AVYCON AVC-TE21M User manual

HD Analog 2MP/5MP/8MP Cameras
QUICK START GUIDE
VARIFOCAL TURRET DOME CAMERA
HD-TVI / CVI / AHD / CVBS
Introduction
Safety Instructions
Installation
Setup Diagram
2
3
4
5
Package Contents6
Resources7
1
CONTENTS
Thank you for purchasing our product. We make every effort to
update and ensure accuracy of the information contained in this
manual, which may be subject to change from time to time
without prior notice. For any questions or needs, please feel free
to contact us at any time.
INTRODUCTION 2
1)
2)
3)
Please comply with the power supply specications as required
for this equipment and select the correct power supply.
In the case that equipment fails to operate properly, immediately
contact the manufacturer or the nearest service center. Please
do not attempt to disassemble the product or attempt to modify
the product in any manner, which may void warranty.
For cleaning of the lens, be sure to use compressed air or a
dedicated lens cleaner. For cleaning of the plastic shield, use a
soft and dry microber cloth to wipe it. Do not use any detergents
containing alcohol or benzene.
4) Do not drop any object onto the device or knock heavy objects
onto the equipment.
5) Do not put the camera toward any strong light source (including
lighting lamp or sun), which may cause over-exposure or light
leakage (not due to defect of the product) and impair useful life
of the camera.
6) Avoid use of the equipment in any environment other than as
suggested in this manual.
7) Prevent water or any other liquid from owing into the equipment.
8) For replacement of any parts, contact the distributor. Changing
any parts in the device without authorization is not permitted and
may void warranty.
OPERATING ENVIRONMENT
Power Supply DC12V±10%
Temperature -30°C~60°C
Humidity 10%~95%
Altitude -60m~3000m
Atmosphere 86kpa~106kpa
SAFETY INSTRUCTIONS 3
1. Place mounting template sticker in area where you will be
mounting camera to surface that can sustain weight of camera.
2. Remove the ring off the camera by rotating it down to separate
from magnets.
Sticker
Ring
INSTALLATION 4
VARIFOCAL TURRET DOME CAMERA

3. Drill into surface at marked drill holes deep enough to
accommodate for mounting hardware.
• If using the included hardware, insert the three drywall
anchors into holes in the mounting surface and align holes
in camera mounting plate with anchors. Then use included
screws to secure mounting plate and camera to surface.
5. Mounting complete.
6. Focus & Zoom Controls
a. For Manual Lens, nd Focus and Zoom adjustment screws and
use a small athead screwdriver to adjust lens to desired view.
b. For Motorized Lens, please use DVR’s local interface or mobile
device to adjust focus and zoom levels from the camera’s
PTZ/Lens menu to desired view. Should more assistance be
needed with this step, please feel free to visit our website
or contact our Helpdesk number.
Mounting Screw
Drywall Anchors
Set Screws
4. Loosen set screws (pictured below) with included security
wrench.
Adjust the camera to desired angle, then tighten screws and
then place the magnetic ring back onto the camera.
FOCUS
ZOOM
PLEASE CONFIRM THAT VOLTAGE OF POWER SUPPLY USED MATCHES
POWER REQUIRED BY CAMERA, OTHERWISE PERMANENT DAMAGE OR
RISK OF FIRE MAY OCCUR
CAUTION
Power Supply
DVR
Camera
BNC Video Output
Power Connector
CCTV Power Supply
12VDC
Power Outlet
LAN USB DC12V
VGA
SETUP DIAGRAM 5
PACKAGE CONTENTS 6
Zoom
Focus
ZOOM
FOCUS
Varifocal Turret Dome Camera Mounting Template
Drywall Anchor x 3
Mounting Screw x 3 L-Wrench
DC Plug Terminal Block
Need help?
Visit us online for up-to-date software and complete instruction manuals.
1) Visit www.avycon.com
2) Search for the model number of your product.
3) Click on your product and nd appropriate documents on product page.
RESOURCES 7
[email protected]om
www.avycon.com
1 [phone]
1 [phone]
[M-F, 6am-5pm PST]
Technical Support E-mail :
Technical Support Website :
US Helpdesk Number :
Toll Free Number (Canada) :
VARIFOCAL TURRET DOME CAMERA