Avery Weigh-Tronix 2060 User manual

Model 2060
Universal Weight Indicator
User Instructions
AWT35-501506
Issue AB

Model 2060_u_en_501506.book
Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies whose ultimate parent company is
Illinois Tool Works Inc (“Illinois Tool Works”). Copyright © 2018 Illinois Tool Works. All rights reserved.
No part of this publication may be reproduced by making a facsimile copy, by the making of a copy in three dimensions of a two-dimensional
work and the making of a copy in two dimensions of a three-dimensional work, stored in any medium by electronic means, or transmitted in
any form or by any means, including electronic, mechanical, broadcasting, recording or otherwise without the prior written consent of the
copyright owner, under license, or as permitted by law.
This publication was correct at the time of going to print, however Avery Weigh-Tronix reserves the right to alter without notice the
specification, design, price or conditions of supply of any product or service at any time.

Model 2060 User Instructions 3
Table of Contents
Chapter 1 General Information and Warnings ........................................................................................7
About this Manual ..............................................................................................................7
Text Conventions ........................................................................................................7
Special Messages .......................................................................................................7
Installation ..........................................................................................................................8
Safe Handling of Equipment with Batteries .................................................................8
Routine Maintenance .........................................................................................................9
Cleaning the Machine ........................................................................................................9
Training ..............................................................................................................................9
Sharp Objects ..................................................................................................................10
FCC and EMC Declarations of Compliance .....................................................................10
Declaration of Conformity ................................................................................................11
Chapter 2 Overview .................................................................................................................................12
Front Panel and Keys ......................................................................................................12
Front Panel Keys .......................................................................................................13
Home Screen ...................................................................................................................14
Adjusting screen contrast .................................................................................................14
Using the alphanumeric keypad .......................................................................................14
Menus ..............................................................................................................................14
Standard Print Formats ....................................................................................................15
Chapter 3 Installation ..............................................................................................................................17
Mounting the Model 2060 ................................................................................................17
Instructions for V mount ............................................................................................17
Instruction for Ram Mount .........................................................................................17
Cable Connections and Power Requirements .................................................................18
AWT05-509201 4+ Pin Amp Bottom Plate ................................................................18
AWT05-509202 4x 5Pin AWT Bottom Plate ..............................................................18
Connectors ................................................................................................................19
Routing the Scale Interface Cable ...................................................................................20
Connecting to a Convenience Outlet ...............................................................................20
Power Connections - Battery ...........................................................................................21
Wiring 2060 Indicator to Equipment Power Systems .......................................................23
12 Volt Power Systems (one and two 12 V batteries) ...............................................23
24 Volt Power Systems .............................................................................................24
Grounded Power Systems ........................................................................................24
Power Connections - AC ..................................................................................................25
Optional Communications Connections ...........................................................................26
Additional Connectors ...............................................................................................27
I/O Connector Pins (9 pin connector) ........................................................................27
Chapter 4 Quick Start Calibration Guide ...............................................................................................28
Calibrate the 2060 with a Standard Configuration Number .............................................28
Determine the Configuration Number ........................................................................28
Configuration Codes ..................................................................................................30
Enter the Configuration Code Number Parameter (Cfg Num) ...................................31
Configuration Code Numbers for Common Applications: ..........................................32
Custom Configuration Number for AWTX Weigh Bars ....................................................33
Determine Configuration Number ..............................................................................33
Determine Custom Calibration Number ....................................................................34
Custom Number Table ..............................................................................................34
Enter Configuration Code Number (Cfg Num) ..........................................................38
Enter Custom Configuration Number (Cust.Cfg) .......................................................38
Custom Configuration Number Calibration ................................................................39

4 Model 2060 User Instructions
Configuring the 2060 for Other Brand Weigh Bars and Loadcells ...................................40
Custom Calibration Number ......................................................................................40
Chapter 5 Menus ......................................................................................................................................42
Accessing the menus .......................................................................................................42
Menu Navigation ......................................................................................................43
Exiting the Menus ............................................................................................................43
User menu .......................................................................................................................45
The User submenu ....................................................................................................45
The About submenu ..................................................................................................46
The Audit submenu ...................................................................................................47
Diag menu ........................................................................................................................48
Scale .........................................................................................................................48
Cur.Zero ....................................................................................................................48
Display .......................................................................................................................49
Buttons ......................................................................................................................49
Ports ..........................................................................................................................49
Inputs .........................................................................................................................49
Outputs ......................................................................................................................50
Options ......................................................................................................................50
Logs ...........................................................................................................................51
BSQ ...........................................................................................................................51
DigJbox .....................................................................................................................51
Admin menu .....................................................................................................................52
Calibrate ...........................................................................................................................54
Zero procedure ..........................................................................................................54
Span procedure .........................................................................................................55
Linearity (Linear) procedure ......................................................................................56
Build Up procedure ....................................................................................................56
Input procedure (key-in calibration) ...........................................................................56
Gravity procedure ......................................................................................................57
Display procedure .....................................................................................................57
Cal Unit procedure ....................................................................................................57
Print procedure ..........................................................................................................58
Cfg Num ....................................................................................................................58
Cust.Cfg ....................................................................................................................58
Span Adj ....................................................................................................................58
Scale menu ......................................................................................................................58
Capacty .....................................................................................................................59
Dvision .....................................................................................................................59
Units ..........................................................................................................................59
Stable ........................................................................................................................60
AZT ............................................................................................................................60
Filter ..........................................................................................................................60
Ranges ......................................................................................................................62
2,3 Range ..................................................................................................................62
Type ..........................................................................................................................64
Roc ............................................................................................................................64
DigJbox .....................................................................................................................64
Traffic ........................................................................................................................64
System menu ...................................................................................................................65
Site ............................................................................................................................65
Display .......................................................................................................................66
Buttons ......................................................................................................................67
D-Vals ........................................................................................................................67
Tare ...........................................................................................................................69
Config ........................................................................................................................69

Model 2060 User Instructions 5
Archive ......................................................................................................................70
Serial .........................................................................................................................70
Update .......................................................................................................................70
Password ...................................................................................................................71
Z-Lock .......................................................................................................................71
Beeper .......................................................................................................................71
Num Scl .....................................................................................................................71
Ports menu .......................................................................................................................72
Serial .........................................................................................................................72
Enet ...........................................................................................................................73
Protcl .........................................................................................................................75
P.F. Edit .....................................................................................................................77
PLC ...........................................................................................................................77
Printer ........................................................................................................................79
File .............................................................................................................................79
Options ......................................................................................................................81
Opt232 .......................................................................................................................81
USB ...........................................................................................................................81
Chapter 6 Application menu ...................................................................................................................82
Accessing the Application menu ......................................................................................83
Auto Settings ....................................................................................................................84
Totals Settings .................................................................................................................85
App Settings .....................................................................................................................85
App Info ............................................................................................................................86

6 Model 2060 User Instructions

Model 2060 User Instructions 7
1 General Information and Warnings
1.1 About this Manual
This manual is divided into chapters by the chapter number and the large text at the top of a page. Subsections
are labeled using the 1.1 and 1.1.1 convention. The names of the chapter and the next subsection level appear
at the top of alternating pages of the manual to remind you of where you are in the manual. The manual name
and page numbers appear at the bottom of the pages.
1.1.1 Text Conventions
Key names are shown in bold and reflect the case of the key being described. If a key has dual functions, the
function is shown first followed by the key name in parentheses and in bold, such as in these examples: F1,
SELECT, PRINT, etc.
Displayed messages appear in bold italic type and reflect the case of the displayed message.
1.1.2 Special Messages
Examples of special messages you will see in this manual are defined below. The heading words have specific
meanings to alert you to additional information or the relative level of hazard.
DANGER!
THIS IS A DANGER SYMBOL.
DANGER MEANS THAT FAILURE TO FOLLOW SPECIFIC PRACTICES
OR PROCEDURES WILL CAUSE INJURY OR DEATH.
ELECTRICAL WARNING!
THIS IS AN ELECTRICAL WARNING SYMBOL.
ELECTRICAL WARNINGS MEAN THAT FAILURE TO FOLLOW
SPECIFIC PRACTICES OR PROCEDURES MAY RESULT IN
ELECTROCUTION, ARC BURNS, EXPLOSIONS OR OTHER HAZARDS
THAT MAY CAUSE INJURY OR DEATH.
WARNING!
This is a Warning symbol.
Warnings mean that failure to follow specific practices and procedures may
have major consequences such as injury or death.
CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result
in damage to equipment or corruption to and loss of data.

8 Model 2060 User Instructions
1.2 Installation
1.2.1 Safe Handling of Equipment with Batteries
NOTE: This is a Note symbol. Notes give additional and important information, hints
and tips that help you to use your product.
NO USER SERVICEABLE PARTS. REFER TO QUALIFIED SERVICE
PERSONNEL FOR SERVICE.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s instructions.
ATTENTION: Il y a danger d'explosion s'il y a remplacement incorrect de la
batterie, remplacer uniquement avec une batterie du même type ou d'un type
équivalent recommandé par le constructeur. Mettre au rebut les batteries
usagées conformément aux instructions du fabricant.

Model 2060 User Instructions 9
1.3 Routine Maintenance
1.4 Cleaning the Machine
1.5 Training
Do not attempt to operate or complete any procedure on a machine unless you have received the appropriate
training or read the instruction books.
To avoid the risk of RSI (Repetitive Strain Injury), place the machine on a surface which is ergonomically
satisfactory to the user. Take frequent breaks during prolonged usage.
IMPORTANT: This equipment must be routinely checked for proper operation
and calibration.
Application and usage will determine the frequency of calibration required for
safe operation.
ELECTRICAL WARNING!
ALWAYS TURN OFF THE MACHINE AND ISOLATE FROM THE POWER
SUPPLY BEFORE STARTING ANY ROUTINE MAINTENANCE TO
AVOID THE POSSIBILITY OF ELECTRIC SHOCK.
CAUTION: Do not weld on or near the 3060 or any part of the scale system such
as Weigh Bars. Excessive heat and / or high currents may cause internal
damage. Physically remove the 2060 from any equipment it is mounted to and
disconnect it from the power source. Make ground connection as far away from
any scale part (cables, Weigh Bar, etc.) as possible.
Table 1.1 Cleaning DOs and DON’Ts
DO DO NOT
Wipedowntheoutsideofstandardproducts
withacleancloth,moistenedwithwaterand
a small amount of mild detergent
Attempt to clean the inside of the machine
Use harsh abrasives, solvents, scouring cleaners or
alkaline cleaning solutions
Spray the cloth when using a proprietary
cleaning fluid Spray any liquid directly on to the display windows

10 Model 2060 User Instructions
1.6 Sharp Objects
Do not use sharp objects such as screwdrivers to operate the keys.
1.7 FCC and EMC Declarations of Compliance
United States
Canada
European Countries
This equipment has been testedand found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
la Classe A prescrites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des Communications du Canada.
WARNING: This is a Class A product.Inadomesticenvironment,this product may causeradiointerferenceinwhichtheusermaybe
required to take adequate measures.

Model 2060 User Instructions 11
1.8 Declaration of Conformity
EN
EU
Declaration of
Conformity
Name and address of the manufacturer: Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP ENGLAND This declaration of conformity is issued under the sole responsibility of the manufacturer Object of the declaration:
2060 / M2060 RD60M RCV60-CE
The object of the declaration described above is in conformi- ty with the relevant Union harmonisation legislation:
Applicable Directives Harmonised
standards or other technical specifications
Additional information: Note
1
:

ITW Ltd trading as Avery Weigh-Tronix
Reg. Office: Nexus House, Station Road, Egham, Surrey, TW20 9LB, England
 Signed for and on behalf of: Avery Weigh-Tronix at 1000 Armstrong Drive, Fairmont, MN, 56031-1439, USA on 2017-05-08 K.Detert
Global Head of R&D
Model/Type:
2060/RD60/RCV60-CE
2014/30/EU
Electromagnetic Compatibility
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/EU
Electrical equipment designed for use
within certain voltage limits
EN 60950–1 : 2006
+A2:2013
76501-556 Issue
2
DE
EU-
Konformitätserklärung 
Name und Anschrift des Herstellers: Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP ENGLAND Die alleinige Verantwortung für die Ausstellung dieser Kon- formitätserklärung trägt der Hersteller. Gegenstand der Erklärung:
2060 / M2060 RD60M RCV60-CE
Der oben beschriebene Gegenstand der Erklärung erfüllt die einschlägigen Harmonisierungsrechtsvorschriften der Union:
Angewandte Richtlinien Harmonisierte
Normen oder sonstigen technischen Spezifikationen
Zusatzangaben: Anmerkung 1:
ITW Ltd Handel als Avery Weigh-Tronix
Sitz: Nexus House, Station Road, Egham, Surrey, TW20 9LB, England
Unterzeichnet für und im Namen von: Avery Weigh-Tronix bei 1000 Armstrong Drive, Fairmont, MN, 56031-1439, USA am 2017-05-08 K.Detert
Globaler Leiter von Forschung und Entwicklung
Modell / Typen:
2060/RD60/RCV60-CE
2014/30/EU
Elektromagnetische Verträglichkeit
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/EU
Elektrischer Betriebsmittel zur
Verwendung innerhalb bestimmter
Spanungsgrenzen
EN 60950–1 : 2006
+A2:2013
FR
DéclaraƟonUE
de
Conformité
Nom et adresse du fabricant : Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP ANGLETERRE La présente déclaration de conformité est établie sous la seule responsabilité du fabricant. Objet de la declaration:
2060 / M2060 RD60M RCV60-CE
L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable:
Les directives en vigueur Les normes
harmonisées ou d’autres spécifications techniques
Informations complémentaires: Nota 1:
ITW Ltd exerçant également sous le nom de Avery Weigh- Tronix
Siège social: Nexus House, Station Road, Egham, Surrey, TW20 9LB, Angleterre
Signé par et au nom de: Avery Weigh-Tronix à 1000 Armstrong Drive, Fairmont, MN, 56031-1439, USA le 2017-05-08 K.Detert
Responsable Mondial de la Recherche et du Développement
Modèle / Type:
2060/RD60/RCV60-CE
2014/30/UE
Compatibilité Électromagnétique
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/UE
Matériel électrique destiné à être
employé dans certaines limites de
tension
EN 60950–1 : 2006
+A2:2013
NL
EU-
Conformiteitsverklar-
ing
Naam en adres van de fabrikant : Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP ENGELAND Deze conformiteitsverklaring wordt verstrekt onder volledige verantwoordelijkheid van de fabrikant. Voorwerp van de verklaring:
2060 / M2060 RD60M RCV60-CE
Het hierboven beschreven voorwerp is in overeenstemming met de desbetreffende harmonisatiewetgeving van de Unie:
Toepasselijke richtlijnen Geharmoniseerde
standaarden of andere technische specificaties
Aanvullende informatie: Noot
1
:

ITW Ltd trading als Avery Weigh-Tronix
Zetel: Nexus House, Station Road, Egham, Surrey, TW20 9LB, England
Ondertekend voor en namens: Avery Weigh-Tronix bij 1000 Armstrong Drive, Fairmont, MN, 56031-1439, VS op 2017-05-08 K.Detert
Wereldwijd Hoofd van Onderzoek en Ontwikkeling
Model/Type:
2060/RD60/RCV60-CE
2014/30/EU
Elektromagnetische compatibiliteit
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/EU
Elektrisch materiaal bestemd voor
gebruik binnen bepaalde span-
ningsgrenzen
EN 60950–1 : 2006
+A2:2013
IT
Dichiarazione
di
Conformità UE
Nome e indirizzo del fabbricante: Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP INGHILTERRA La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva del fabbricante. Oggetto della dichiarazione:
2060 / M2060 RD60M RCV60-CE
L’oggetto della dichiarazione di cui sopra è conforme alla pertinente normativa di armonizzazione dell’Unione:
Direttive applicabili Armonizzato
standard o altre specificazioni tecniche
Informazioni supplementari: Nota 1:
ITW Ltd trading come Avery Weigh-Tronix
Sede dell'ufficio: Nexus House, Station Road, Egham, Surrey, TW20 9LB, England
Firmato a nome e per conto di: Avery Weigh-Tronix a 1000 Armstrong Drive, Fairmont, MN, 56031-1439, U.S.A. su 2017-05-08 K.Detert
Responsabile Globale della Ricerca e Sviluppo
Modello / Tipo:
2060/RD60/RCV60-CE
2014/30/UE
Compatibilità elettromagnetica
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/UE
Materiale elettrico destinato a essere
adoperato entro taluni limiti di ten-
sione
EN 60950–1 : 2006
+A2:2013
ES
DeclaraciónUE
de
Conformidad
Nombre y dirección del fabricante Avery Weigh-Tronix1
Foundry Lane Smethwick West Midlands B66 2LP INGLATERRA La presente declaración de conformidad se expide bajo la exclusiva responsabilidad del fabricante. Objeto de la declaración:
2060 / M2060 RD60M RCV60-CE
El objeto de la declaración descrita anteriormente es conforme con la legislación de armonización pertinente de la Unión:
Directivas aplicables Normas
armonizadas u otras especificaciones técnicas
Información adicional: Nota1:
ITW Ltd trading as Avery Weigh-Tronix
Oficina registrada: Nexus House, Station Road, Egham, Surrey, TW20 9LB, Angleterre
Firmado en nombre de: Avery Weigh-Tronix en 1000 Armstrong Drive, Fairmont, MN, 56031-1439, EE.UU el 2017-05-08 K.Detert
Jefe Global de Investigación y Desarrollo
Modelo / Tipo:
2060/RD60/RCV60-CE
2014/30/UE
Compatibilidad electromagnética
EN61000-6-1:2007 EN61000-6-4:2007 EN14982:2009
2014/35/UE
Material eléctrico destinado a utiliz-
arse con determinados límites de
tensión
EN 60950–1 : 2006
+A2:2013

Model 2060 User Instructions 12
2Overview
This manual covers the installation, connections and configuration of the Model 2060
indicator.
The 2060 can connect to USB flash drives, printers, remote displays, computers and
other peripheral devices.
Communications- Two standard RS-232 with optional third bi-directional serial ports
w/selectable output formats – Standard, Broadcast, Transfer Data Module (TDM).
Standard Connectivity - USB 9-pin Amp Input/Output Connector.
Optional Connectivity- Internal WiFi, Internal ZigBee point to point wireless, RM 110
Bluetooth, RS 232 peripheral interface, Ethernet Transmitter/Receiver, Third RS-232
Port.
TTL Inputs- Three programmable inputs (Std, Zero Clear, Hold, or Print).
Outputs- Two setpoint outputs, open collector design.
2.1 Front Panel and Keys
Figure 2.1 2060 Front Panel
Press the Power key to turn the unit on and press and hold the key for three seconds
to turn the unit off. The display will ask if you are sure. Use the up and down arrow keys
to highlight your answer and press the Enter (F3) key to confirm.
2060
1 2
ABC 3 DEF
4
GHI 5 JKLJKL 6 MNO
7
PQRS 8 TUV 9 WXYZ
CLEAR 0-#:,%
F1 F2 F3 F4 F5
HOLD
TARE ZEROPRINT
HOMEHOLDHOLD
GROSS/NET
BACK ENTER
Power key

Model 2060 User Instructions 13
2.1.1 Front Panel Keys
The 2060 front panel shown in Figure 2.1 consists of the keys and the display.
The functions of each key on the front panel are listed below.
Never press a key with anything but your finger. Damage to the overlay may result if
sharp or rough objects are used.
Press to perform a tare function or prompts for a keyboard
tare, if enabled.
Press to toggle between Gross, Net, Tare and any other
active display values.
Press to send information to a peripheral device (printer,
computer or other serial device module).
Pressinanymodetoreturntohome screen or hold down for
3 seconds to access password screen.
Zeros the scale.
Press to back up one screen.
Press to hold a weight.
Press to toggle between the Gross and Net weight.
F1 - F5 Press these keys to select application specific choices.
Use the numeric keypad to enter numbers and letters in the
appropriate screens. Press the CLEAR key to clear the last
entry.
TARE
ENTER
PRINT
HOME
ZERO
BACK
HOLD
HOLDHOLD
GROSS/NET
1 2
ABC
3
DEF
4
GHI
5
JKL
JKL
6
MNO
7 8
TUV
9
CLEAR
0

14 Model 2060 User Instructions
2.2 Home Screen
Figure 2.2 Home Screen
The home screen has two softkeys, explained below:
RM (F1) Press this key to access a memory channel, so the indicator is ready for
accumulations into that channel.
M+ (F5) Press this key to accumulate weights in the active memory channel.
2.3 Adjusting screen contrast
To decrease the screen contrast press and hold the HOLD key and repeatedly press
the TARE key. To increase the contrast, press and hold the HOLD key and repeatedly
press the ENTER key.
2.4 Using the alphanumeric keypad
Use the alphanumeric keypad to enter numbers and words when prompted by the
indicator. The action is similar to using a cell phone to select the number or letter. A
rapid succession of presses will scroll through the number on the key and then the
letters, starting with upper case and then lower case. The decimal key scrolls through
the negative sign, pound sign, colon, comma and percent sign. The 0 key toggles
between 0 and a space.
2.5 Menus
Menus used to configure the 2060 are accessed with passwords. See Menus on page
42 for a complete overview of each menu and how to navigate through them.

Model 2060 User Instructions 15
2.6 Standard Print Formats
The Model 2060 has 10 available print formats. See the examples below.
Format 0
Format 1
Format 2
Format 3 (default)
Format 4
G: 32010 lb
G: 32010 lb
T: 16010 lb
N: 16000 lb
04-26-2006
03:02:47
G: 32010 lb
04-26-2006
03:02:47
G: 32010 lb
T: 16010 lb
N: 16000 lb
32010

16 Model 2060 User Instructions
Format 5
Format 6
Format 7
Format 8
Format 9
32010 ,16010 ,16000
04-26-2006,03:02:47, 32010
04-26-2006,03:02:47, 32010 ,
16010 , 1600
N: 16000 lb
04-26-2006
03:02:47
N: 16000 lb

Model 2060 User Instructions 17
3 Installation
The following section will cover installing the Model 2060 and cable connections.
3.1 Mounting the Model 2060
The Model 2060 mounts on a quick-detach V bracket or a 1.5" Ram Mount.
3.1.1 Instructions for V mount
Weld or bolt the quick-detach bracket into place, as follows:
1. Choose a mounting location that is
lconvenient for operation of the indicator, and
lprotected from moving parts or from other moving machinery
2. Hold the indicator at the proposed mounting location, and verify that the
display is legible and the controls accessible.
3. Position the quick-detach bracket with the wider end at the top, mark the
desired mounting location. If bolting, use the quick-detach bracket as a
template and mark and drill holes.
4. Weld or bolt the quick-detach bracket at the appropriate location. If bolting,
use double nuts or self-locking nuts to protect both indicator and machinery.
CAUTION: Do not weld on or near a Weigh Bar. Excessive heat or high
currents may cause internal damage.
5. Insert the indicator bracket into the quick-detach bracket and push it down into
place.
6. For mobile applications, wrap and twist a strong wire or zip tie around the
indicator bracket and the quick-detach bracket to stabilize the mounting.
3.1.2 Instruction for Ram Mount
1. Order the Ram Mount Kit PN AWT05-508626.
2. Take nuts holding V bracket on 2060 off.

18 Model 2060 User Instructions
3. Bolt one of the 2.5" Ram Mount bases onto the 2060 V mount bracket. It is
recommend to bolt the Ram mount onto the Bracket so the V part of the
bracket will point towards the 2060 (reverse of how the bracket would be
mounted to use as a V mount).
3.2 Cable Connections and Power Requirements
Voltage to the Model 2060 must be 10-36 volts DC, negative ground only. Dropping
below eight volts will cause the Model 2060 to automatically shut itself off, protecting
the battery from being completely drained.
3.2.1 AWT05-509201 4+ Pin Amp Bottom Plate
This model has 4-pin power, Input/Output, printer, remote display and J-box home run
cable connector.
3.2.2 AWT05-509202 4x 5Pin AWT Bottom Plate
This model has 2-pin power, Input/Output, printer, remote display and input for 4
different weigh bars or J-box home run cable connector.
4-pin Power Input I/O Connector 4-pin AMP J-box
Interface
Com-2
Default
Printer
Com-1
Default
Remote
Display
Com-2
Default
Printer
Com-1
Default
Remote
Display
2-pin Power Input
I/O Connector
4 Weigh Bars
Full Bridge
W/O J-box

Model 2060 User Instructions 19
3.2.3 Connectors
RS-232 Port
Pin Description
1N/C
2XMT
3N/C
4RXD
5GND
6GND
7+5V
8+10-36V
Outside View
(Male)
12
3
6
47
8
5
4-Pin Power Input
Pin Description
1 +12V Input
2GND
3N/C
4N/C
Outside View
(Male)
1
2
3
4
1
2
43
4-Pin Amp J-Box Interface
Pin Description
1+Excitation
2-Bridge
3+Bridge
4-Excitation
Outside View
(Female)
1
2
34
2-Pin Power Input
Pin Description
A+12V
BGND
Outside View
(Female)
AB
5-Pin Weigh Bar Input
Pin Description
A - Bridge
B + Excitation
C+Bridge
D - Excitation
EShield
Outside View
(Female)
A
E
DC
B
I/O Connector (9 pin)
Pin Description
1+12V
2+5V
3GND
4 Input 2 (ZERO)
5 Input 3 (RESET target)
6GND
7 Output 1
8 Output 2 (N.O)
9 Input 1 (TARE)
Outside View
(Male)
1
23
4
5
6
79
8

20 Model 2060 User Instructions
3.3 Routing the Scale Interface Cable
The scale interface cable is the cable that runs from the junction box (j-box) to the
indicator.
1. Loosely connect the scale interface cable to the SCALE connector on the
indicator.
Figure 3.1 Scale Connector
2. Run the cable from the indicator to the junction box, allowing some slack in the
cable.
3. Connect the other end of the scale interface cable to the junction box.
4. Inspect the cable run and make sure that the cable is not pinched, kinked or in
the way of moving parts or sharp objects.
5. Be sure to allow some slack when zip tyeing or tucking away the cable.
6. Tighten the connector at the indicator.
3.4 Connecting to a Convenience Outlet
If the equipment you are using has an Auxiliary Power Outlet Strip it is preferred to
supply power to the indicator from the outlet strip rather than the battery.
Most power strip outlets have spades that provide constant power (unswitched power)
or key-switched power. Decide which one works best for your application and identify
which spades provide this power type.
If you have a tinned lead power supply and want to connect to the auxiliary power you
need to add a spade to each wire.
lConnect the white wire to the key-switched or unswitched power spade.
lConnect the black wire to the ground spade.
For the AWT05-509201 Single Amp you will need to use a J-box.
For the AWT05-509202 4 by 5-pin AWT you will only need to use a j-box for systems
with 5 or more weigh bars.
Scale Connector
Pin Description
1 + Excitation
2 - Bridge
3+Bridge
4 - Excitation