avertX HD428 User manual

This guide is a quick reference for users to install and operate HD428 Night
Vision HD Indoor/Outdoor Bullet Cameras. It provides only basic information
regarding installation and operation of your camera. For further details,
please refer to the HD428 User Manual.
Before proceeding, please check to conrm that the box contains the items
listed here. If any item is missing or has defects, DO NOT install or operate
the product and contact AvertX for assistance.
ABOUT THIS GUIDE
CONTENTS OF CAMERA BOX
HD428 Bullet Camera Waterproof Cable
Connector
Documents
HD428 QUICK START GUIDE
Screws
Anchors
The HD428 camera can be installed directly
onto a wall or ceiling. Be sure that the structure
is strong enough to support the camera.
1. Remove the HD428 camera from the
packaging.
2. Connect the camera cable from the
ceiling or wall to the dongle on the
camera. If using the waterproof cable
connector, attach it now. See instructions
on reverse.
3. Loosen the locknut and/or adjustment
screws on the camera bracket. Aim the
camera down to access screw holes
4. A󰀩x the camera base to the ceiling
or wall with the included self-tapping
screws. When mounting on an outdoor
wall, the cable notch should be
positioned downward.
5. Adjust the position of your camera. Be
careful not to damage the cable when
moving the camera.
6. Tighten the locknut and screws to secure
your camera.
Note:
The HD428 mini bullet camera is pre-
focused and factory sealed. There is no need
to open the camera housing.
If mounting outside, seal the opening at the
wall and the base of the camera with silicone
caulking.
Improper installation may cause damage to
your camera and void the warranty.
INSTALLATION
4K MINI IP BULLET
INDOOR/OUTDOOR
WITH NIGHT VISION
Align Holes
Adjust Aim
36772AA

Copyright © 2018 AvertX. All rights reserved. Information contained in this document is subject
to change without prior notice. AvertX does its best to provide accurate information, but cannot be
held responsible for typos or mistakes.
NETWORK CABLE INSTALLATION
A 100’ Cat5e non-plenum UTP camera cable is included with your camera. It
is important to consider how the network cable is attached to the camera.
• If passing the cord through a wall or ceiling, drill a 7/8” hole.
• For outdoor installations, ensure the connection between your network
cable and the camera jack is housed within a wall or indoors or use the
waterproof cable connector. If this is not possible, a waterproof junction
box mount is available at avertx.com
• For outdoor installations, use silicone caulking to seal any holes in the
wall or ceiling to protect against leaks.
• If your installation is in a commercial building, consult local re codes.
Plenum rated cable may be required.
WATERPROOF CABLE CONNECTOR
This camera features an IP66-rated waterproof cable connector for
unprotected outdoor connections.
• Slide all pieces of the waterproof cable connector over the cable plug in this
order:
1. Small plastic ring
2. Flexible silicone seal ring. You will need to stretch the silicone seal
over the RJ-45 plug.
3. Large plastic ring
• Slide the rubber “O” ring over the camera plug screw and connect the
camera cable to the plug on the dongle. Screw the large plastic ring into
the dongle.
• Insert the exible silicone seal into the “crown” section of the large plastic
ring
• Screw the small plastic ring into the large plastic ring
1-855-2AVERTX (1-855-228-3789)
www.avertx.com
CONNECTING TO THE CAMERA
If you are using this camera with an AvertX recorder, follow the instructions
in the recorder user manual to connect to your camera. You can also set up
your camera using your PC.
1. Type the IP address 192.168.0.250 in the address bar of your browser
2. Viewer software may need to be installed on your PC the rst time you
connect to the camera. Download and install the viewer software when
prompted.
3. Supported browsers: Chrome, Firefox, Edge, Internet Explorer. Please
consult the user manual for additional browser support.
USERNAME AND PASSWORD
The username and password are case sensitive. AvertX strongly recommends
changing the password after the initial setup to prevent unauthorized access to
the camera.
Username – admin
Password – 1234
RESET BUTTON
Your HD428 camera is equipped with a reset button to return the camera to
factory default settings, if necessary. To reset your camera, power cycle the
camera then push and hold the reset button for 15 seconds. This has to be
performed within 10 min after the camera has been powered on or the reset
will fail.
For more information on installing your AvertX camera, see the user manual
or view instructional videos at avertx.com/videos.
FOR FURTHER INSTRUCTIONS:
36772AA
Reset button