Avermedia AVerDiGi EB1304 NET User manual

AVerMedia®AVerDiGi EB1304 NET
Quick Installation Guide
1
Package Contents
0
FN
RIGHT
UP
LEFT
EBDVR
23
56
89
7
1
4
▼
▼
▼
▼
▲
REC
A-B
MEN
U
SELECT
ZOOM
-
SPEED
+
SPEE
D
- FOCU
S
-
ZOOM
+
D
OWN
FOCUS
+
▲
▼
RM-H6
▼
▼
PTZ
AVerMedia
AVerDiGiEB1304NET
QuickInstallationGuide
AVerDiGi EB1304 NET unit
Remote Control (Batteries are
included)
Power Cord (*The power cord
may vary according to the local
electricity system.)
Power Adaptor
DVR accessories (4 screws)
Quick Installation Guide
Software CD (Manual is
included)
i
If there is any damage, shortage or inappropriate item in the package
contents, please contact with local dealer

2
Hardware Installation
A. Install the hard disk
Follow the steps to install the hard disk:
Install the Hard Disk Inside the DVR System
Loosen screws
Remove the case cover
backward and upward
Loosen the screws on the hard
disk rack
Tighten screws at sides of the
hard disk
Connect the IDE cable
connector to the hard disk, and
then connect the power connect
to the hard disk power slot
Tighten the screws to fix the hard
disk.
Close the case cover
Tighten screws
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
ARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT
MODIFICATIONW

3
B. After the hard disk installation, please connect the cables
and power as the illustration showed
Using DVR System
1. Power on the system. DVR
will check the hard disk status.
If the hard disk is new to the
system, the screen will appear
“HDD FORMAT YES/NO”.
2. Press to format hard
disk. And then, user will see
“HDD FORMATTING” on the
DVR screen
3. When the DVR screen shows
“NEW HDD FORMAT
COMPLETED”, the formatting
is completed
4. When you see the screen,
press to enter the OSD
main menu screen to setup
parameters. After finishing
setup, press to return
to surveillance screens.

4
5. As surveillance screens
appear, press
REC
button to
record.
6. Press
1 3
7 9
buttons to switch to each
channel.
Setup Time and Date
For the first time using, please adjust the system date and time in order
to have correct recording time.
1. Press and select
Submenu
→Date / Time
2. Use
▲
and
▼
to go up and
down
3. Use or
▼
to make a
selection
4. Use
▼
and
▼
buttons to move the selection to the left and
right
Network Setup
Configuring network parameter for remote accessing.
-Use
▲
and
▼
to go up and
down
-Use or
▼
to make a
selection
-Use
▼
and
▼
buttons to go
left and right
1. Press and select
NETWORK
SETUP.
2. Select
IP MODE
-STATIC: Assigns a constant IP address to DVR system.
-DHCP: Assign an IP address by local DHCP server.
-PPPOE: Point-to-Point Protocol over Ethernet is a network
protocol for encapsulating PPP frames in Ethernet frames. It is
2006 / 04 / 20
17 : 54 : 50
ON
ON
ON
OFF
NO
SUBMENU
PASSWORD CHANGE
VIDEO ADJUSTMENT
DATE
TIME
AUTO RECORD
AUTO SCAN
PASSWORD SETUP
AUDIO RECORD
AUDIO MUTE NTSC
OFF
1
VIDEO SYSTEM
MUTIPLE REMOTE
REMOTE ID
123 4
5001
5005
NETWORK SETUP
IP MODE
CHANNEL
VIDEO PORT
UPGARDE PORT
STATIC

5
USB BAKCUP
TIME SET
START TIME
END TIME : 2006 / 05 / 05 13 : 08 : 13
: 2006 / 05 / 04 10 : 00 : 01
BACKUP CHANNEL
BACKUP SIZE
BACKUP EXECUTE
123 4
73GB 89MB
used mainly with ADSL services. If your network is using ADSL
service to connect to internet, and then, select PPPOE mode.
3. SUBNET: Enter the subnet mask of the IP address ( Only STATIC
IP mode need to enter)
4. GATEWAY: Enter the network gateway IP address from your local
network (Only STATIC IP mode need to enter)
5. DNS: Domain Name Server translates domain names (such as
www.abb.com.tw) to IP addresses. Enter the IP address of DNS if it
is available. (Only STATIC IP mode need to enter)
6. MAC ADDRESS: Only for user information. Don’t need to enter the
MAC address in any IP mode.
7. When all parameters are set, select the CHANGE and press
to save the configuration.
i
To register a domain name for the DVR system, please go to
www.ddns.avers.com.tw or refer to the user manual on 8.1.14
Network Setup and Appendix A Registering Domain Names.
Backup Recorded Video to Pen Drive or Hard Disk
Backup by Time Search
User can backup recorded video to pen drive or external hard disk, and then,
playback on the PC.
-Use
▲
and
▼
to go up and
down.
-Use or
▼
to make a
selection.
-Use
▼
and
▼
buttons to go left
or right.
1. Plug in pen drive or external hard disk
to the USB port on the DVR system.
2. Press and select
USB BACKUP.
3. Select the
START TIME and END TIME.
4. Select the channels which want to backup.
5. The DVR system will display the system hard disk space and backup

6
USB BAKCUP
YES(SELECT) / NO(MENU)
file size.
6. And then, select BACKUP EXECUTE to start backup video to the USB
device.
Backup AB Repeat File
In playback mode, user also can backup the AB repeat video file which user
has set by using theAB repeat function.
1. Press
▲
(play button) to call out the SEARCH MODE menu to find
the period of recorded video that user wants to backup.
2. Select
TIME SEARCH or EVENT LIST.
-TIME SEARCH (search by date and time): select the date and time
from where you want to begin the video playback.
-EVENT LIST (search by condition): select from the list.
3. During the playback, press
A-B
to set
the A point of video segment.And then,
press
A-B
again to set the B point of
video segment. On the surveillance
screen will repeat playing theAB point
video segment which user has set. To
cancel AB repeat, press
A-B
again.
4. To backup the AB point video segment, press . A confirmation
window appears, and then, presses to start backup file.
Playback and Edit Backup File on PC
To install the USB Playback Application:
1. Place Installation CD into the CD-ROM drive. When the installation
main screen appears, click Install USB Playback Application and
then follow the on screen instructions
2. Select the language you prefer
3. Click
OK to install the application
4. Click
Exit to close the installation main screen. You may now
connect the USB device to your PC.

7
5. To run the application, click the USB Player icon on the PC
desktop
6. To playback the backup file, plug in pen drive or external hard disk
which user has backup the files to it. And then, click OPEN FILE
button and select the file source.
For more information, please refer to the operation manual in the software
CD. If you still have inquiries, please log on to http://www.avermedia.com
http://www.averdigi.com for troubleshooting