avertX AVX-HD848IRM User manual

This is a quick reference for users to install and operate the HD848IRM
camera. It provides only basic information regarding camera installation,
setup, and operation. For further details, please download the HD848IRM
User Manual at www.avertx.com.
PACKAGE CONTENTS
HD848IRM Camera
Waterproof Cable
Connector
Quick Start Guide
HD848IRM QUICK START GUIDE
Screws & Anchors
AVX-HD848IRM | QUICK START GUIDE
37716AA
T20 Torx Tool
Mounting Template
Paintable Dome
Cover
2
1
CABLE CONNECTIONS
CONTACT OUR PRO TEAM
PHONE: [phone] EMAIL: [email protected] CHAT: https://help.avertx.com/
3
MICRO SD CARD AND RESET BUTTON
11RJ-45RJ-45 Data ConnectionData Connection
22DC12VDC12V Power ConnectionPower Connection
33Audio I/OAudio I/O
GroundGround
Audio InAudio In
Audio OutAudio Out
11Reset ButtonReset Button
To restore the camera to factory defaults:To restore the camera to factory defaults:
1. Disconnect power for 30 seconds.
2. Reconnect power and wait 30 seconds.
3. Press and hold the reset button for 20 seconds.
22MicroSD Card SlotMicroSD Card Slot
Supports up to 512GB microSD card for Edge storage.Supports up to 512GB microSD card for Edge storage.
Do not add or remove the microSD card when the camera isDo not add or remove the microSD card when the camera is
powered on.powered on.
12
SET THE DEFAULT
CAMERA PASSWORD
Scan the QR code or follow the
link below to learn how to change
the default camera passwords
used on initial setup.
avertx.com/default-camera-
4K INDOOR/OUTDOOR IP DOME
WITH SMART ANALYTICS

Copyright © 2021 AvertX. All rights reserved. Information contained in this document is subject to change without prior notice. AvertX does its best to provide accurate information, but cannot be held responsible for typos or mistakes.
CONNECTING TO THE CAMERA
This camera is plug and play when connected to an AvertX ProConnect
Recorder. To access this camera without an AvertX recorder, you will need
to connect the camera to a Power Over Ethernet Switch and install AvertX
Network Camera Manager Software on a Windows computer.
1. Download and install the Camera Finder software at https://www.avertx.
com/downloads/
2. When the camera is found, click “Load” under the web page. The camera
admin page will load in a browser.
3. Login to the camera using the username admin. The rst time the camera is
accessed you will need to set a password.
4. AvertX cameras are set to DHCP by default. If a DHCP server is
not detected after 2 minutes, the camera will default to IP address
192.168.51.2.
37716AA
DEFAULT USERNAME & PASSWORD
Default Username: admin
Note: All AvertX IP cameras ship without a default password.
The admin user password can be set using the following methods:
1. AvertX recorders running software version 2.1 or newer will automatically
set a new unique password if:
• Connected to a ProConnect recorder with a built-in PoE switch.
2. Connected to a network switch through the camera network port and se-
lected then added in setup, if a new password has not already been set.
3. Connect to the camera directly through a Web Browser and follow the
onscreen prompts.
4. Use the Network Camera Manager (NCM) Utility.
INSTALLATION
1. Apply template sticker to desired camera location.
2. Drill anchor holes and 7/8” hole for cabling using included mounting
template.
Note: The 7/8” cabling hole is not required if a mounting accessory is
being used.
3. Remove mounting template.
4. Insert anchors.
5. Connect network cable with included waterproof cable connector.
The HD848IRM camera can be installed onto a wall or the ceiling. Be sure that
the structure is strong enough to support the camera. Pay careful attention to
orientation when mounting. On the bottom of the camera, the word “FRONT”
is embossed on the camera to show proper orientation. “LOGO DIRECTION”
is marked with an arrow on the mounting template to correspond with the
“FRONT” on the camera.
6. Remove the camera dome cover by removing 3 dome screws and lifting.
AUTOFOCUS ZOOM LENS
The HD848IRM Dome Camera is equipped with an Auto Focus Zoom lens.
Do not attempt to manually focus this camera. Activating the zoom will focus
the camera.
To activate zoom and focus the camera: In Live view, right click on the
desired camera pane and select zoom in. Right-click and zoom out when the
camera nishes focusing.
Attach To Surface
7. Attach the camera to the ceiling or wall with
the included screws.
8. Adjust the camera to the desired angle.
• The HD848IRM features 3-axis camera
positioning: Tilt, Camera Rotation, and
Lens Rotation.
• Rotate the lens so the 0 mark is vertical
relative to the horizon.
Note: Use the AvertXConnect app to view
the camera while adjusting view.
9. Replace the dome cover. To install, align
screws to the holes. Tighten dome cover
screws just enough for a good seal. Clean
the dome with the included cleaning cloth.
10. Mount camera.
11. Install the camera cover and tighten the
lock screw.
Adjust View
For more information on installing your AvertX camera, download the user manual,
read FAQs and DIY recources, and view instructional videos at www.avertx.com.