Avtech DGC5105T User manual

874Z
d5105t_V1.0
5MP IR Bullet Camera User Manual
Please use this camera with a DVR which supports HD video recording.
Please read the instructions thoroughly before using the product.
C
CA AU UT TI IO ON N
R
RI IS SK K O OF F E EL LE EC CT TR RI IC C S SH HO OC CK K
C
CA AU UT TI IO ON N: :
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of
such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the Restriction
of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or
remove any content in this manual at any time.

FEATURES
1. 1/2.5” CMOS Sensor with up to 5MP video output
2. Low light sensitivity of 0.1 Lux / F1.8, 0Lux (IR LED ON)
3. Quadbrid video output with TVI, CVI, AHD & CVBS
4. DWDR to increase image recognizability in overexposure and dark areas
5. Day and night 24-hour surveillance with IR effective distance up to 50 meters
6. IP66 for weather-proof application
7. Camera parameters adjustable when used with HD CCTV DVR
PACKAGE CONTENT
IR camera User manual Wrench Accessory
DIMENSIONS*
*Dimensional Tolerance: ± 5mm
SPECIFICATIONS*
Video Mode TVI, CVI, AHD & CVBS switchable
Pick-up Element 1/2.5 " CMOS image sensor
Number of Pixels 2560 (H) x 1920 (V)
Video Frame Rate 5MP@ 20fps
Min. Illumination 0.1 Lux / F1.8, 0 Lux (IR LED ON)
S/N Ratio More than 48dB (AGC OFF)
Shutter Speed AUTO : 1/25(30)sec~1/50,000sec
Lens f3.6mm / F1.8
Lens Angle 96° (Horizontal) / 50° (Vertical) / 116° (Diagonal)
IR LED 2 units
IR Effective Distance Up to 50 meters
IR Shift YES
Day & Night Mode YES
Noise Reduction YES
IRIS Mode AES
White Balance AUTO
AGC AUTO
Sharpness Adjustable
Flickerless 50HZ / 60HZ / OFF
BLC Adjustable
DWDR YES
IP Rating IP66
Operating Temperature -20℃~ 40℃
Operating Humidity 90% or less relative humidity
Power Source (±10%) DC12V / 0.5A
Current Consumption (±10%) 100mA (IR lED OFF); 240mA (IR LED ON)
Net Weight (kg) 0.36
* The specifications are subject to change without notice.

INSTALLATION
Step1: Find the wrench supplied in the sales package, and loosen the screw as indicated below to loosen
the joint lock of the bracket.
Note: for lock, and for unlock.
Step2: Locate where to install this camera, and fasten the bracket to the ceiling or wall.
Then, adjust the viewing angle of the camera, and fasten the screw to secure the joint lock of the
bracket.
Note: for lock, and for unlock.
CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a DC 12V regulated power supply.
Note: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The power
tolerance of this unit is DC12V ± 10%. Over maximum DC 12V power input will damage this
unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output to the video input of a DVR with 75Ωcoaxial cable.
Note: To ensure the camera has sufficient protection against moisture, an extra waterproof
measure, such as by using an insulating tape, must be used to cover the power and video
connectors after connection.

CAMERA PARAMETERS
This camera series has its own configuration menu. Please check the user manual of your recorder to
know how to enter the camera menu via your recorder.
Click to show the camera menu and you can move among sub-menus:
/ Move among sub-menus.
/ Change settings.
Call the camera parameters menu or enter the currently-selected item.
MENU REMARK
MAIN-MENU AE BRIGHTNESS 1 ~ 10
EXPOSURE MODE GLOBAL
AWB MODE ATW
MWB Manually adjust the white balance
parameters by modifying R / B gain
parameters.
DAY - NIGHT MODE EXT Use the external light sensor we
added in the camera to detect the
surrounding light condition and
switch to color or B/W mode.
AUTO
COLOR
BW
VIDEO ENHANCE CONTRAST 1 ~ 10
SHARPNESS 1 ~ 10
COLOR GAIN 1 ~ 10
DNR 1 ~ 10
MIRROR DEFAULT
H Horizontal
V Vertical
HV Horizontal & vertical
D-WDR OFF / ON
VIDEO OUTPUT HD TVI / CVI / AHD / CVBS
VIDEO STANDARD Choose the video resolution and
IPS of this camera in different
video output mode.
REBOOT&APPLY
LANGUAGE ENGLISH / SIMPLIFIED
CHINESE / TRADITIONAL
CHINESE / RUSSIAN /
ITALIAN / PORTUGUESE
RESET
SAVE-EXIT Save the changes and exit the
menu.
EXIT Exit the menu without saving