avertX HD448IR User manual

This guide is a quick reference for users to install and operate the HD448IR
Night Vision HD Indoor/Outdoor Bullet Cameras. It provides only basic
information regarding installation and operation of your camera. For further
details, please download the HD448IR User Manual at www.avertx.com.
Before proceeding, please check to conrm that the box contains the items
listed here. Do not install or operate the product if any item is missing or has
defects; contact AvertX for assistance.
ABOUT THIS GUIDE
CONTENTS OF CAMERA BOX
HD448IR Bullet Waterproof Cable
Connector
Documents
HD448IR QUICK START GUIDE
Screws
Anchors
The HD448IR camera can be installed directly
onto a wall or ceiling. Be sure that the structure is
strong enough to support the camera.
1. Use the included mounting template to
pre-drill holes for the mounting screws and,
if passing the cable through the ceiling or
wall, drill a 7/8” hole.
2. Thread your Cat5e camera cable through
the waterproof cable connector and connect
to the camera dongle. See reverse page for
instructions on waterproof cable connector.
3. Loosen the locknut on the camera bracket.
Aim the camera down to access screw
holes
4. Attach the camera base to the ceiling
or wall with the included screws. When
mounting on an outdoor wall, the cable
notch should be positioned downward.
5. Adjust the position of your camera.
TIP: Use the AvertX Connect app to view
the camera while adjusting view.
6. Tighten the locknut to secure your camera.
Note:
The HD448IR mini bullet camera is pre-focused
and factory sealed. There is no need to open
the camera housing.
If mounting outside, seal the opening at the wall
and the base of the camera with silicone caulking.
Improper installation may cause damage to
your camera and void the warranty.
INSTALLATION
4K OUTDOOR MINI IP BULLET
WITH SMART ANALYTICS
Align Holes
Adjust View
37501AA
Mounting accessories for this camera are available at avertx.com.

Copyright © 2020 AvertX. All rights reserved. Information contained in this document is subject
to change without prior notice. AvertX does its best to provide accurate information, but cannot be
held responsible for typos or mistakes.
NETWORK CABLE INSTALLATION
A 100’ Cat5e non-plenum UTP camera cable is included with your camera. It
is important to consider how the network cable is attached to the camera.
• If passing the cord through a wall or ceiling, drill a 7/8” hole.
• We recommend using the waterproof cable connector on all installations.
• For maximum weather and tamper resistance in outdoor installations,
place the connection between your camera cable and the camera jack
within a wall or use a junction box available at avertx.com.
• For outdoor installations, use silicone caulking to seal any holes in the
wall or ceiling to protect against leaks.
• If your installation is in a commercial building, consult local re codes.
Plenum rated cable may be required.
WATERPROOF CABLE CONNECTOR
To use the IP66-rated waterproof cable connector:
You do not need to re-terminate the cable to use the waterproof cable
connector.
• Slide all pieces of the waterproof cable connector over the cable plug in this
order:
1. Small plastic ring
2. Flexible silicone seal ring. You will need to stretch the silicone seal
over the RJ-45 plug.
3. Large plastic ring
• Slide the rubber “O” ring over the camera plug screw and connect the
camera cable to the plug on the dongle. Screw the large plastic ring into
the dongle.
• Insert the exible silicone seal into the “crown” section of the large plastic
ring
• Screw the small plastic ring into the large plastic ring
CONNECTING TO THE CAMERA
This camera is plug and play when connected to an AvertX ProConnect
Recorder. To access this camera without an AvertX recorder, you will need
to connect the camera to a Power Over Ethernet Switch and install AvertX
Network Camera Manager Software on a Windows computer.
1. Download and install the Camera Finder software at www.avertx.com/
downloads/.
2. When the camera is found, click “Load” under the web page. The camera
admin page will load in a browser.
3. Login to the camera using the username admin. The rst time the camera is
accessed you will need to set a password.
4. AvertX cameras are set to DHCP by default. If a DHCP server is
not detected after 2 minutes, the camera will default to IP address
192.168.51.2.
MICRO SD CARD AND RESET BUTTON
Your camera is equipped with a slot for a microSD card and a Reset button.
To access these, you must remove the microSD / Reset cover.
If you have purchased a microSD card to be used for backup, insert the
formatted card into the slot. Refer to the user manual for compatible cards
and how to properly format your microSD Card.
Use the reset button to restore the factory default settings. To reset your
camera:
1. Disconnect the cat5e cable from the camera for 30 seconds.
2. Hold the reset button down while reconnecting cat5e.
3. The IR lights will illuminate when power is reconnected; continue holding
the reset button until the IR lights turn o󰀨 (approximately 30 seconds).
4. Allow 2 minutes before attempting to rediscover camera.
37501AA
Reset button
microSD slot
Contact AvertX Support: 1-855-228-3789 | www.avertx.com
For more information on installing your AvertX camera, download the
user manual, read FAQs and DIY resources, and view instructional videos
at www.avertx.com.
FOR FURTHER INSTRUCTIONS: