Avaya Cajun P580 User manual

610-0178-094 1
October 2002
CHAPTER 1
Installing Avaya P550™/P580/P880/P882
Gigabit Ethernet Modules
Overview
This document describes the following processes:
■Gigabit-Speed Modules
■Compliance Information
■Software Requirements
■Power Requirements
■Installing the Modules
■Installing GBIC Connectors
■Installing the Cables
Gigabit-Speed Modules
This document describes installation and configuration of the
following media modules:
50 Series Modules
■2-Port, Full-Duplex 1000BASE-X module: 850 nm (SX)
and 1310 nm (LX and SLX) - (Layer 2 and Layer 3)
■4-Port, Full-Duplex 1000BASE-X module: 850 nm (SX)
and 1310 nm (LX and SLX) - (Layer 2)
80 Series Modules
■4-Port, Gigabit Interface Card (GBIC) based module:
850 nm (SX), 1310 nm (LX and SLX) and 1550 nm (ELX)
(Layer 2 and Layer 3)
■8-Port, Gigabit Interface Card (GBIC) based module:
850 nm (SX), 1310 nm (LX and SLX) and 1550 nm (ELX)
(Layer 2 and Layer 3)

610-0178-094
2 October 2002
Compliance Information
Please read the following compliance information prior to installing
your Avaya Gigabit Ethernet Module.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet apparell numérique de la classe A respecte toutes les exigences
du Régelment sur le matériel brouilleur du Canada.
WARNING
This is a class A product. In a domestic environment, this
product may cause radio interference, in which case you may
be required to take adequate measures.
Laser Safety Information
* Note: This notice applies to devices that contain optical
transceiver media modules installed.
The transceivers used in this product are Class 1 Laser Products. This
product complies with 21 CFR Chapter 1, Subchapter J.
Any use other than that specified herein may result in hazardous
laser radiation exposure.
Unterminated optical receptacles may emit laser radiation. Do not
view with optical instruments.
This product complies with IEC 60825-1, Safety of Laser Products,
Class 1 Laser Product.

3
610-0178-094 October 2002
Software Requirements
The Avaya P550R/P580/P880/P882 80-Series modules require
software of Version 5.0 or higher.
Power Requirements
In the P550 chassis, each power supply powers approximately four
media modules.
In the P880 chassis, each power supply powers approximately nine
media modules.
It takes two power supplies to power a full chassis. Using three
power supplies ensures that the system has redundant power
capabilities.
Use Tables 1 and 2 for the precise power values:
Table 1. Power Values for System Devices - 50-Series Modules
Table 2. Power Values for System Devices - 80-Series Modules
Select Power System from the System > Configuration > group
on the web agent window to determine how much power is
currently available in your switch.
Device Power Used
2-Port Gigabit Module 35 W
4-Port Gigabit Module 55 W
Device Power Used
4-Port Gigabit Module 45 W
8-Port Gigabit Module 75 W

610-0178-094
4 October 2002
Installing the Modules
* Note: All Avaya media modules are hot swappable. You do not
need to shut down the switch when adding modules.
To install modules in the chassis:
1. Carefully remove the module from its box, leaving the module in
its anti-static wrapping.
2. Take appropriate antistatic precautions and carefully remove the
module from the antistatic wrap (refer to Chapter 1,
“Installation” in the Avaya P550/P580/P880/P882 Multiservice
Switch Installation Guide for detailed information on proper
antistatic precautions).
3. Open the Ejector Tabs until the stops make contact with the face
plate (Figure 1).
Figure 1. Installing the Module
4. Insert the module into the chassis (Figure 1).
5. Press on the center of the module as you push it into the chassis.
The ejectors snap into place.
6. Push the ejectors into the closed position to complete seating
the module (Figure 2).

5
610-0178-094 October 2002
Figure 2. Closing the Ejector Tabs
7. Tighten the captive screws.
As the module powers up, the LEDs should function as described in
the module descriptions provided in the Avaya P550/P580/P880/P882
User Guide. In general, the following is observed on a properly-
functioning module (Table 3 ):
Table 3. Power-up LED Function
Module LED Normal Behavior
All Modules Module Status Solid green, indicating normal
operation.
Gigabit
Modules
TX and RX Solid green, flashing yellow
intermittently to indicate traffic
Port Solid green, indicating link integrity.
HD/FD Solid green, indicating full-duplex
operation.

610-0178-094
6 October 2002
Installing GBIC Connectors
GBIC connectors are only applicable to 80-Series modules. They
come in the following types:
■SX (550m-capable)
■LX (10km-capable)
■SLX (25km-capable)
■ELX (70-100km-capable)
Refer to Table 4 and Table for distances and wave lengths.
* Note: All Avaya GBIC connectors are hot swappable. You do not
need to shut down the switch when adding modules.
To install a GBIC connector into a module:
1. Carefully remove the GBIC connector from its packaging, leaving
the module in its anti-static wrapping.
2. Take appropriate antistatic precautions and carefully remove it
from the antistatic wrap. (Refer to the Avaya P550/P580/P880/
P882 Multiservice Switch User Guide for more information on
proper antistatic precautions).
3. Carefully slide the GBIC connector into the module until the side
connectors click into place (Figure 3).

7
610-0178-094 October 2002
Figure 3. Installing a GBIC Connector
Installing the Cables
Install the appropriate cables for your network configuration. The
Avaya P550/P580/P880/P882 Multiservice Switch supports the
following cable type:
■Fiber cables with SC-type connectors
Optical Channel Requirements
The optical fiber types that can be used with the Gigabit Ethernet
Modules are standard single-mode and multimode optical fibers that
conform to the requirements of the following standards.
Single-mode Optical Fiber:
■IEC 60793-2 B1.1 (dispersion unshifted single-mode) or
■IEC 60793-2 B1.3 (low water peak single-mode)
■ITU-T Recommendation G.652 –Dispersion Unshifted Fiber

610-0178-094
8 October 2002
■TIA/EIA 492CAAA Dispersion-Unshifted Single-Mode
Optical Fibers or TIA/EIA 492CAAB Dispersion-Unshifted
Single-Mode Optical Fibers with Low Water Peak
Multimode Optical Fiber:
■TIA/EIA 492AAAA 62.5/125 micron Multimode Optical
Fiber
■TIA/EIA 492AAAB 50/125 micron Multimode Optical Fiber
■TIA/EIA 492AAAC 50/125 micron Laser Optimized
Multimode Optical Fiber
■IEC 60793-2-10 type A1a.2 (in preparation)
Examples of optical fibers that meet these requirements include (but
are not limited to):
Single-mode Optical Fiber
■Corning®SMF-28™ Fiber
■Corning®SMF-28e™ Fiber
■OFS Fitel Single-Mode Fiber
■OFS Fitel AllWave®Fiber
■Avaya Systimax Single-Mode Fiber Cable
Multimode Optical Fiber
■Corning Infinicor
■Corning Infinicor SX
■OFS GigaSPEED
■OFS LazrSPEED
■Draka Comteq Max Cap 300

9
610-0178-094 October 2002
Refer to Table 4 and Table 5 for supported link distances for the
Gigabit Ethernet Modules.
Table 4. Supported Link Distances
Table 5. Supported Link Distances - GBICs
Model
Number
Wavelength Fiber Type Link
Distance (m)
M5504-
1000SX
M5502-
1000SX
M5502R-
1000SX
850 nm 50 µm MMF
• 400 MHz*km
• 500 MHz*km
• 2 to 550
• 2 to 550
62.5 µm MMF
• 160 MHz*km
• 200 MHz*km
• 2 to 220
• 2 to 275
M5504-
1000LX
M5502-
1000LX
M5502R-
1000LX
1310 nm 50 µm MMF
• 400 MHz*km
• 500 MHz*km
• 2 to 550
• 2 to 550
62.5 µm MMF
• 160 MHz*km
• 200 MHz*km
• 2 to 550
• 2 to 550
9/10 µm SMF 2 to 5000
M5504-
1000SLX
M5502-
1000SLX
M5502R-
1000SLX
1310 nm 62.5 µm MMF
• 160 MHz*km
• 200 MHz*km
• 2 to 550
• 2 to 550
9/10 µm SMF 2 to 10000
GBIC Part
Number
Wavelength Fiber Type Link
Distance (m)
M8001-
1000SX
850 nm GBIC 50 µm MMF
• 400 MHz*km
• 500 MHz*km
• 2 to 550
• 2 to 550
62.5 µm MMF
• 160 MHz*km
• 200 MHz*km
• 2 to 220
• 2 to 275

610-0178-094
10 October 2002
Table 6 lists the optical fiber specifications for the Gigabit Ethernet
Modules.
Table 6. Optical Fiber Specifications
a. For the single-mode case, the 0.4 dB/km attenuation for optical fiber cables is
defined in ITU-T G.652.
M8001-
1000LX
1310 nm GBIC 62.5 µm MMF
• 160 MHz*km
• 200 MHz*km
• 2 to 550
• 2 to 550
9/10 µm SMF 2 to 10000
M8001-
1000SLX
1310 nm GBIC 9/10 µm SMF 2 to 25000
M8001-
1000ELX
1550 nm GBIC 9/10 µm SMF Up to 70,000
to 100,000
GBIC Part
Number
Wavelength Fiber Type Link
Distance (m)
Description 62.5 µm MMF 50 µm MMF Type B1.1, B1.3 SMF Unit
Nominal fiber
specification
wavelength
850 850 1310 1550 nm
Fiber cable
attenuation
(max)
3.5 3.5 0.4aor 0.5bSee Footnote
c
dB/km
Modal
bandwidth
(min)
160dor 200d400dor 500d
or 2000e
N/A MHz km
Zero
dispersion
wavelength
(λ0)
1320 ≤λ0≤1365 1295 ≤λ0≤
1320
1300 ≤λ0≤1324 nm
Dispersion
slope (max)
(S0)
0.11 for
1320 ≤λ0≤1348
and
0.001(1458 - λ0)
for
1348 ≤λ0≤1365
0.11 for
1300 ≤λ0≤
1320
and
0.001(1190 -
λ0)
for
1295 ≤λ0≤
1300
0.093 ps / nm2km