairing & Connection
Step 1. From off, slide TX/RX switch to TX position. Then turn on TC026 – press
and hold MFB button for 3 seconds.
Step 2.
Enter PAIRING MODE – double click MFB, the LED flashes BLUE very quickly.
Step 3. Set your Bluetooth headphones/receiver to *PAIRING MODE*
Step 4. Keep the devices close and wait for 5~30 seconds. Once connected, the
LED on TC026 will stay BLUE.
PAIRING MODE: Discoverable mode for Bluetooth device, normally the LED flashes
very quickly constantly or flashes two colors alternately.
- 3 -
2.2. Connect to two Bluetooth headphones/speakers simultaneously
Step 1. Connect to your first device as above. Then turn off the first device and
TC026.
Step 2. Set second device to PAIRING MODE.
Step 3. Set TC026 to PAIRING MODE again – Turn on, then double click MFB. The
LED flashes BLUE very quickly.
Step 4. Keep the devices close and wait for 5~30 seconds. Once connected, the LED
on TC026 will stay BLUE. Then turn off TC026 again.
Step 5. Turn on the first device and TC026 again, wait for 5~30 seconds, TC026 will
automatically connect to two devices.
Note: If TC026 can’t re-connect to two devices, please try to turn it off and on again.
- 4 -
3.2. Connect to two phones/tablets simultaneously
Step 1. Connect the first phone as above.
Step 2. Set TC026 to PAIRING MODE again – double click MFB,
the LED flashes
BLUE and RED alternately
.
Step 3. Activate Bluetooth on your second phone/tablet, search and select
“Avantree TC026” to connect.
Step 4. Turn off TC026 and turn on again. It will automatically connect to two
devices simultaneously.
- 7 -
- 6 -
4. LED indications
3. As a Bluetooth Receiver
3.1. Bluetooth Pairing & Connection
Step 1. From off, slide TX/RX switch to RX position.
Step 2. Turn on TC026 – press and hold MFB button for 3 seconds.
Step 3.
Enter PAIRING MODE – double click MFB, the LED flashes BLUE and RED
alternately.
Step 4. Activate Bluetooth on your phone/tablet, search & select “Avantree TC026”
to connect. Once connected, the LED on TC026 will stay BLUE.
Step 5. Connect TC026 to your wired headphone/speaker system via 3.5mm audio
cable. Then you can wireless streaming music now.
Z-PKMN-TC026-V1
www.avantree.com
[email protected]
Micro USB cable
Charge from a wall charger Charge from PC
Press Volume + once
Previous track
Volume –
*Just available in
RX mode* Press Volume - once
BTI-025
Dispose of the packaging and
this product in accordance with
the latest provisions.
2.3. Connect TC026 to TV or other audio source
Connect TC026 to your TV or other analog audio source via 3.5mm audio cable. Then
TC026 is ready for use now.
Note: If no sound from headphones after connection, please use a wired earphones
to test if you can heard the sound from the audio jack on TV or audio source.
- 5 -
6. Important Notices & FAQ
1). AptX Low Latency
TC026 just support aptX low latency in TX mode. In this mode, if you still experiencing
audio delay, it is most likely due to your headphones/receiver without Low Latency
Support.
Due to aptX technology limitation, aptX Low Latency codec does NOT support under
dual link.
2). Reconnect
Once powered on, TC026 will reconnect with the last connected device automatically
within 5 seconds. If not, you may press MFB once to stimulate the process.
3). Auto power off
Once disconnected over 5 minutes, TC0026 will automatically power itself off.
4).How to erase the previous pairing history?
Step 1. Turn Off TC026.
Step 2. After 3 seconds, slide the TX/RX switch to other side. Then power on.
- 10 - - 11 -
1. Product Overview
A. Avantree TC026 adapter
B. 1 pc 3.5mm audio cable
C. 1 pc micro USB charging cable
D.
User manual & Quick user guide
- 1 -
- 8 -
www.avantree.com
User Manual
Wireless Transmitter Receiver 2-in-1 Adapter
TC026
For a Beer Experience
For a Beer Experience
www.avantree.com
UserManual
BluetoothTransmitterReceiver 2-in-1 Adapter
TC026
For a Beer Experience
Contents
1. Product Overview
2. As a Bluetooth Transmitter
2.1. Bluetooth Pairing & Connection
2.2. Connect to two Bluetooth headphones/speakers simultaneously
2.3. Connect TC026 to TV or other audio source
3. As a Bluetooth Receiver
3.1. Bluetooth Pairing & Connection
3.2. Connect to two phones/tablets simultaneously
4. LED Indications
5. Charging
6. Important Notices & FAQ
7. Product Specifications
1
12
10
9
8
6
7
6
4
3
3
A
BTI-025
B C D
MFB
Basic operaon
Button Function Operation
Power on/off Hold MFB for 3 seconds to turn TC026 on/off
Enter pairing mode
After turn on, double click MFB, LED indicator
will flashes BLUE and RED alternately in RX
mode / flashes BLUE quickly in TX mode.
Reconnect by manual Press MFB once
Play/Pause
Press MFB once when music streaming in RX mode.
Switch between transmitter and receiver mode.
* Once switch the mode, the previous pairing history will be erased *
TX/RX switch
Volume +
*Just available in
RX mode*
Volume up
Next track
Press and hold Volume +
Volume down Press and hold Volume -
PairSet
Keep close & wait 5~30s, once connected,
LED will stay BLUE.
3
Connect
From OFF mode, set switch to “TX” side
Get headset or
speaker into
PAIRING MODE*
Turn on & double
click MFB, LED will
flashes BLUEvery
quickly
Transmier
Mode
3Connect
Avantree Saturn Pro
Search & Connected
1M
Pair
Turn on, then double click MFB.
LED flashes BLUEand RED alterately.
PAIRING MODE
Set
Power off
Connected
Disconnected
Low battery
Charging
LED flashes RED 2 times
LED flashes BLUE 2 times
LED flashes BLUE quickly in TX mode
LED flashes BLUE and RED alternately in RX mode
LED stays BLUE
LED flashes BLUE 2 times every 3 seconds in RX mode
LED flashes RED quickly
LED stays RED
Status LED indicator
Power on
Pairing mode
Fully charged LED turns off
LED flashes BLUE once every second in TX mode
5
BTI-025
TC026
TC026
BTI-025
BTI-025
LED indicator
TX/RX mode switch
TX: Transmitter
RX: Receiver
Micro USB charging port
3.5mm
audio port
Multi-function button(MFB)
Volume -
Volume +
TC026
TC026
3.5 mm audio cable
What’s in the box?
TX RX
Set
From OFF mode, set switch to “RX” side
Receiver
Mode
TX RX